Engineering topics

Hartley, Damon S.

Publications and source records attributed to Hartley, Damon S..

24 records · Page 2

DOE OSTI2022

Particle scale impacts on deconstruction energy of pine residues

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on generation of fines that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbon content (minimum carbon specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed residue not meeting both specifications to the conversion reactor. Laboratory data on the impacts of input particle size and moisture content on the exit particle size were received from FCIC Subtask 5.2 from their single particle impact population balance modeling study. Additional throughput and energy consumption data were obtained from FCIC Subtask 5.2 for the same grinder with a 6 mm screen in place. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents in the separated fines had not been analyzed in the laboratory at the time of the model runs, we chose to assume that the ash distributed proportionally with total mass into the overs and unders in the disk screen following grinding. Key takeaways from this Case Study are that it is significantly more cost effective to hammer mill the residue prior to drying, even though the grinder throughput is lower and energy consumption is higher versus drying first before grinding. An effect of dry grinding versus high moisture grinding is the production of higher amounts of fines during dry grinding, leading to significantly more of the ground feedstock being rejected by conversion for being below a minimum particle size. With wet grinding the system is still able to produce more preprocessed feedstock meeting the minimum particle size specification even though the instantaneous throughput is lower than for the case of grinding dry feedstock. Additionally, even without the higher fines production from dry grinding, the status quo would still be more costly than wet grinding because the material is rejected after the drying energy has already been input for the dry grinding case. Finally, significant reductions in drying energy are obtained by drying after grinding, and those reductions are of far greater magnitude than the grinding energy increase.

09 BIOMASS FUELS↗

DOE OSTI2022

Air classification of forest residue for tissue and ash separation efficiency

The goal of this Case Study was to evaluate the performance of air classification of logging residues toward meeting conversion CMAs for carbon and ash contents, as compared to the static status quo Base Case system in which the residues are first dried and then ground in a hammer mill with a 6 mm screen and fines < 1.18 mm are removed. Also considered were moisture and ash impacts on throughput and Overall Operating Effectiveness (OOE), as well as delivered feedstock cost and minimum fuel selling price (MFSP). Laboratory data on the impacts of fan speed and moisture content on the separation efficiency of soil ash, needles and bark from white wood were received from FCIC Subtask 5.2. Average throughput and energy consumption data were obtained from the Bioenergy Feedstock National User Facility (BFNUF) for the same air classifier. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the Base Case status quo system utilizes drying prior to grinding, we modeled the Case Study with drying prior to air classification and subsequent grinding of the separated white wood to isolate the individual quality and cost impacts of air classification relative to the Base Case system. Key takeaways from this Case Study are that air classification improves the quality of the final material, but increases the production cost, especially when lights are disposed; this becomes a tradeoff between increased conversion yield and the extra cost. Removing material should be done as early in the process as possible. Each operation that occurs prior to removing the material increases the cost of the disposed material and leads to wasted energy expenditures. As processes are included or modified, the impact on monetary and energy cost should be included in the decision process. Identifying alternative uses and the associated value for material that is separated from the feedstock stream will have a significant impact on the delivered cost of the material. Although there was an increase in production cost by adding air classification, there was a resulting benefit to the MFSP when meeting or exceeding all of the conversion CMAs; this was an important finding that should be explored further with FCIC Subtask 8.3 and potentially FCIC Task 6.

09 BIOMASS FUELS↗

DOE OSTI2022

Material Flow Analysis and Life Cycle Assessment of Polyethylene Terephthalate and Polyolefin Plastics Supply Chains in the United States

Plastics are useful and beneficial materials that contribute to an improved quality of life, yet they generate significant solid wastes and emissions and consume significant energy resources. Systems analysis is incomplete on current linear production systems of plastics supply chains and their associated processes. Our study combines material flow and life cycle assessment data sets of polyethylene terephthalate (PET) and the main polyolefin polymers in the United States, comprising over 70% of plastics flows. This study estimates the total greenhouse gas (GHG) emissions and energy consumption of these supply chains, including transportation and end-of-life processes, lacking in prior studies. Here we calculate annual GHG emissions and energy consumption of these plastic supply chains to be 101 MMT CO 2 -eq and 3248 PJ in 2019, respectively. The GHG emissions of these supply chains represented 1.5% of the total U.S. emissions and 5% of the total U.S. industry-related GHG emissions. The total energy consumption of these supply chains represented 3.1% of the total U.S. energy consumption in 2019. Transportation of PET and polyolefin plastic materials contributes 5% and 2% to the total supply chain GHG emissions and energy consumption, respectively. This baseline study provides a benchmark and enables a comparison to future circular production systems for plastics in the United States.

09 BIOMASS FUELS↗

DOE OSTI2022

Nth-plant scenario for forest resources and short rotation woody crops: Biorefineries and depots in the contiguous US

Estimating the US potential of woody material is of vital importance to ensure cost-effective supply logistics and develop a sustainable bioenergy and bioproducts industry. We analyzed a mature conversion technology for woody resources for the contiguous US that takes advantage of economies of scale: the nth-plant. Here, we developed a database to quantify the total accessible woody biomass within a distributed network of preprocessing depots and biorefineries considering both quality specifications for conversion and a target cost to compete with fossil fuels. We considered two categories of woody biomass: 1) forest residues from trees, tops and limbs produced from conventional thinning and timber harvesting operations as well as non-timber tree removal; and 2) short rotation woody crops such as poplar, willow, pine, and eucalyptus. A mixed integer linear programming model was developed to analyze scenarios with woody feedstock blends at variable biomass ash contents and cost targets at the biorefinery. When considering a target cost of 85.51 dollars/dry ton (2016$) at the biorefinery, the maximum accessible biomass from forest residues in 2040 remained constant at 106 million dry tons regardless of ash targets. Including short rotation woody crops as part of the blend increased the total accessible biomass to 153 and 195 million dry tons at ash targets of 1% and 1.75%, respectively. We concluded from our analysis that woody resources could address about 55% of EPA’s (Environmental Protection Agency) target of 16 billion gallons of cellulosic biofuel.

09 BIOMASS FUELS↗

DOE OSTI2022

Model quantification of the effect of coproducts and refinery co-hydrotreating on the economics and greenhouse gas emissions of a conceptual biomass catalytic fast pyrolysis process

Here we present model results for a scaled-up conceptual process informed by bench scale biomass catalytic fast pyrolysis (CFP) and hydrotreating experimental data. This process uses a Pt/TiO 2 catalyst during CFP, which produces a partially deoxygenated organic biocrude intermediate that is then hydroprocessed to a hydrocarbon fuel blendstock; the catalyst also enables high yields of acetone and methyl-ethyl-ketone (MEK) coproducts. Two options for hydroprocessing were modeled: (A) co-hydrotreating at a petroleum refinery using hydrogen sourced from steam reforming of natural gas and (B) standalone hydrotreating at a biorefinery using hydrogen sourced from CFP off gases. The results revealed that Case A was economically advantageous with a modeled minimum fuel selling price (MFSP) of $\$$2.83/GGE or gallon gasoline equivalent (in 2016 US dollars), while the additional cost of standalone hydrotreating facilities in Case B increased the MFSP to $3.13/GGE. Conversely, greenhouse gas (GHG) emissions were lower for Case B (3.9 g CO 2 e/MJ) compared to Case A (21.5 g CO 2 e/MJ) due to the use of biogenic (Case B) and fossil-derived (Case A) hydrogen. In a third option (Case C), the requirements for separation and purification of acetone and MEK were removed from the refinery co-processing scenario (Case A) to evaluate the impacts of this process simplification. Elimination of these coproducts increased the MFSP to $3.21/GGE and GHG emissions to 35 g CO 2 e/MJ. These comparisons based on our detailed conceptual models provide economic and sustainability guidance regarding processing choices for future biorefineries. While refinery coprocessing using existing equipment and the production of relatively valuable coproducts can benefit the economics, the hydrogen-source and biogenic coproducts can have significant impacts on the sustainability of the process, and feasibility to use CFP off-gases or other renewable sources for hydrogen production can help lower GHG emissions.

09 BIOMASS FUELS↗

DOE OSTI2022

Evaluation of artificial neural network performance for classification of potato plants infected with potato virus Y using spectral data on multiple varieties and genotypes

Potato virus Y (Potyviridae, PVY) is a plant virus that poses a significant threat to potato producers on a global basis. The pathogen has disrupted seed potato supplies and negatively impacted yield and quality of commercial potato crops. The potato industry currently manages PVY infection levels via insecticide applications, regional seed certification programs that rely on field scouting to visually assess individual plants for infection status, and destructive and costly tissue sampling coupled with laboratory assays. Despite these efforts, PVY continues to confound potato industry stakeholders resulting in economic harm. Remote sensing and machine learning provide for the development of new tools to more accurately detect and spatially quantify PVY-infected plants versus the current state of the art. However, there is a need to understand how the occurrence of many different potato varieties impact the dynamics of developing models to detect potato plants impacted with PVY and their potential effectiveness. This study evaluates classification modelling outcomes using spectral datasets collected in different temporal and spatial environments (greenhouse and a production field) on multiple potato varieties consisting of labelled instances of plants infected with PVY and those not infected with the virus. A modelling framework was developed to support iterative modelling runs using artificial neural network (ANN) architectures configured as binary classifiers to develop sample populations to support statistical analysis on model performance using specific spectral subsets. When using spectral data to detect PVY-infected plants, ANN models achieved the highest mean accuracy of 0.894 on a single variety. Conversely, the same ANN model architecture only achieved a mean accuracy of 0.575 on a spectral data set representing 29 potato breeding lines. Additionally, statistical analysis indicates spectral regions including the red edge, near infrared and shortwave infrared contain more important spectral features for the ANN classifier introduced in this research.

60 APPLIED LIFE SCIENCES↗