Engineering Papers⌕ Search

Engineering topics

Heidelberg, L. J.

Publications and source records attributed to Heidelberg, L. J..

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Full scale upper surface blown flap noise

A highly noise suppressed TF 34 engine was used to investigate the noise of several powered lift configurations involving upper surface blown (USB) flaps. The configuration variables were nozzle type (i.e. slot and circular with deflector), flap chord length, and flap angle. The results of velocity surveys at both the nozzle exit and the flap trailing edge are also presented and used for correlation of the noise data. Configurations using a long flap design were 4 db quieter than a short flap typical of current trends in USB flap design. The lower noise for the long flap is attributed primarily to the greater velocity decay of the jet at the flap trailing edge. The full-scale data revealed substantially more quadrupole noise in the region near the deflected jet than observed in previous sub-scale tests.

Heidelberg, L. J.↗
NASA NTRS1975

Propulsion system noise reduction

The progress in propulsion system noise reduction is reviewed. The noise technology areas discussed include: fan noise; advances in suppression including conventional acoustic treatment, high Mach number inlets, and wing shielding; engine core noise; flap noise from both under-the-wing and over-the-wing powered-lift systems; supersonic jet noise suppression; and the NASA program in noise prediction.

Feiler, C. E.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an EBF STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An UTW powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An OTW configuration with non-decayer nozzle was about 10 db quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1973

Effect of exhaust nozzle configuration on aerodynamic and acoustic performance of an externally blown flap system with a quiet 6:1 bypass ratio engine

A highly suppressed TF-34 engine was used to investigate engine and flap interaction noise associated with an externally blown flap STOL powered lift system. Noise, efficiency, and velocity decay characteristics of mixed and separate flow exhaust systems including convergent, co-annular, and lobed designs were determined with the engine operating alone. Noise data were then obtained for several of the exhaust configurations with the engine blowing a wing-flap segment. Noise for both the engine alone and the engine with blown flaps showed substantial differences for the various exhaust configurations tested. The differences in observed noise are related primarily to nozzle effective exhaust velocity, flap impingement velocity, and noise spectral shape.

Samanich, N. E.↗
NASA NTRS1973

Highly noise suppressed bypass 6 engine for STOL application

A TF-34 engine with an acoustically treated ground test nacelle was built and tested to determine the feasibility of suppressing fan and core engine noise to the stringent levels required for STOL or short-haul commercial aircraft. The design incorporates wall treatment for the fan and core plus three treated splitter rings in the inlet and two treated splitters in the aft fan duct. Maximum suppression of fan tone noise of 40-45 dB was obtained from both the inlet and aft fan treatment. At rated fan speed, overall noise was reduced by 21 PNdB to a value of 94 PNdB on a 500-foot sideline. The overall noise reduction value was limited by the jet noise floor. Thrust losses due to the acoustic treatment are also discussed.

Jones, W. L.↗
NASA NTRS1973

Effect of exhaust nozzle configuration on aerodynamic and acoustic performance of an externally blown flap system with a quiet 6:1 bypass ratio engine

A highly suppressed TF-34 engine was used to investigate engine and flap interaction noise associated with an externally blown flap STOL powered lift system. Noise, efficiency, and velocity decay characteristics of mixed and separate flow exhaust systems including convergent, co-annular, and lobed designs were determined with the engine operating alone. Noise data were then obtained for several of the exhaust configurations with the engine blowing a wing-flap segment. Noise for both the engine alone and the engine with blown flaps showed substantial differences for the various exhaust configurations tested. The differences in observed noise are related primarily to nozzle effective exhaust velocity, flap impingement velocity, and noise spectral shape.

Samanich, N. E.↗
NASA NTRS1972

Effect of Reynolds number on overall performance of a 3.7-inch-diameter six-stage axial-flow compressor

A 9.4-centimeter (3.7-in.) diameter six-stage axial-flow compressor was tested in argon over a range of inlet pressures corresponding to a Reynolds number range of 30,600 to 160,000. The effect of Reynolds number on efficiency, pressure ratio, work input, maximum flow, and surge is shown. The Reynolds number effects are discussed in terms of changes in boundary-layer thickness, losses, and the resulting changes in throughflow velocity. Significant deviation was noted from the 0.2 power relation often used to express the variation of loss with Reynolds number.

Heidelberg, L. J.↗
NASA NTRS1971

Effect of several porous casing treatments on stall limit and on overall performance of an axial flow compressor rotor

Several geometrically different porous casings were tested with an axial-flow compressor rotor to determine their effects upon the rotor stall-limit line and overall performance. The tests were conducted using both uniform and nonuniform inlet-flow conditions. The rotor performance with the various casing treatments is compared with that obtained with a solid casing. The ability of the various casing treatments to displace the rotor stall-limit line to lower weight flows was observed. Significant stall-margin increases were obtained with several of the porous casings. Peak efficiencies with two of the porous casings were as high as or slightly higher than that obtained with solid casing.

Osborn, W. M.↗