Engineering Papers⌕ Search

Engineering topics

Harvey, W. D.

Publications and source records attributed to Harvey, W. D..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

NASA supercritical laminar flow control airfoil experiment

The design and goals of experimental investigations of supercritical LFC airfoils conducted in the NASA Langley 8-ft Transonic Pressure Tunnel beginning in March 1982 are reviewed. Topics addressed include laminarization aspects; flow-quality requirements; simulation of flight parameters; the setup of screens, honeycomb, and sonic throat; the design cycle; theoretical pressure distributions and shock-free limits; drag divergence and stability analysis; and the LFC suction system. Consideration is given to the LFC airfoil model, the air-flow control system, airfoil-surface instrumentation, liner design and hardware, and test options. Extensive diagrams, drawings, graphs, photographs, and tables of numerical data are provided.

Harvey, W. D.↗
NASA NTRS1982

NASA Langley laminar flow control airfoil experiment

The design and construction of an advanced swept supercritical airfoil for commercial aircraft to be tested in a transonic wind tunnel is described. The swept LFC airfoil was designed for a given thickness ratio and lift coefficient, with emphasis placed on high critical Mach number with shock-free flow. It is compatible with satisfactory low speed and buffeting characteristics and minimizing the suction laminarization. Further emphasis was placed on achieving shock-free flow over a wide range of off-design conditions including trailing edge flap control. The requirements and design of the suction system and modifications to the Langley 8 foot transonic pressure tunnel is briefly described. Contouring of nonporous test section walls for free air simulation and flow quality improvements is included.

Harvey, W. D.↗
NASA NTRS1982

The NASA Langley laminar flow control airfoil experiment

A large chord swept supercritical LFC airfoil has been constructed for NASA-Langley's research program to determine the compatibility of supercritical airfoils with suction laminarization and to establish a technology base for future transport designs. Features include a high design Mach number and shock-free flow, as well as the minimization of the laminarization suction through a choice of airfoil geometry and pressure distribution. Two suction surface concepts and a variety of hybrid suction concepts involving combinations of natural and forced laminar flow are to be investigated. The test facility has been modified to insure achievement of required flow quality and transonic interference-free flow over the yawed LFC airfoil.

Harvey, W. D.↗
NASA NTRS1981

Some anomalies between wind tunnel and flight transition results

A review of environmental disturbance influence and boundary layer transition measurements on a large collection of reference sharp cone tests in wind tunnels and of recent transonic-supersonic cone flight results have previously demonstrated the dominance of free-stream disturbance level on the transition process from the beginning to end. Variation of the ratio of transition Reynolds number at onset-to-end with Mach number has been shown to be consistently different between flight and wind tunnels. Previous correlations of the end of transition with disturbance level give good results for flight and large number of tunnels, however, anomalies occur for similar correlation based on transition onset. Present cone results with a tunnel sonic throat reduced the disturbance level by an order of magnitude with transition values comparable to flight.

Harvey, W. D.↗
NASA NTRS1980

Evaluation of flow quality in two large NASA wind tunnels at transonic speeds

Wind tunnel testing of low drag airfoils and basic transition studies at transonic speeds are designed to provide high quality aerodynamic data at high Reynolds numbers. This requires that the flow quality in facilities used for such research be excellent. To obtain a better understanding of the characteristics of facility disturbances and identification of their sources for possible facility modification, detailed flow quality measurements were made in two prospective NASA wind tunnels. Experimental results are presented of an extensive and systematic flow quality study of the settling chamber, test section, and diffuser in the Langley 8 foot transonic pressure tunnel and the Ames 12 foot pressure wind tunnel. Results indicate that the free stream velocity and pressure fluctuation levels in both facilities are low at subsonic speeds and are so high as to make it difficult to conduct meaningful boundary layer control and transition studies at transonic speeds.

Harvey, W. D.↗
NASA NTRS1979

Evaluation of flow quality in two NASA transonic wind tunnels

Tests have been conducted in the Langley Research Center 8-foot Transonic Pressure Tunnel and the Ames Research Center 12-foot pressure wind tunnel in order to measure characteristic disturbance levels and energy spectra in their respective settling chambers, test sections, and diffusers and to determine the sources of these disturbances. Results are presented and discussed along with some specific recommendations.

Owen, F. K.↗
NASA NTRS1978

Influence of free-stream disturbances on boundary-layer transition

Considerable experimental evidence exists which shows that free stream disturbances (the ratio of root-mean-square pressure fluctuations to mean values) in conventional wind tunnels increase with increasing Mach number at low supersonic to moderate hypersonic speeds. In addition to local conditions, the free stream disturbance level influences transition behavior on simple test models. Based on this observation, existing noise transition data obtained in the same test facility were correlated for a large number of reference sharp cones and flat plates and are shown to collapse along a single curve. This result is a significant improvement over previous attempts to correlate noise transition data.

Harvey, W. D.↗
NASA NTRS1976

Effect of slot width on transition and noise attenuation of a sound shield panel for supersonic wind tunnels

The effect of slot width on transition and noise attenuation of a planar rod wall sound shield has been investigated at Mach 6. Boundary layer laminarization was obtained by induced suction through adjustable slots or gaps between the rods. Transition Reynolds numbers increased significantly with increasing gap width. The local mean flow field above the suction panel rod array was uniform. Important factors for design and performance of a supersonic wind-tunnel sound shield are rod diameter, gap-to-rod diameter ratio, surface finish of the rods, and leading-edge configuration.

Harvey, W. D.↗
NASA NTRS1975

Effect of slot width on transition and noise attenuation of a flat sound shield in a Mach 6 wind tunnel

An experimental and theoretical study of a sound shield concept to attenuate the noise radiated into the test section from the turbulent boundary layer on the walls of wind tunnels was conducted. The model investigated was planar with a sharp flat plate leading edge faired into an array of rods aligned nearly parallel to the local flow. For a ratio of gap diameter to rod diameter of 0.16, the flow was laminar over the entire model at a maximum local length Reynolds number of 14 million. A 45% reduction in the tunnel free stream root mean square pressure level was measured within the shielded region for this gap width when the boundary layers on the rods were laminar. Smaller ratios of gap diameter to rod diameter resulted in substantial reductions in the transition Reynolds number, and in a 40% pressure reduction.

Stainback, P. C.↗
NASA NTRS1975

Wind tunnel blockage tests at Mach 5 of vacuum duct models for two sound radiation shields

Two sound shield models with dummy vacuum exhaust ducts were tested in a Mach 5 pilot quiet tunnel. The first model simulates a new sound shield of 3 in. (7.62 cm) inside diameter and the second model is a shield of 4 in. (10.16 cm) inside diameter. The dummy vacuum exhaust ducts were attached to the external housing of the models. The flow in the first model, which had a by pass mass flow ratio of about 0.6, could not be started except at the two highest test Reynolds numbers where only the central core flow region was started. The flow in the second model with a mass ratio of approximately 0.3 was fully started except at the lowest unit Reynolds number where some unsteadiness and partial flow separation at the wall was observed. Since the external housing and dummy vacuum ducts were the same for both models, these results indicate that the ratio of by pass mass flow to total mass flow for a wind tunnel sound shield of this particular design must be less than about 0.3. Hence, a lower limit is imposed on the inlet diameter of the sound shield in relation to the exit diameter of the wind tunnel nozzle. This lower limit on the inlet diameter may possibly be reduced by improvements in streamlining of the external housing and ducts, by reductions in blockage area, or by the use of external ducting shrouds.

Beckwith, I. E.↗
NASA NTRS1975

Design and preliminary test results at Mach 5 of an axisymmetric slotted sound shield

The basic theory and sound attenuation mechanisms, the design procedures, and preliminary experimental results are presented for a small axisymmetric sound shield for supersonic wind tunnels. The shield consists of an array of small diameter rods aligned nearly parallel to the entrance flow with small gaps between the rods for boundary layer suction. Results show that at the lowest test Reynolds number (based on rod diameter) of 52,000 the noise shield reduced the test section noise by about 60 percent ( or 8 db attenuation) but no attenuation was measured for the higher range of test reynolds numbers from 73,000 to 190,000. These results are below expectations based on data reported elsewhere on a flat sound shield model. The smaller attenuation from the present tests is attributed to insufficient suction at the gaps to prevent feedback of vacuum manifold noise into the shielded test flow and to insufficient suction to prevent transition of the rod boundary layers to turbulent flow at the higher Reynolds numbers. Schlieren photographs of the flow are shown.

Beckwith, I. E.↗
NASA NTRS1975

Effect of rod gap spacing on a suction panel for laminar flow and noise control in supersonic wind tunnels

Results are presented of a coordinated experimental and theoretical study of a sound shield concept which aims to provide a means of noise reduction in the test section of supersonic wind tunnels at high Reynolds numbers. The model used consists of a planar array of circular rods aligned with the flow, with adjustable gaps between them for boundary layer removal by suction, i.e., laminar flow control. One of the basic requirements of the present sound shield concept is to achieve sonic cross flow through the gaps in order to prevent lee-side flow disturbances from penetrating back into the shielded region. Tests were conducted at Mach 6 over a local unit Reynolds number range from about 1.2 x 10 to the 6th power to 13.5 x 10 to the 6th power per foot. Measurements of heat transfer, static pressure, and sound levels were made to establish the transition characteristics of the boundary layer on the rod array and the sound shielding effectiveness.

Harvey, W. D.↗
NASA NTRS1974

Experimental and theoretical investigation of a slotted noise shield model for wind tunnel walls

Tests at Mach 6 and 8 have been conducted on a model of a wind tunnel sound radiation shield which consists of interchangeable circular and wedge-shaped longitudinal rods with gaps between the rods for boundary layer removal. In view of the large effective sweep angle of the circular rods with respect to the local flow, the boundary layer behavior was surprisingly well represented by swept cylinder theory. Laminar flow was maintained up to a maximum local unit Reynolds number of 8 million per foot which would presumably be independent of model length for a given rod diameter by analogy with results on swept cylinders. Reduction in wind-tunnel sound levels within the shielded region of the circular rod model were about 90% of the maximum possible reduction for an ideal shield.

Harvey, W. D.↗
NASA NTRS1973

Control of supersonic wind-tunnel noise by laminarization of nozzle-wall boundary layer

One of the principal design requirements for a quiet supersonic or hypersonic wind tunnel is to maintain laminar boundary layers on the nozzle walls and thereby reduce disturbance levels in the test flow. The conditions and apparent reasons for laminar boundary layers which have been observed during previous investigations on the walls of several nozzles for exit Mach numbers from 2 to 20 are reviewed. Based on these results, an analysis and an assessment of nozzle design requirements for laminar boundary layers including low Reynolds numbers, high acceleration, suction slots, wall temperature control, wall roughness, and area suction are presented.

Beckwith, I. E.↗
NASA NTRS1972

Initial development of a hypersonic free mixing layer

A preliminary experimental investigation to establish some of the characteristics and further the understanding of the initial development of a turbulent free mixing layer for hypersonic speeds has been conducted. Mean profile data at about 6 inches downstream of the exit of a hypersonic nozzle have been obtained in nitrogen for a nominal Mach number of 19.5, total temperature of about 1670 K and Reynolds number range from about 50,000 to 110,000 per foot and have been compared with profiles upstream of the nozzle exit. Static pressure varied across the shear layer for the present tests. The outer 80 percent of the high-velocity portion of the free shear layer can be calculated by a rotational method of characteristics. However, turbulent mixing is evidently important in the low-velocity region, and effects of eddy viscosity and eddy conductivity should be included in a theoretical analysis.

Harvey, W. D.↗
NASA NTRS1972

Measurements of skin friction on the wall of a hypersonic nozzle.

Direct skin friction measurements obtained on the wall of a Mach 19.8 nozzle are presented. These measurements of skin friction and values deduced from the profile data are compared with predictions from a finite difference theory and also with several 'flat-plate' prediction methods for skin friction.

Harvey, W. D.↗