Engineering Papers⌕ Search

Engineering topics

Hartwich, Peter M.

Publications and source records attributed to Hartwich, Peter M..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Development of an Active Flow Control Technique for an Airplane High-Lift Configuration

This study focuses on Active Flow Control methods used in conjunction with airplane high-lift systems. The project is motivated by the simplified high-lift system, which offers enhanced airplane performance compared to conventional high-lift systems. Computational simulations are used to guide the implementation of preferred flow control methods, which require a fluidic supply. It is first demonstrated that flow control applied to a high-lift configuration that consists of simple hinge flaps is capable of attaining the performance of the conventional high-lift counterpart. A set of flow control techniques has been subsequently considered to identify promising candidates, where the central requirement is that the mass flow for actuation has to be within available resources onboard. The flow control methods are based on constant blowing, fluidic oscillators, and traverse actuation. The simulations indicate that the traverse actuation offers a substantial reduction in required mass flow, and it is especially effective when the frequency of actuation is consistent with the characteristic time scale of the flow.

Shmilovich, Arvin↗
NASA NTRS2016

Refined AFC-Enabled High-Lift System Integration Study

A prior trade study established the effectiveness of using Active Flow Control (AFC) for reducing the mechanical complexities associated with a modern high-lift system without sacrificing aerodynamic performance at low-speed flight conditions representative of takeoff and landing. The current technical report expands on this prior work in two ways: (1) a refined conventional high-lift system based on the NASA Common Research Model (CRM) is presented that is more representative of modern commercial transport aircraft in terms of stall characteristics and maximum Lift/Drag (L/D) ratios at takeoff and landing-approach flight conditions; and (2) the design trade space for AFC-enabled high-lift systems is expanded to explore a wider range of options for improving their efficiency. The refined conventional high-lift CRM (HL-CRM) concept features leading edge slats and slotted trailing edge flaps with Fowler motion. For the current AFC-enhanced high lift system trade study, the refined conventional high-lift system is simplified by substituting simply-hinged trailing edge flaps for the slotted single-element flaps with Fowler motion. The high-lift performance of these two high-lift CRM variants is established using Computational Fluid Dynamics (CFD) solutions to the Reynolds-Averaged Navier-Stokes (RANS) equations. These CFD assessments identify the high-lift performance that needs to be recovered through AFC to have the CRM variant with the lighter and mechanically simpler high-lift system match the performance of the conventional high-lift system. In parallel to the conventional high-lift concept development, parametric studies using CFD guided the development of an effective and efficient AFC-enabled simplified high-lift system. This included parametric trailing edge flap geometry studies addressing the effects of flap chord length and flap deflection. As for the AFC implementation, scaling effects (i.e., wind-tunnel versus full-scale flight conditions) are addressed, as are AFC architecture aspects such as AFC unit placement, number AFC units, operating pressures, mass flow rates, and steady versus unsteady AFC applications. These efforts led to the development of a novel traversing AFC actuation concept which is efficient in that it reduces the AFC mass flow requirements by as much as an order of magnitude compared to previous AFC technologies, and it is predicted to be effective in driving the aerodynamic performance of a mechanical simplified high-lift system close to that of the reference conventional high-lift system. Conceptual system integration studies were conducted for the AFC-enhanced high-lift concept applied to a NASA Environmentally Responsible Aircraft (ERA) reference configuration, the so-called ERA-0003 concept. The results from these design integration assessments identify overall system performance improvement opportunities over conventional high-lift systems that suggest the viability of further technology maturation efforts for AFC-enabled high lift flap systems. To that end, technical challenges are identified associated with the application of AFC-enabled high-lift systems to modern transonic commercial transports for future technology maturation efforts.

Hartwich, Peter M.↗
NASA NTRS2014

AFC-Enabled Simplified High-Lift System Integration Study

The primary objective of this trade study report is to explore the potential of using Active Flow Control (AFC) for achieving lighter and mechanically simpler high-lift systems for transonic commercial transport aircraft. This assessment was conducted in four steps. First, based on the Common Research Model (CRM) outer mold line (OML) definition, two high-lift concepts were developed. One concept, representative of current production-type commercial transonic transports, features leading edge slats and slotted trailing edge flaps with Fowler motion. The other CRM-based design relies on drooped leading edges and simply hinged trailing edge flaps for high-lift generation. The relative high-lift performance of these two high-lift CRM variants is established using Computational Fluid Dynamics (CFD) solutions to the Reynolds-Averaged Navier-Stokes (RANS) equations for steady flow. These CFD assessments identify the high-lift performance that needs to be recovered through AFC to have the CRM variant with the lighter and mechanically simpler high-lift system match the performance of the conventional high-lift system. Conceptual design integration studies for the AFC-enhanced high-lift systems were conducted with a NASA Environmentally Responsible Aircraft (ERA) reference configuration, the so-called ERA-0003 concept. These design trades identify AFC performance targets that need to be met to produce economically feasible ERA-0003-like concepts with lighter and mechanically simpler high-lift designs that match the performance of conventional high-lift systems. Finally, technical challenges are identified associated with the application of AFC-enabled highlift systems to modern transonic commercial transports for future technology maturation efforts.

Hartwich, Peter M.↗
NASA NTRS1998

Preliminary Evaluation of Nonlinear Effects on TCA Flutter

The objective of this study is to investigate the effect of nonlinear aerodynamics, especially at high angles-of-attack with leading-edge separation, on the TCA flutter properties at transonic speeds. In order to achieve that objective, flutter simulations with Navier-Stokes CFD must be performed. To this end, time-marching Navier-Stokes solutions are computed for the TCA wing/body configuration at high angles-of-attack in transonic flight regimes. The approach is to perform non-linear flutter calculations on the TCA at two angles-of-attack, the first one being a case with attached flow (a=2.8 degrees) and the second one being a high angle-of-attack case with a wing leading edge vortex (a=12.11 degrees). Comparisons of the resulting histories and frequency damping information for both angles-of-attack will evaluate the impact of high-alpha aerodynamics on flutter.

Arslan, Alan E.↗
NASA NTRS1996

Effect of Full-Chord Porosity on Aerodynamic Characteristics of the NACA 0012 Airfoil

A test was conducted on a model of the NACA 0012 airfoil section with a solid upper surface or a porous upper surface with a cavity beneath for passive venting. The purposes of the test were to investigate the aerodynamic characteristics of an airfoil with full-chord porosity and to assess the ability of porosity to provide a multipoint or self-adaptive design. The tests were conducted in the Langley 8-Foot Transonic Pressure Tunnel over a Mach number range from 0.50 to 0.82 at chord Reynolds numbers of 2 x 10(exp 6), 4 x 10(exp 6), and 6 x 10(exp 6). The angle of attack was varied from -1 deg to 6 deg. At the lower Mach numbers, porosity leads to a dependence of the drag on the normal force. At subcritical conditions, porosity tends to flatten the pressure distribution, which reduces the suction peak near the leading edge and increases the suction over the middle of the chord. At supercritical conditions, the compression region on the porous upper surface is spread over a longer portion of the chord. In all cases, the pressure coefficient in the cavity beneath the porous surface is fairly constant with a very small increase over the rear portion. For the porous upper surface, the trailing edge pressure coefficients exhibit a creep at the lower section normal force coefficients, which suggests that the boundary layer on the rear portion of the airfoil is significantly thickening with increasing normal force coefficient.

Mineck, Raymond E.↗
NASA NTRS1994

Comparison of coordinate-invariant and coordinate-aligned upwinding for the Euler equations

A floating-shock fitting method for the Euler equations has been developed that uses one-sided spatial differences along and across streamlines. The coordinate-invariant formulation of the spatial differences permits automatic capture of shears. Results are presented for unsteady shocked flow in a duct with a ramp, for supercritical flow over a circular cylinder, and for subsonic, transonic, and supersonic (0.3 is less than or equal to M(sub infinity) is less than 1.5) flow over airfoils. In flows with strong shears, the coordinate-invariant differencing concept appears to yield some gains in accuracy over Euler methods that rely on coordinate-aligned differencing concepts. In applications to transonic airfoils, fitted shocks have a tendency to be predicted upstream of captured shocks, regardless of whether coordinate-invariant or coordinate-aligned differencing is used. The coordinate-invariant differencing method requires between 2 and 3.5 times as much computing time as its coordinate-aligned counterpart.

Hartwich, Peter M.↗
NASA NTRS1994

Symmetry breaking in vortical flows over cones -- theory and numerical experiments

A stability analysis suggests that inviscid incompressible flow, independent from angle of attack and regardless whether attached or separated, over slender cones is only marginally stable in regions of decelerating circumferential flow. Reducing slenderness or surface curvature lowers the frequency spectrum of the harmonic perturbations and, thus, reduces their impact on the overall stability of flows over slender cones. Associating the notion of instabilities in such flows with the onset of vortex asymmetries provides a model for explaining a variety of flow phenomena in Navier-Stokes simulations of laminar incompressible flows over three right circular cones at moderate to high angles of attack.

Hartwich, Peter M.↗
NASA NTRS1993

Symmetry breaking in vortical flows over cones - Theory and numerical experiments

A stability analysis suggests that inviscid incompressible flow, independent from angle of attack and regardless whether attached or separated, over slender cones is only marginally stable in regions of decelerating circumferential flow. Reducing slenderness or surface curvature lowers the energy level of harmonic perturbations, and, thus, reduces their impact on the overall stability of flows over slender cones. Associating the notion of instabilities in such flows with the onset of vortex asymmetries provides a model for explaining a variety of flow phenomena in Navier-Stokes simulations of laminar incompressible flows over three right circular cones at moderate to high angles of attack.

Hartwich, Peter M.↗
NASA NTRS1993

Comparison of coordinate-invariant and coordinate-aligned upwinding for the Euler equations

A floating-shock fitting method for the Euler equations has been developed that uses one-sided spatial differences along and across streamlines. This method has been applied to unsteady shocked flow in a duct with a ramp, to supercritical flow over a circular cylinder, and to transonic flow over airfoils. Compared to methods using coordinate-aligned upwind differencing, the coordinate-invariant upwinding generally required fewer grid points to produce crisp shocks and shears. For transonic airfoils, coordinate-invariant upwind differencing advances the agreement between computations and experiment, and it reduces the grid dependency of the computed results for strong shocks. The computational expenditure is comparable to that of coordinate-aligned upwind methods for the Euler equations.

Hartwich, Peter M.↗
NASA NTRS1992

Porous airfoil and process

A porous airfoil having venting cavities with contoured barrier walls, formed by a core piece, placed beneath a porous upper and lower surface area that stretches over the nominal chord of an airfoil is employed, to provide an airfoil configuration that becomes self-adaptive to very dissimilar flow conditions to thereby improve the lift and drag characteristics of the airfoil at both subcritical and supercritical conditions.

Hartwich, Peter M.↗
NASA NTRS1992

Estimation of propulsion-induced effects on transonic flows over a hypersonic configuration

Boundary conditions are formulated for treating selected patches of a subject configuration as inlet or nozzle areas. For subsonic inflow, the mass flow through the inlet is controlled by the exhaust conditions and the effects of mass and heat addition. For supersonic inflow, the exhaust conditions are based on the inlet conditions and on combustion data. These formulations were included into an existing Euler/Navier-Stokes solver. Comparisons with experimental data demonstrate that the resulting software package efficiently permits the assessment of propulsion-induced effects on external flow fields, particularly around highly blended configurations.

Hartwich, Peter M.↗
NASA NTRS1992

Navier-Stokes analyses of flows over slender airframes

An account is given of the current development status of Navier-Stokes algorithms for the analysis of 3D viscous flows over slender airframes, emphasizing the design and analysis of practical configurations. The pacing items of the numerical algorithms used encompass grid generation, spatial and temporal differencing, and transition and turbulence modeling. Attention is given to the high angle-of-attack prediction capability of the various methods whose results are compared with experimental data; it is in that regime that Navier-Stokes methods surpass the prediction capabilities of flow solvers based on simpler mathematical models.

Thomas, James L.↗
NASA NTRS1991

Euler study on porous transonic airfoils with a view toward multipoint design

Euler solutions for steady transonic flow (Free-stream Mach 0.63-0.8, alpha = 0-2 deg) over NACA 0012 and supercritical airfoils with solid as well as porous surfaces suggest porosity as a means to realize multipoint design for transonic airfoils. The porous surfaces extend over at least 90 percent of the chord. The porosity distribution is described by a modified sine wave with several amplitudes. Either connected or separated cavities are assumed to lie underneath the upper and lower surfaces. Applied to an NACA 0012 airfoil, porosity generally increases lift, in some instances by up to 65 percent. Porous NACA 0012 airfoils in supercritical flow yield reductions of an order of magnitude in wave drag at constant lift, compared to their solid counterpart. Making the surface of a supercritical airfoil permeable also leads to sizeable reductions in wave drag at constant lift for overspeed conditions. The discussion of the computed results addresses issues such as grid sensitivity and checks for systematic errors.

Hartwich, Peter M.↗
NASA NTRS1988

Aerodynamic applications of an efficient incompressible Navier-Stokes solver

A robust and accurate upwind scheme based on flux-difference splitting for three-dimensional, incompressible flows in general coordinates is described. Viscous effects are included through a thin-layer approximation to the Navier-Stokes equations. Turbulent flows are simulated with extensions to the Baldwin-Lomax (1978) turbulence model. The effects of accuracy and gridding on the computed flow field results are assessed. The results obtained from the code for vortical flows over a delta wing, a double delta wing, and a tangent-ogive forebody compare well with experimental data.

Hartwich, Peter M.↗