Crystallinity-Independent Toughness in Renewable Poly( l -lactide) Triblock Plastics
Not provided.
Polymer Science↗
Engineering topics
Haugstad, Greg
Publications and source records attributed to Haugstad, Greg.
Crystal-chemical origins of the ultrahigh conductivity of metallic delafossites
Abstract Despite their highly anisotropic complex-oxidic nature, certain delafossite compounds ( e.g ., PdCoO 2 , PtCoO 2 ) are the most conductive oxides known, for reasons that remain poorly understood. Their room-temperature conductivity can exceed that of Au, while their low-temperature electronic mean-free-paths reach an astonishing 20 μm. It is widely accepted that these materials must be ultrapure to achieve this, although the methods for their growth (which produce only small crystals) are not typically capable of such. Here, we report a different approach to PdCoO 2 crystal growth, using chemical vapor transport methods to achieve order-of-magnitude gains in size, the highest structural qualities yet reported, and record residual resistivity ratios ( > 440). Nevertheless, detailed mass spectrometry measurements on these materials reveal that they are not ultrapure in a general sense, typically harboring 100s-of-parts-per-million impurity levels. Through quantitative crystal-chemical analyses, we resolve this apparent dichotomy, showing that the vast majority of impurities are forced to reside in the Co-O octahedral layers, leaving the conductive Pd sheets highly pure (∼1 ppm impurity concentrations). These purities are shown to be in quantitative agreement with measured residual resistivities. We thus conclude that a sublattice purification mechanism is essential to the ultrahigh low-temperature conductivity and mean-free-path of metallic delafossites.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Polyethylene Blends for Improved Oxygen Barrier: Processing-Dependent Microstructure and Gas Permeability
Here this work demonstrates a greater than expected enhancement of oxygen barrier properties in linear low-density polyethylene (LLDPE)-based materials by blending LLDPE with high-density polyethylene (HDPE). The films made by melt pressing the LLDPE/HDPE blends had a greater reduction in oxygen permeability coefficients (PO 2 ) than predicted using common permeability reduction models, i.e., the harmonic average model and zero-permeability nanofiller model. The reduction of PO 2 was attributed to the presence of spherulite crystal structures, as revealed by atomic force microscopy combined with infrared spectroscopy (AFM-IR). The LLDPE matrix exhibited significant spherulite formation even at a relatively low addition of HDPEs, which likely formed tortuous pathways for diffusing oxygen molecules. Transport results from melt-pressed films contrast with the results from films with similar compositions prepared by film blowing, which did not show barrier enhancement beyond expectation. AFM-IR revealed that the blown films lacked spherulite crystals likely due to stretching in the machine direction followed by rapid cooling. These findings demonstrate the role of processing in controlling microstructures and thus the oxygen barrier performance. This work offers the possibility of achieving easily recyclable LLDPE-based packaging materials by simple blending of polyethylenes with different crystalline content.
36 MATERIALS SCIENCE↗
Efficient Metal–Halide Perovskite Photovoltaic Cells Deposited via Vapor Transport Deposition
Photovoltaic cells based on metal-halide perovskites have exceeded the performance of other thin film technologies and rival the performance of devices based on archetypical silicon. Attractively, the perovskite active layer can be processed via a variety of solution- and vapor-based methods. Herein, emphasis is on the use of vapor transport codeposition (VTD) to process efficient n–i–p photovoltaic cells based on methylammonium lead iodide (MAPbI 3 ). VTD utilizes a hot-walled reactor operated under moderate vacuum in the range of 0.5–10 Torr. The organic and metal-halide precursors are heated with the resulting vapor transported by a N 2 carrier gas to a cooled substrate where they condense and react to form a perovskite film. The efficiency of photovoltaic devices based on VTD-processed MAPbI 3 is found to be highest in films with excess lead iodide content, with champion devices realizing exceeding 12%.
14 SOLAR ENERGY↗
Blending Polyurethane Thermosets Using Dynamic Urethane Exchange
Recycling crosslinked polyurethanes (PUs) is accomplished through mechanical or chemical processes that are energy-intensive or produce plastics of lesser value. Polymer recycling processes are notably intolerant of polymer mixtures, yet the ability to reprocess and compatibilize two or more crosslinked PUs together will make this process more amenable to mixed waste streams while offering an opportunity to tune the properties of the recycled polymer products. Here, we blend a rigid polyester PU and a soft polyether PU using twin-screw extrusion to yield materials with tunable mechanical properties based on the feed composition. Their material properties were compared to those of compression-molded reprocessed blends and blends where the monomers were mixed prior to synthesis. The extruded materials showed similar mechanical and thermal properties to newly prepared blends and had higher-value mechanical properties compared to the samples reprocessed via compression molding. The morphologies of the blends were observed using phase imaging via atomic force microscopy to show that there is less phase separation in the extruded materials compared to compression-molded blends. The mechanical properties of these materials were tunable from soft to elastomeric to rigid based on the feed composition, and this tunability was demonstrated through four consecutive reprocessing cycles, through which the mechanical properties were steadily varied from rigid to soft by incorporating increasing amounts of soft polyether PU material. Here, this blending method for reprocessing mixed waste compatibilizes different PUs and provides a means to tune the mechanical properties of a PU product, even if starting from waste streams of varying compositions. As such, this process represents an intriguing new approach for polymer reprocessing.
Extrusion↗