Engineering topics
Publications and source records attributed to Hassan, H. A..
A one-equation turbulence model based on the turbulent kinetic energy equation is presented. The model is motivated by the success of the Johnson-King model and incorporates a number of features uncovered by Simpson's experiments on separated flows. Based on the results obtained, the model duplicates the success of algebraic models in attached flow regions and outperforms the two-equation models in detached flow regions.
A grid generation and adaptation procedure based on the method of transfinite interpolation is incorporated into the Direct Simulation Monte Carlo Method of Bird. In addition, time is advanced based on a local criterion. The resulting procedure is used to calculate steady flows past wedges and cones. Five chemical species are considered. In general, the modifications result in a reduced computational effort. Moreover, preliminary results suggest that the simulation method is time step dependent if requirements on cell sizes are not met.
Grid-embedding techniques are presently applied to the solutions of the Euler equations on Cartesian grids for the NACA 0012 airfoil and the multielement SKF1.1 airfoil at transonic speeds. Based on comparisons with solutions on fine grids, it is shown that the present scheme, when used in conjunction with the Runge-Kutta time-stepping scheme as well as Cartesian grids, yields reduced memory requirements and a substantial reduction in computational time, without loss of accuracy.
A viscous-inviscid interaction procedure for transonic airfoils using an Euler/integral boundary layer formulation and Cartesian grids is presented. The approach is based on a time dependent formulation for both the integral boundary layer equations and the Euler equations. Effects of upstream history on the shear stress are modeled by a time dependent rate equation derived from the turbulent kinetic energy equation. Results are presented for two of the test cases reported by Cook et al. (1979) for the RAE 2822 supercritical airfoil and one of the cases reported by Harris (1981) for the NACA 0012 symmetric airfoil. In general, the results are in good agreement with experiment.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
A method is presented for the calculation of transonic flows past wings using Cartesian grids. The calculations are based on a finite volume formulation of the Euler equations. Results are presented for a rectangular wing with a flat tip and the ONERA M6 wing. In general, the results are in good agreement with other computations and available experiment. However, Cartesian grids require a greater number of points than body fitted grids in order to resolve the flow properties near the leading edge of a swept wing.
Using ideas from kinetic theory, the Navier-Stokes equations are modified in such a way that they can be cast as a set of first order hyperbolic equations. This is achieved by incorporating time dependent terms into the definition of the stress tensor and the heat flux vectors. The boundary conditions are then determined from the theory of characteristics. Because the resulting equations reduce to the traditional Navier-Stokes equations when the steady state is reached, the present approach provides a straightforward scheme for the determination of inflow and outflow boundary conditions. The method is validated by comparing its predictions with exact and numerical solutions of the steady Navier-Stokes equations.
Using ideas from the kinetic theory, the Navier-Stokes equations are modified in such a way that they can be cast as a set of first order hyperbolic equations. This is achieved by incorporating time dependent terms into the definition of the stress tensor and the heat flux vectors. The boundary conditions are then determined from the theory of characteristics. Because the resulting equations reduce to the traditional Navier-Stokes equations when the steady state is reached, the present approach provides a straightforward scheme for the determination of inflow and outflow boundary conditions. The method is validated by comparing its predictions with known exact solutions of the steady Navier-Stokes equations.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
A new approach has been developed to study the initial roll-up of aircraft wakes. This approach is based on the solution of the three-dimensional Euler equations subject to inflow and initial conditions predicted by a vortex-lattice method. This procedure allows for the solution of this complex problem without any empirical inputs. However, valid solutions are limited to those flowfields generated by wings which are free of flow separation. Results are presented for four configurations: a rectangular wing with part span flap, a rectangular wing, a typical transport-type configuration and a fighter configuration. In addition, an assessment of an 'unsteady 2-D analogy' was undertaken using the 2-D time accurate Euler equation solutions in crossflow planes. In general, predictions from the 2-D unsteady analogy coincided with the 3-D results which were found to be in good agreement with available experimental data.
A semi-implicit finite volume formulation is used to study flows with chemical reactions. In this formulation the source terms resulting from the chemical reactions are treated implicitly and the resulting system of partial differential equations is solved using two time-stepping schemes. The first is based on the Runge-Kutta method while the second is based on an Adams predictor-corrector method. Results show that improvements in computational efficiency depend to a large extent on the manner in which the source term is treated. Further, analysis and computation indicate that the Runge-Kutta method is more efficient than the Adams methods. Finally, an adaptive time stepping scheme is developed to study problems involving shock ignition. Calculations for a hydrogen-air system agree well with other methods.
Explore the source record for details and available documents.
An explicit finite difference solver for the Euler equations was developed and used to calculate the flow past two of the AGARD standard aeroelastic configurations, an NACA 64A010 and an NLR 7301. The algorithm employed uses a modified four step Runge-Kutta time stepping scheme, boundary conditions determined from the time-dependent theory of characteristics and an unsteady automatic grid generation procedure. In general, the calculated results are in good agreement with available experiment. Moreover, they demonstrate the importance of using the Euler equations for super-critical airfoils and in situations where the transonic small disturbance theory results in poor agreement with experiment.
Explore the source record for details and available documents.
Explore the source record for details and available documents.