Engineering topics

Hemmati, H.

Publications and source records attributed to Hemmati, H..

82 records · Page 5

NASA NTRS1991

An electro-optic resonant modulator for coherent optical communication

A resonant cavity electro-optic phase modulator has been designed and implemented to operate at a data rate of 10 Mbps. The modulator consists of an electro-optic crystal located in a highly resonant cavity. The cavity is electro-optically switched on and off resonance, and the phase dispersion near the cavity resonance provides the output phase modulation. The performance of the modulator was measured by first heterodyne detecting the signal to an intermediate frequency, and measuring the spectral characteristics using an RF spectrum analyzer. The measured phase shift is shown to be in good agreement with the theoretical predictions. Further theoretical analysis shows that the design of the modulator can be scaled to operate at 100 Mbps.

Robinson, D. L.↗

NASA NTRS1991

Optical link demonstration with a lightweight transceiver breadboard

A compact optical communications transceiver breadboard was constructed. In order to keep the mass of the breadboard as low as possible the design was made very simple. The entire package weighs less than 5 kg. The optical module uses a 40 mW diode laser and a two-axis voice coil actuator for beam steering. The breadboard is capable of locking onto a laser beacon within its field of view and transmitting the diode laser beam back toward the beacon. Design of the breaboard, details of each component in the breadboard, and current experiments with the package are described.

Hemmati, H.↗

NASA NTRS1989

Environmental testing of a diode-laser-pumped Nd:YAG laser and a set of diode-laser-arrays

Results of the environmental test of a compact, rigid and lightweight diode-laser-pumped Nd:YAG laser module are discussed. All optical elements are bonded onto the module using space applicable epoxy, and two 200 mW diode laser arrays for pump sources are used to achieve 126 mW of CW output with about 7 percent electrical-to-optical conversion efficiency. This laser assembly and a set of 20 semiconductor diode laser arrays were environmentally tested by being subjected to vibrational and thermal conditions similar to those experienced during launch of the Space Shuttle, and both performed well. Nevertheless, some damage to the laser front facet in diode lasers was observed. Significant degradation was observed only on lasers which performed poorly in the life test. Improvements in the reliability of the Nd:YAG laser are suggested.

Hemmati, H.↗

NASA NTRS1988

Performance of efficient Q-switched diode-laser-pumped Nd:YAG and Ho:YLF lasers for space applications

Solid-state lasers pumped by continuous-wave diode lasers can be Q-switched to obtain high peak power output pulses. The dependence of laser-pulse energy, average output power, peak power, and pulse width on pulse-repetition frequency in Q-switched Nd:YAG and Ho:YLF lasers is determined and compared. At low pulse repetition rates, the much longer upper-stage lifetime in Ho:YLF gives a distinct advantage. At higher pulse rates, the overall laser efficiency and the stimulated emission cross section are more important parameters, leading to an advantage for Nd:YAG. The results are of significance for designing lasers for use in space optical communications and remote sensing systems.

Marshall, W. K.↗

NASA NTRS1988

Compact Ho:YLF Laser

Longitudinal pumping by laser diodes increases efficiency. Improved holmium:yttrium lithium fluoride laser radiates as much as 56 mW of power at wavelength of 2.1 micrometer. New Ho:YLF laser more compact and efficient than older, more powerful devices of this type. Compact, efficient Ho:YLF laser based on recent successes in use of diode lasers to pump other types of solid-state lasers.

Hemmati, H.↗

NASA NTRS1987

Efficient holmium:yttrium lithium fluoride laser longitudinally pumped by a semiconductor laser array

Optical pumping of a holmium:yttrium lithium floride (Ho:YLF) crystal with a 790-nm continuous-wave diode-laser array has generated 56 mW of 2.1-micron laser radiation with an optical-to-optical conversion slope efficiency of 33 percent while the crystal temperature is held at 77 K. The lasing threshold occurs at 7 mW of input power, and laser operation continues up to a crystal temperature of 124 K.

Hemmati, H.↗

NASA NTRS1987

Single longitudinal mode operation of semiconductor laser arrays with etalon feedback

The multiple longitudinal mode output of high-power diode-laser arrays is converted into single mode with 97 percent efficiency by optical feedback from a thin (less than 200-micron thick) etalon external to the laser. The coupled cavities formed by addition of the etalon favor a single longitudinal mode. Single-mode operation is retained at 0.1 MHz pulsed rates. Both the near-field and the far-field patterns of the laser array remain nearly unchanged while the array operates in a single longitudinal mode.

Hemmati, H.↗

NASA NTRS1986

Single longitudinal mode operation of semiconductor laser arrays with etalon control

A simple method is devised to obtain a single longitudinal output beam from high-power multilongitudinal mode diode laser arrays. Mode control is achieved by simply placing a thin etalon in front of the laser. The three-cavity laser formed by addition of the etalon favors a single longitudinal mode. This technique is applicable to both continuous wave and pulsed laser modes of operation. Experimental results demonstrating the technique along with future work and possible applications are discussed.

Hemmati, H.↗

NASA NTRS1986

Heat trap with flare as multimode antenna

A heat trap, also called a Winston cone or compound parabolic concentrator, has been designed and built to serve as the beam defining optic for the far-infrared absolute spectrophotometer on the Cosmic Background Explorer satellite. This quasi-optical multimode antenna is coupled to a flared entrance section shaped like a trumpet bell to reduce response to off-axis radiation. The antenna has very low sidelobes over a two-decade frequency range from 1 to 100/cm. Fabrication is described, and stray light data are presented and compared to theory. A novel optical figure test for concentrators is presented.

Mather, J. C.↗

NASA NTRS1985

Submillimeter and millimeter wave characterization of absorbing materials

Several microwave absorbers have been characterized in terms of transmittance and reflectance at frequencies between 35 GHz and 3 THz. The materials studied were a series of iron-loaded cast epoxy absorbers known as Eccosorb. Measurements show that reflectance and absorption coefficient increase with the iron density. A dramatic decrease, by as much as a factor of 2, in absorption coefficient was observed when the samples were cooled from ambient to cryogenic temperatures. A blackbody calibrator to be operated at liquid helium temperature was constructed using the measured optical constants for these absorbers. The measured absorption coefficient for cold Eccosorb CR-110 is within 20 percent of that reported recently by Peterson and Richards.

Hemmati, H.↗