Engineering topics

Haskey, S. R.

Publications and source records attributed to Haskey, S. R..

12 records

DOE OSTI2024

A near X-point charge exchange neutral spectroscopy (CENS) system for DIII-D

A 16 channel spectroscopy system has been installed on DIII-D to provide information about the energy distribution of the atomic neutrals using the Doppler shift and broadening of passive Balmer-α emission. Here, the lines of sight are dominantly in the toroidal direction, with tangencies near the lowest point on closed magnetic flux surfaces moving from the lower divertor upward into the confined plasma. This allows the system to provide details of the neutrals as they undergo various atomic physics processes while traveling upward from the lower divertor. The spectrally resolved measurements provide several advantages that complement typical optical filter based measurements of hydrogenic spectral lines. These include more direct measurements of the neutrals that fuel deeper in the plasma and capturing neutral velocity distribution information via the Doppler broadened and shifted line. In addition, the spectral separation of higher energy “thermal” neutrals and bright cold emission from the scrape-off layer allows for a more straightforward calculation of the underlying neutral densities based on the emission because of the dependence of the thermal emission on confined plasma properties that are approximately flux functions and well measured.

Atomic and molecular physics↗

DOE OSTI2023

Role of edge-localized neoclassical tearing modes in quiescent H-mode plasmas in the DIII-D tokamak

The edge-harmonic oscillations (EHOs) in standard quiescent H-mode (QH-mode) plasmas in DIII-D are consistent with edge-localized neoclassical tearing modes (NTMs) based on nonlinear two-fluid MHD simulations. Using kinetic equilibria constrained by edge profile measurements, the MHD simulations show that the n = 1 NTM and its harmonics can be destabilized at the pedestal top of QH-mode plasma by the edge bootstrap current. The simulations further show that the unstable NTMs can saturate either at small (<2% ψ N ) or large (>4% ψ N ) island width depending on the magnitude of the edge bootstrap current, where ψ N is the normalized radius in poloidal flux. The onset of the EHO also results in a prompt decrease in the pedestal width and height, consistent with simulation results for the onset of the NTM at the top of the QH-mode pedestal. This suggests that the avoidance of edge-localized modes (ELMs) in QH-mode can be attributed to the enhanced local transport induced by the NTM that is sufficient to prevent the expansion of the pedestal to an unstable width, analogous to the mechanism explored for ELM suppression by resonant magnetic perturbations. Nonlinear MHD simulations scanning the E × B frequency and the ratio of parallel and perpendicular thermal diffusivity (χ | /χ ⊥ ) at the pedestal top show that edge-localized NTMs are destabilized for conditions of high E × B frequency, high pedestal temperature, and low pedestal density, qualitatively consistent with experimental conditions required for observing the EHO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Details of the neutral energy distribution and ionization source using spectrally resolved Balmer-alpha measurements on DIII-D

Spectrally resolved passive Balmer- α (D- α, H- α) measurements from the DIII-D 16 channel edge main-ion charge exchange recombination system confirm the presence of higher energy neutrals (“thermal” neutrals) in addition to the cold neutrals that recycle off the walls in the edge region of DIII-D plasmas. Charge exchange between thermal ions and edge neutrals transfers energy and momentum between the populations giving rise to thermal neutrals with energies approximating the ions in the pedestal region. Multiple charge exchange events in succession allow an electron to effectively take a random walk, transferring from ion to ion, providing a pathway of increasing energy and velocity, permitting a neutral to get deeper into the plasma before a final ionization event that contributes to the ion and electron particle fueling. Spectrally resolved measurements provide information about the density and velocity distribution of these neutrals, which has been historically valuable for validating Monte Carlo neutral models, which include the multi stage charge exchange dynamics. Here, in this study, a multi-channel set of such measurements is used to specifically isolate the details of the thermal neutrals that are responsible for fueling inside the pedestal top. Being able to separate the thermal from the cold emission overcomes several challenges associated with optical filter-based neutral density measurements. The neutral dynamics, deeper fueling by the thermal neutrals, and spectral measurement are modeled with the FIDASIM Monte Carlo collisional radiative code, which also produces synthetic spectra with a shape that is in close agreement with the measurements. By scaling the number of neutrals in the simulation to match the intensity of the thermal emission, we show it is possible to obtain local neutral densities and ionization source rates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Local measurements of the pedestal magnetic field profile throughout the ELM cycle on DIII-D

We report new high speed localized measurements of the pedestal magnetic field during the edge localized mode (ELM) cycle of a DIII-D High confinement mode (H-mode) discharge indicate a temporally and spatial complex redistribution of the edge current density profile, $j_{edge}$. The measurement technique extracts the magnetic field magnitude, $\textit{B}$, via the spectral separation of Stark-split neutral beam radiation in the pedestal. Single spatial channel measurements from a novel spatial heterodyne spectrometer are validated in discharges with core current profile changes. The technique measures Stark-splitting changes that imply $\textit{B}$ changes as small as 1 mT with high time resolution (50 μs). At normalized poloidal flux $ψ_n$ = 1.0, $\textit{B}$ appears saturated in the inter-ELM period and then rapidly decreases in <200 μs by ~1%, before edge recycling emission begins to increase. Radially inboard of $j_{edge}$, $\textit{B}$ increases at the ELM crash. The behavior is consistent with a rapid collapse of $j_{edge}$ at the ELM crash and subsequent pedestal recovery. In some discharges, at $ψ_n$ < 0.96, changes in $\textit{B}$ are observed throughout the ELM cycle. In others, $\textit{B}$ recovers and is relatively stable until a few ms leading up to the next crash. Measurements of $\textit{B}$ during the H-mode transition show a large increase at $ψ_n$ = 1 with little change at $ψ_n$ = 0.9, consistent with the formation of the edge bootstrap current density peak. The $ψ_n$ = 0.9 spectrum is complicated by predicted changes to the Stark component intensities with density at the L–H transition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Studies of EC pre-ionization in DIII-D to support development of ITER plasma initiation

New experiments have been conducted at DIII-D to improve the physics understanding of plasma initiation assisted by electron cyclotron (EC) wave injection, allowing better extrapolation to ITER. This has been achieved by applying an EC pulse prior to start of the inductive plasma initiation (i.e. the generation of a loop voltage). A pre-plasma was formed during the EC pulse that was characterized in terms of the maximum density and temperature. Parametric scans were performed to study the influence of the EC injected power, EC injection angle, and pre-fill gas pressure on the pre-plasma creation process. These experiments showed that pre-ionized plasma of good quality can have a significant effect on the subsequent V loop induced plasma initiation process, i.e. a high density pre-plasma, increases the plasma current rise and speed at which ionization is achieved when the V loop is applied. Here, a good quality pre-plasma is one that achieved a significant degree of ionization, mainly obtained by providing sufficient ECH power in DIII-D of the order of 1 MW. It was found that a minimum EC power of 0.5 MW was required in DIII-D to create ionization, and this would scale to a minimum power of roughly 6.5 MW for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Ion thermal transport in the H-mode edge transport barrier on DIII-D

The power balance ion heat flux in the pedestal region on DIII-D increases and becomes increasingly anomalous (above conventional neoclassical) in experiments with higher temperature and lower density pedestals where the ion collisionality ($v^*_i$) is lowered toward values expected on ITER. Direct measurements of the main-ion temperature are shown to be essential on DIII-D when calculating the ion heat flux due to differences between the temperature of $D^+$ and the more commonly measured $C^{6+}$ impurity ions approaching the separatrix. Neoclassical transport calculations from NEO and non-linear gyrokinetic calculations using CGYRO are consistent with these observations and show that while neoclassical transport plays an important role, the turbulent ion heat flux due to ion scale electrostatic turbulence is significant and can contribute similar or larger ion heat fluxes at lower collisionality. Beam emission spectroscopy and Doppler backscattering measurements in the steep gradient region of the H-mode pedestal reveal increased broadband, long-wavelength ion scale fluctuations for the low $v^*_i$ discharges at the radius where the non-linear CGYRO simulations were run. Taken together, increased fluctuations, power balance calculations, and gyrokinetic simulations show that the above neoclassical ion heat fluxes, including the increases at lower $v^*_i$, are likely due to weakly suppressed ion scale electrostatic turbulence. These new results are based on world first inferred ion and electron heat fluxes in the pedestal region of deuterium plasmas using direct measurements of the deuterium temperature for power balance across ion collisionalities covering an order of magnitude from high $v^*_i$ values of 1.3 down to ITER relevant $v^*_i$ ~0.1.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

New understanding of inter-ELM pedestal turbulence, transport, and gradient behavior in the DIII-D tokamak

New observations of pedestal localized turbulence in the inter-ELM period of H-mode plasmas in DIII-D show that ion temperature gradient mode scale (ITG-scale) density fluctuation (ñ) increases immediately after each ELM crash and is quickly suppressed during the increase in local E × B shear. This excitation and subsequent suppression of ITG-scale ñ can explain the previously reported anomalous ion heat flux, Qi during the ELM (Viezzer et al 2017 Nucl. Fusion 57 022020). Shorter wavelength trapped electron mode scale (TEM-scale) ñ starts to increase at a critical pedestal temperature gradient (∇Te,ped) and saturates as local E × B shear, ${T}_{\mathrm{i}}^{\mathrm{C}\mathrm{6}+}/{T}_{\mathrm{e}}$ ratio, and ∇Te,ped saturate. This TEM-scale ñ, which has the potential to cause electron (and also ion) heat transport, is consistent with driving an anomalous electron heat flux Qe, where Qe is estimated between ELMs using experimental profiles and power balance. Both ITG- and TEM-scale ñ amplitude variations with background Ti/Te and ∇ne,ped are found to be consistent with theoretical predictions of these measured density fluctuations being ITG and TEM instabilities respectively. Furthermore, these new and unique observations on the nature of turbulence and their potential contributions to electron and ion heat fluxes at different ELM periods (i.e. collapse, recovery, and saturation phases of pedestal gradients) can significantly test and improve our pedestal predictive capabilities for ITER and other future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Testing the DIII-D co/counter off-axis neutral beam injected power and ability to balance injected torque

DIII-D has undergone a major upgrade and successfully injected high power off-axis neutral beams (~4 MW) in both co-current and counter-current directions. This capability of high power co/counter steerable off-axis neutral beams on a major tokamak opens a unique parameter space of broad pressure and current profiles for high beta steady-state advanced tokamak (AT) scenarios, while retaining the ability to balance the injected torque for low rotation studies. This co/counter off-axis neutral beam capability is being used to validate physics-based energetic particle and thermal transport models for designing next-step facilities based on the steady-state AT approach. This paper reports on the critical evaluation of the transmitted power and energetic ion population produced by this heating and current drive system, which is assessed through visible imaging, neutron measurements and rotation profile measurements at balanced torque. Minimal losses of neutral beam power have been achieved by optimizing the strongly focused ion sources required to pass through the aperture. Tilting of the ion source has been guided by fast visible imaging and resulted in neutral beam injection along the design centerline with empirical characterization of each beam's divergence derived from the imaging data and used in the NUBEAM description of the beam injection. Through exclusive power injection of each neutral beam into MHD quiescent plasmas across a range of neutral beam voltage, perveance and plasma current we conclude that a modest reduction (~10%–15%) of transmitted power compared to on-axis, standard focus has been incurred. We report corrections that more accurately represent the injected power. Good ability to balance the neutral beam torque has been demonstrated by injecting the new off-axis counter injecting beam against the existing off-axis co-injected beam in 2.0 T, 1.0 MA, MHD quiescent L-mode plasmas. Furthermore, the torque balance studies verify the ability to operate with balanced injection, which is critical for achieving low torque and low rotation operation for physics studies and in ITER demonstration discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Radially resolved active charge exchange measurements of the hydrogenic isotope fraction on DIII-D

Radially resolved hydrogenic isotope fraction measurement capabilities have been developed for DIII-D using the main-ion charge exchange recombination (MICER) spectroscopy system in preparation for mixed hydrogen and deuterium experiments. Constraints on the hydrogenic ion temperatures and velocities based on measurements of the impurity ion properties are required to accurately fit the spectrum. Corrections for cross sectional distortions, spatial smearing due to the halo, and a neoclassical offset between the impurity and hydrogenic toroidal rotation are applied to the constraints prior to fitting the MICER spectrum. Extensive atomic physics calculations have been performed using the FIDASIM code, which has recently been improved to allow simulations using mixtures of hydrogenic species. Overall, these results demonstrate that for the same plasma parameters, the Dα emission is 20%–30% brighter than Hα due to differences in rate coefficients associated with the different ion thermal velocities for the same temperature and therefore must be taken into consideration when calculating absolute densities. However, despite these differences, the absolute error when estimating the hydrogen isotope fraction [n H /(n H + n D )] by using the Hα radiance fraction [L Hα /(L Hα + L Dα )] is typically less than 5% due to the way the fraction is formed, making the radiance fraction a reasonably accurate estimate of the isotope fraction for most cases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Charge exchange recombination spectroscopy measurements of DIII-D poloidal rotation with poloidal asymmetry in angular rotation

Sixteen new tangential views for the charge exchange recombination (CER) spectroscopy diagnostic at DIII-D were installed in 2019 on the high-field side (HFS) of the tokamak with the main goal being the measurement of main-ion (deuterium) poloidal rotation. Eight of the new views are connected to spectrometers, which view the main-ion spectrum, adding main-ion measurements where there were previously none, and another eight new views increased the spatial resolution of existing impurity (carbon) measurements on the HFS. When combined with the existing low-field side measurements, measurements at two locations on flux surfaces out to a normalized minor radius of ≈0.6 are possible. The new tangential views have been used to measure the deuterium poloidal rotation directly for the first time using the Poloidal Asymmetry in Angular Rotation (PAAR) method. Furthermore, these new measurements enable further testing of the validity of neoclassical poloidal rotation predictions. Separate measurements of the radial electric field can be made for an impurity ion and the main-ion by combining the PAAR measurements with additional CER measurements of toroidal rotation, temperature, and density. These independent measurements of the radial electric field agree reasonably well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Creation and sustainment of wide pedestal quiescent H-mode with zero net neutral beam torque

Recent experiments on DIII-D have shown it is possible to create and sustain wide pedestal quiescent H-mode (QH-mode) plasmas with zero net torque from neutral beam injection (NBI) for the full discharge duration. Wide pedestal QH-mode has many of the features of the previously investigated QH-mode while having the advantage of increased edge pedestal pressure and excellent energy confinement time. Both QH-mode variants operate without edge localized modes. Accordingly, these discharges demonstrate that significant input torque is not essential to the exploitation of wide pedestal QH-mode in future devices that are expected to have small or nonexistent NBI torque. In conclusion, developing operating conditions that allowed net zero torque access to wide pedestal QH-mode required implementing several techniques to avoid locked modes including minimizing intrinsic error fields, avoiding large sawteeth, and driving toroidal rotation via neoclassical toroidal viscosity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Predicting the rotation profile in ITER

Determining the toroidal rotation for future tokamaks like ITER is a challenging and important problem. By combining empirical scalings for the intrinsic rotation at the top of the pedestal with the expected neutral beam torque and modeling of momentum transport, the toroidal rotation profile for ITER is predicted with TGYRO using TGLF (SAT0 and SAT1). On axis rotation exceeds 20 krad s –1 and the E x B shear is significant enough to reduce turbulent transport and significantly increase confinement and fusion power when comparing to cases that ignore the effect of rotation. Here, the prediction of the rotation at the top of the pedestal is made with increased confidence due to experiments and modeling in DIII-D that have determined the importance of fast-ion and neutral particle transport effects on intrinsic rotation at this location. In particular, the effect of neutral particles on momentum transport in the pedestal region is found to be insignificant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗