Engineering topics

Haskin, Larry A.

Publications and source records attributed to Haskin, Larry A..

At least 55 records · Page 3

NASA NTRS1992

Electrolytic smelting of lunar rock for oxygen, iron, and silicon

Preliminary studies of the electrochemical properties of silicate melts such as those available from heating of lunar mare soils indicate that conductivities are high enough for design of a practical electrolytic cell. The nature and kinetics of the electrode reactions, which involve reduction of Fe(++) and Si(IV) and oxidation of silicate anions as the primary, product-forming reactions, are also satisfactory. A survey of the efficiencies for production (amount of product for a given current) of O2, Fe(sup 0), and Si(sup 0) as functions of potential and of electrolyte composition indicate that conditions can be chosen to yield high production efficiencies. We also conclude that electronic conductivity does not occur to a significant extent. Based on these data, a cell with electrodes of 30 sq m in area operating between 1 and 5V with a current between 1.6 and 3.5(10)(exp 5) A for a mean power requirement of 0.54 MW and total energy use of approximately 13 MWhr per 24-hr day would produce 1 ton of O2, 0.81 ton of Fe(sup 0), 0.65 ton of Si(sup 0) (as Fe(sup 0)-Si(sup 0) alloy), and about 3.5 tons of silicate melt of altered composition per 24 hr. Adjustable distance between electrodes could offer flexibility with respect to feedstock and power source.

Haskin, Larry A.↗

NASA NTRS1992

Genesis of compositional characteristics of Stillwater AN-I and AN-II thick anorthosite units

Compositional variations among samples of the thick Stillwater anorthosite units are used here to model the mechanism by which the anorthosite formed. Suspended plagioclase, on reaching a volumetric crystal concentration of about 65 percent, formed a plagioclase framework here called cumulus plagioclase (CP). Within the interstices among the crystals, some plagioclase and pyroxene precipitated, producing what is here called adcumulus plagioclase and pyroxene (APP). The final materials consists mainly of plagioclase and pyroxene formed from complete crystallization of trapped supporting liquid and called intercumulus plagioclase and pyroxene (IPP). Where the CP framework was relatively open initially, bulk liquid communicated with the interior of the framework to produce APP. Where this communication with the bulk liquid stopped or was prevented initially, the intercumulus liquid froze. Where the CP framework was more tightly packed initially, a relatively higher proportion of IPP to APP was produced.

Haskin, Larry A.↗

NASA NTRS1992

Oxygen from the lunar soil by molten silicate electrolysis

Accepting that oxygen, rather than gigantic gems or gold, is likely to make the Moon's Klondike, the extraction of oxygen from the lunar soil by molten silicate electrolysis has chosen to be investigated. Process theory and proposed lunar factory are addressed.

Colson, Russell O.↗

NASA NTRS1992

Manufacturing and fabrication, part 3

The accessibility of material and energy off the Earth and the leverage that these nonterrestrial resources can exert on the space transportation system are important influences on the long-term goal of exploring the solar system. Research on separation of lunar materials and manufacturing of useful products from them is in its infancy. A few possible processes and products are described in this report. Specific attention is given to oxygen, metal, and silicate products.

Sastri, Sankar↗

NASA NTRS1992

Glass and ceramics

A variety of glasses and ceramics can be produced from bulk lunar materials or from separated components. Glassy products include sintered regolith, quenched molten basalt, and transparent glass formed from fused plagioclase. No research has been carried out on lunar material or close simulants, so properties are not known in detail; however, common glass technologies such as molding and spinning seem feasible. Possible methods for producing glass and ceramic materials are discussed along with some potential uses of the resulting products.

Haskin, Larry A.↗

NASA NTRS1992

Cement and concrete

To produce lunar cement, high-temperature processing will be required. It may be possible to make calcium-rich silicate and aluminate for cement by solar heating of lunar pyroxene and feldspar, or chemical treatment may be required to enrich the calcium and aluminum in lunar soil. The effects of magnesium and ferrous iron present in the starting materials and products would need to be evaluated. So would the problems of grinding to produce cement, mixing, forming in vacuo and low gravity, and minimizing water loss.

Corley, Gene↗

NASA NTRS1992

Steady state composition with low Fe(2+) concentrations for efficient O2 production by 'magma' electrolysis of lunar soils

Parameters are estimated for a hypothetical, well stirred, continuous-feed electrolytic cell that converts 20 percent of a lunar soil feedstock to O2 gas, 26 percent to Fe-Si metal, 13 percent to spinel, and 41 percent to slag. Advantages of a molten Fe-Si cathode for trapping metal on reduction, a relatively conductive steady-state composition in equilibrium with spinel (a proposed container material), and close electrodes (less than 1 cm cathode-anode distance) are discussed. To produce 1 ton of O2, about 6 MHW of energy are required for the electrolysis and IR heating within the melt, and another about 6 MHW may be introduced as waste heat through internal resistance of the electrodes. Thus, to produce 1 ton of O2 per 24 hours, about 0.5 MW of power delivered to the cell would be required.

Haskin, Larry A.↗

NASA NTRS1991

A ferroan region of the lunar highlands as recorded in meteorites MAC88104 and MAC88105

MAC88104 and 88105, paired meteorites of noritic anorthosite composition, are examined. Results indicate that these meteorites contain a variety of materials including impact-melt breccias, igneous and metamorphosed bressia clasts, glass clasts and veins, mineral clasts, and extralunar meteoritic debris. Compositions of the bulk meteorite and its components suggest that it came from a region of the moon's crust that was highly aluminous, low in incompatible trace elements, and ferroan in character.

Jolliff, Bradley L.↗

NASA NTRS1991

Compositional variations among whole-rock fragments of the L6 chondrite Bruderheim

Twenty about 100-mg random fragments of the Bruderheim chondrite were analyzed by INAA to determine extents of heterogeneity and to check earlier results that gave anomalous LREE concentrations. Considerable compositional heterogeneity was observed in both concentrations (maximum/minimum of 1.7 for Ir, 1.8 for Na, 6.8 for La, 7.4 for Co) and concentration ratios (greater than 3 x for Ni/Co and La/Eu). Compositions could be modeled quantitatively in terms of end-member components of constant composition representing the minerals olivine + orthopyroxene, clinopyroxene, plagioclase, kamacite, taenite, troilite, chromite, and phosphate. The model yields the proportions of minerals in each sample as well as the meteorite as a whole; accurate determination of the end members depends on high intrasample precision for many elements. No evidence of compositional heterogeneity of end members for trace elements was found. It is shown that these analyses, which used only about 2 grams of the meteorite, are equivalent in accuracy to a single sample of several tens of grams, and that knowledge of the extent of heterogeneity is essential to knowing the quality of sampling as well as for comparing results from one analysis with another and of one meteorite with another.

Haas, Johnson R.↗

NASA NTRS1991

Electrolysis of lunar soil to produce oxygen and metals

The discussion of melt electrolysis consists of three sections. The implications of the chemistry and physics of fluxed and raw melts on melt electrolysis are discussed first. This includes discussion of the factor that influence melt resistivity, melt viscosity, oxygen production efficiency, and the theoretical energy required to produce oxygen. Second, the implications of phase equilibria and solubilities in silicate melts on the selection of materials for container and electrodes are discussed. The implications of proposed container and electrode materials on melt composition and how this effects expected resistivities, viscosities, as outlined in the first section are discussed. Finally, a general discussion of the basic features of both the fluxed and unfluxed melt electrolysis is given, including their advantages and disadvantages and how they compare with alternative processes.

Colson, Russell O.↗

NASA NTRS1991

Magma Electrolysis: An update

Electrolytic extraction of O2 from molten lunar soil is conceptually simple and thus a candidate process for producing O2 on the Moon. Possible container and electrode materials are being tested for durability in corrosive high-temperature silicate melts and looking for complications that might increase energy requirements. Gaseous oxygen is being produced by electrolysis of 1-2 gram quantities of silicate melts in spinel (MgAl2O4) crucibles; in these melts, spinel is a stable phase. The concentration of FeO was kept low because FeO decrease O2 production efficiency. Platinum electrodes were placed about 0.5 cm apart in the melt. The spinel crucible was still intact after 40 minutes of electrolysis, when the experiment was halted for examination. The Pt anode was also intact; its Pt was maintained in a dynamci state in which the anode was continuously oxidized but quickly reduced again by the silicate melt, inhibiting migration of Pt away from the anode. In melts with low concentrations of Al2O3 + SiO2 (2 wt percent), the energy of resistance heating was only approximately equal to 10 to 20 percent of the theoretical amount required to produce O2. In melts substantially more concentrated in Al2O3 + SiO2, higher melt viscosity resulted in frothing that, in the worst case, caused high enough melt resistivities to raise the energy requirements to nearly 10 times theoretical. Both Fe and Si are produced at the cathode; in iron-rich melts, a- and c-iron and molten ferrosilicon were observed. Production was also observed at the cathode of a previously unrecognized gas; which is not yet identified. The solubility of metallic species was measured in silicate melts. They are too low to reduce significantly the efficiency of O2 production.

Colson, Russell O.↗

NASA NTRS1991

A geochemical assessment of possible lunar ore formation

The Moon apparently formed without appreciable water or other relatively volatile materials. Interior concentrations of water or other volatile substances appear to be extremely low. On Earth, water is important to the genesis of nearly all types of ores. Thus, some have reasoned that only abundant elements would occur in ore concentrations. The definition and recognition of ores on the Moon challenge the imaginations and the terrestrial perceptions of ore bodies. Lunar ores included solar-wind soaked soils, which contain abundant but dilute H, C, N, and noble gases (including He-3). Oxygen must be mined; soils contain approximately 45 percent (wt). Mainstream processes of rock formation concentrated Si, Mg, Al, Fe, and Ca, and possibly Ti and Cr. The highland surface contains approximately 70 percent (wt) feldspar (mainly CaAl2Si2O8), which can be separated from some highland soils. Small fragments of dunite were collected; dunite may occur in walls and central peaks of some craters. Theoretical extensions of observations of lunar samples suggest that the Moon may have produced ores of trace elements. Some small fragments have trace-element concentrations 10(exp 4) times higher than the lunar average, indicating that effective geochemical separations occurred; processes included fractional crystallization, silicate immiscibility, vaporization and condensation, and sulfide metamorphism. Operations of these processes acting on indigenous materials and on meteoritic material in the regolith could have produced ores. Infalling carbonaceous meteorites and comets have added water and hydrocarbons that may have been cold-trapped. Vesicles in basalts, pyroclastic beads, and reported transient events suggest gag emission from the lunar interior; such gas might concentrate and transport rare elements. Large impacts may disperse ores or produce them through deposition of heat at depth and by vaporization and subsequent condensation. The main problem in assessing lunar resources is the ignorance about the largely unexplored Moon.

Haskin, Larry A.↗

NASA NTRS1991

On prediction and discovery of lunar ores

Sampling of lunar material and remote geochemical, mineralogical, and photogeologic sensing of the lunar surface, while meager, provide first-cut information about lunar composition and geochemical separation processes. Knowledge of elemental abundances in known lunar materials indicates which common lunar materials might serve as ores if there is economic demand and if economical extraction processes can be developed, remote sensing can be used to extend the understanding of the Moon's major geochemical separations and to locate potential ore bodies. Observed geochemical processes might lead to ores of less abundant elements under extreme local conditions.

Haskin, Larry A.↗

NASA NTRS1990

Electrochemistry of cations in diopsidic melt - Determining diffusion rates and redox potentials from voltammetric curves

Results are presented on determinations of reduction potentials and their temperature dependence of selected ions in diopsidic melt, by using linear sweep voltammetry. Diffusion coefficients were measured for cations of Eu, Mn, Cr, and In. Enthalpies and entropies of reduction were determined for the cations V(V), Cr(3+), Mn(2+), Mn(3+), Fe(2+), Cu(2+), Mo(VI), Sn(IV), and Eu(3+). Reduction potentials were used to study the structural state of cations in the melt.

Colson, Russell O.↗

NASA NTRS1990

Oxygen production by electrolysis of molten lunar regolith

The goal of this study was threefold. First, the theoretical energy requirements of the process were to be defined. This includes studies of the relevant oxidation-reduction reactions in the melt, their kinetics and energies of reaction, and experimental determination of production efficiencies and melt resistivities as functions of melt composition and applied potential. Second, the product(s) of silicate electrolysis were to be characterized. This includes: (1) evaluating the phase relationships in the systems SiO2-TiO2-Al2O3-MgO-FeO-CaO and Fe-Si; (2) estimating the compositions of the metal products as a function of applied potential and feedstock composition based on phase equilibria in the Fe-Si system and free energy values for SiO2 and FeO reported in the literature; (3) definition of compositions of products in actual experiments; and (4) definition of the form the product takes (whether phases separate or remain fixed, whether crystals settle or float in the remaining melt, and how large crystals form). Third, materials for these highly corrosive high-temperature silicate melts were to be identified. This includes identifing materials that may be either inert or thermodynamically stable in these melts, and experimental testing of the materials to confirm that they do not deteriorate. The results are discussed within this framework.

Haskin, Larry A.↗

NASA NTRS1990

Lunar oxygen and metal for use in near-Earth space: Magma electrolysis

Because it is energetically easier to get material from the Moon to Earth orbit than from the Earth itself, the Moon is a potentially valuable source of materials for use in space. The unique conditions on the Moon, such as vacuum, absence of many reagents common on the Earth, and the presence of very nontraditional ores suggest that a unique and nontraditional process for extracting materials from the ores may prove the most practical. With this in mind, an investigation of unfluxed silicate electrolysis as a method for extracting oxygen, iron, and silicon from lunar regolith was initiated and is discussed. The advantages of the process include simplicity of concept, absence of need to supply reagents from Earth, and low power and mass requirements for the processing plant. Disadvantages include the need for uninterrupted high temperature and the highly corrosive nature of the high-temperature silicate melts which has made identifying suitable electrode and container materials difficult.

Colson, Russell O.↗

NASA NTRS1990

Lunar resources: Toward living off the lunar land

The following topics are addressed: (1) lunar resources and surface conditions; (2) guidelines for early lunar technologies; (3) the lunar farm; (4) the lunar filling station; (5) lunar construction materials; (6) the lunar power company; (7) the electrolysis of molten silicate as a means of producing oxygen and metals for use on the Moon and in near-Earth space.

Haskin, Larry A.↗

NASA NTRS1990

Lunar oxygen and metal for use in near-earth space - Magma electrolysis

The unique conditions on the moon, such as vacuum, absence of many reagents common on the earth, and presence of very nontraditional 'ores', suggest that a unique and nontraditional process for extracting materials from the ores may prove the most practical. An investigation has begun into unfluxed silicate electrolysis as a method for extracting oxygen, Fe, and Si from lunar regolith. The advantages of the process include simplicity of concept, absence of need to supply reagents from the earth, and low power and mass requirements for the processing plant. Disadvantages include the need for uninterrupted high temperature and the highly corrosive nature of the high-temperature silicate melts, which has made identifying suitable electrode and container materials difficult.

Colson, Russell O.↗