Engineering Papers⌕ Search

Engineering topics

Harris, James W.

Publications and source records attributed to Harris, James W..

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Understanding_the_deactivation_mechanisms_of_ethanol_conversion_over_Cu-Y_Beta_catalyst

Direct conversion of bioethanol to C₃⁺olefins is a promising pathway for sustainable aviation fuel (SAF) production, but catalyst deactivation limits long-term operation. The stability and deactivation mechanisms of multifunctional Cu–Y/Beta zeolite catalysts were investigated for ethanol-to-olefins conversion over 300 h time-on-stream in the presence of H2. Catalytic testing reveals progressive losses in ethanol conversion and C₃⁺ olefin selectivity accompanied by increased acetaldehyde formation. The catalyst testing studies correlate with a suite of characterizations of fresh, spent, and regenerated catalysts to identify the deactivation factors. The loss of Y Lewis acid sites is the primary deactivation element. Reversible acid site deactivation is caused by coke deposition, which blocks Y-derived Lewis acid sites responsible for aldol condensation, MPV reduction, and alcohol dehydration. Minor irreversible deactivation is observed and possibly results from hydrothermal dehydroxylation of Y–silanol interactions, resulting in permanent loss of Lewis acidity without zeolite framework degradation or Y aggregation. Cu sites undergo limited agglomeration into small nanoparticles but contribute insignificantly to catalyst deactivation, under the investigated time frame. Oxidative regeneration removes coke and redistributes Cu sites, leading to full recovery of the initial catalytic performance though the Y Lewis acid sites are unable to fully recover. These findings establish Lewis acid site degradation as the primary deactivation mechanism impacting long-term catalyst stability

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impact of Particle Size on the Vapor-Phase Oxidative Coupling of Methanol and Dimethylamine over Palladium–Gold Nanoparticles

Oxidative coupling of methanol and dimethylamine in the presence of O 2 in the vapor phase over dilute Pd in Au bimetallic catalysts occurs via the dissociation of O 2 on Pd and selective oxidation of methanol on Au. Here, we synthesize a series of silica-supported PdAu alloy nanoparticle catalysts of varied Pd:Au ratios with ~5 nm particle diameter and show that these catalysts have increased selectivity to dimethylformamide across all Pd:Au ratios (~95%), distinct from observations over larger PdAu nanoparticles (~15–25 nm diameter) of similar Pd:Au ratios. Small monometallic Pd particles are more selective than large monometallic Pd particles, and small Au nanoparticles are reactive and selective for oxidative coupling (while large Au nanoparticles are inactive). Rates per surface metal atom were similar over PdAu nanoparticles of all sizes and increased monotonically with increasing Pd content for the small nanoparticles. Further, apparent reaction kinetics demonstrate distinct apparent methanol reaction order and apparent activation energy relative to those reported over larger nanoparticles of similar Pd:Au ratios. Unlike larger PdAu nanoparticles, the rate of dimethylformamide formation is not promoted by cofed water over small PdAu nanoparticles. The results of the kinetic studies are used to propose a series of elementary steps, derive a plausible rate expression, and regress rate and equilibrium constants. These results suggest high coverages of surface methoxy species and low coverages of adsorbates derived from dimethylamine. Taken together, these results demonstrate the sensitivity of the rates, selectivities, and kinetics of oxidative coupling reactions to the size of bimetallic nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Quantification of active sites in yttrium containing dealuminated Beta zeolites during conversion of ethanol and acetaldehyde to butadiene

Here, in this work, yttrium containing dealuminated Beta zeolites (Y/deAlBeta) were synthesized and characterized by various spectroscopic techniques to improve understanding of ethanol upgrading over these materials. Characterization results indicate yttrium atoms partially condense with framework silanol nests formed during dealumination of parent Al-Beta supports. Active sites for conversion of ethanol and acetaldehyde to butadiene were quantified on a series of Y/deAlBeta catalysts (0.1–10 wt% yttrium) via ex situ chemisorption and transmission Fourier transformed infrared (FTIR) spectroscopy measurements by first measuring the integrated molar extinction coefficient (IMEC) for pyridine bound to Lewis acidic yttrium sites. In situ titrations with pyridine demonstrate that the number of sites quantified by ex situ chemisorption IR is quantitatively similar to the number of sites that catalyze butadiene formation, which varies (from 0.05 to 0.35) across the series of catalysts. In situ pyridine titrations impact butadiene site time yields (STY), but not crotonaldehyde STY, indicating that a distribution of yttrium sites is present, and that discrete yttrium site types participate in distinct steps in the pathway from ethanol to butadiene. Apparent kinetic parameters including activation energies and reaction orders were measured, these suggest differences in reactant (or reactant-derived intermediate) surface coverages result in higher STYs (per mol Y or per Lewis acidic Y site) for samples with low Y loadings relative to those with higher Y loadings. Isotopic labeling experiments evince the existence of other kinetically relevant steps in addition to the crotonaldehyde transformation to crotyl alcohol. Together, these findings provide further guidance into the heterogeneities in site structures in yttrium-containing zeolites and their relevance for the various steps in the pathway from ethanol to C 4 products useful for production of sustainable aviation fuel and renewable butadiene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Recommendations for improving rigor and reproducibility in site specific characterization

Heterogeneous catalysis is driven by the interaction of reactant molecules and the catalyst surface. The locus of this interaction as well as the surrounding ensemble of atoms is referred to as the catalyst active site. Active site characterization attempts to distinguish active catalytic sites from inactive surface sites, to elucidate the structural and chemical nature of active sites, and to quantify active site concentration. Numerous techniques have been demonstrated to provide compositional and structural information about the active sites within a catalyst. However, each technique has its own limitations and experimental pitfalls that can lead to data misinterpretation or irreproducible results. Further, this work aims to provide an overview of the types of data that can be collected, to outline common experimental challenges and how to avoid them, and to assemble relevant references for the most used active site characterization techniques. More broadly, we aim to outline best practices for researchers to collect, interpret, and report active site characterization data in a way that provides the most benefit to the broader catalysis community. Increasing the rigor and reproducibility of active site characterization offers a strategy to better link properties with catalytic performance and to enable the community to develop consensus concerning these relationships.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Dynamic Copper Site Redispersion through Atom Trapping in Zeolite Defects

Single-site copper-based catalysts have shown remarkable activity and selectivity for a variety of reactions. However, deactivation by sintering in high-temperature reducing environments remains a challenge and often limits their use due to irreversible structural changes to the catalyst. Here, we report zeolite-based copper catalysts in which copper oxide agglomerates formed after reaction can be repeatedly redispersed back to single sites using an oxidative treatment in air at 550 °C. Under different environments, single-site copper in Cu–Zn–Y/deAlBeta undergoes dynamic changes in structure and oxidation state that can be tuned to promote the formation of key active sites while minimizing deactivation through Cu sintering. For example, single-site Cu 2+ reduces to Cu 1+ after catalyst pretreatment (270 °C, 101 kPa H 2 ) and further to Cu0 nanoparticles under reaction conditions (270–350 °C, 7 kPa EtOH, 94 kPa H 2 ) or accelerated aging (400–450 °C, 101 kPa H 2 ). After regeneration at 550 °C in air, agglomerated CuO was dispersed back to single sites in the presence and absence of Zn and Y, which was verified by imaging, in situ spectroscopy, and catalytic rate measurements. Ab initio molecular dynamics simulations show that solvation of CuO monomers by water facilitates their transport through the zeolite pore, and condensation of the CuO monomer with a fully protonated silanol nest entraps copper and reforms the single-site structure. Importantly, the capability of silanol nests to trap and stabilize copper single sites under oxidizing conditions could extend the use of single-site copper catalysts to a wider variety of reactions and allows for a simple regeneration strategy for copper single-site catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Investigation of Cu Species in Dealuminated Beta Zeolite Studied by Operando Closed-Cell Gas Reaction STEM

Direct conversion of ethanol to C3+ olefins is an attractive pathway to produce sustainable aviation fuels [1]. We recently reported a copper-containing catalyst supported on dealuminated (DeAl) beta zeolite that is capable of catalyzing cascade ethanol to olefins reactions with high olefins selectivity (88% C3+ olefin selectivity at 100% ethanol conversion). However, one of the deactivation mechanisms of the catalyst is copper sintering [2]. It was found that copper agglomerates can be redispersed through a simple oxidative treatment. To better understand the kinetics and process conditions conducive to redispersion, we studied the atmosphere and temperature dependent Cu species in Cu/DeAl-Beta catalyst under conditions matching those of the working catalyst.

beta zeolite↗
DOE OSTI2022

Ethanol Conversion to C 4+ Olefins over Bimetallic Copper- And Lanthanum-Containing Beta Zeolite Catalysts

We report ethanol conversion to C 4+ olefins remains a critical yet nonselective process for producing renewable middle distillates. Here, Cu–La/Beta catalysts composed of copper and lanthanum incorporated onto a dealuminated Beta support are reported for ethanol conversion to C 4+ olefins (73% selectivity, ~98% ethanol conversion, 623 K,<4% C 1 –C 3 hydrocarbons) which particularly favors C 5+ olefin formation (43% selectivity) as a distinction from the benchmarking Cu–Y/Beta catalyst. Monometallic Cu/Beta or La/Beta samples are insufficient to catalyze the C 4+ olefin formation and primarily form dehydration products (e.g., ethylene and diethyl ether), indicating the necessity of both Cu and La species for butene and C 5+ olefin formation. Increasing the bulk La loading at a fixed Cu content yields higher C 5+ olefins until the La/Cu molar ratio reaches 3.6. These findings indicate Cu–La/Beta as an effective ethanol conversion catalyst that facilitates multiple C–C bond formation events required for synthesizing C 5+ olefins (i.e., hexenes and octenes).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Isolated Metal Sites in Cu–Zn–Y/Beta for Direct and Selective Butene-Rich C 3+ Olefin Formation from Ethanol

Direct and selective production of C 3+ olefins from bioethanol remains a critical challenge and important for the production of renewable transportation fuels such as aviation biofuels. In this study, we report a Cu–Zn–Y/Beta catalyst for selective ethanol conversion to butene-rich C 3+ olefins (88% selectivity at 100% ethanol conversion, 623 K), where the Cu, Zn, and Y sites are all highly dispersed. The ethanol-to-butene reaction network includes ethanol dehydrogenation, aldol condensation to crotonaldehyde, and hydrogenation to butyraldehyde, followed by further hydrogenation and dehydration reactions to form butenes. Cu sites play a critical role in promoting hydrogenation of the crotonaldehyde C═C bond to form butyraldehyde in the presence of hydrogen, making this a distinctive pathway from crotyl alcohol-based ethanol-to-butadiene reaction. Reaction rate measurements in the presence of ethanol and acetaldehyde (543 K, 12 kPa ethanol, 1.2 kPa acetaldehyde, 101.9 kPa H 2 ) over monometallic Zn/Beta and Y/Beta catalysts indicate that Y sites have higher C–C coupling rates than over Zn sites (initial C–C coupling rate, 6.1 × 10 –3 mol mol Y –1 s –1 vs 1.2 × 10 –3 mol mol Zn –1 s –1 ). Further, Lewis-acidic Y-site densities over Cu–Zn–Y/Beta with varied Y loadings are linearly correlated with the initial C–C coupling rates, suggesting that Lewis-acidic Y sites are the predominant sites that catalyze C–C coupling in Cu–Zn–Y/Beta catalysts. Control experiments show that the dealuminated Beta support is important to form higher density of Lewis-acidic Y sites in comparison with other supports such as silica, or deboronated MWW despite similar atomic dispersion of Y sites and Y–O coordination numbers over these supports, leading to more than 9 times higher C–C coupling rate per mole Y over dealuminated Beta relative to other supports. This study highlights the significance of unique combination of metal sites in contributing to the selective valorization of ethanol to C 3+ olefins, motivating for exploring multifunctional zeolite catalysts, where the presence of multiple sites with varying reactivities and functions allows for controlling the predominant molecular fluxes toward the desired products in complex reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Consequences of product inhibition in the quantification of kinetic parameters

While the potential for product inhibition in catalytic reactions is well known, the impact of neglected inhibition on measured kinetic parameters is often overlooked. The presence of product inhibition, most often caused by the competitive adsorption of products with reactants on catalytic active sites, is difficult to determine a priori for an arbitrary catalytic system. The significance of product inhibition relies on the concentration of the products, their adsorption thermodynamics on catalytically relevant sites, and process parameters such as temperature and pressure. When inhibition is significant, however, apparent activation energies and reaction orders vary from the differential-reactor apparent activation energy by a factor of 1/(1 - δ), where δ is the total inhibition order (e.g., the factor (1 - δ) = 1.6 for a system with product inhibition of -0.6 order). This is illustrated here with the kinetics of NO oxidation over Cu ion clusters (Cu x O y ) in Cu-SSZ-13, for which the product NO 2 inhibits the forward reaction. Furthermore, in the presence of inhibition, when only reactants are fed to a flow reactor or placed in a batch reactor, there is often no practical conversion that is low enough to guarantee differential behavior. Inclusion of products in the feed solves this problem, allowing accurate determination of kinetic parameters such as apparent reaction orders and activation energies. We also demonstrate that evaluation of the necessity of co-feeding products to assure measurement of differential-reactor data in a given catalytic system is straightforward from a plot of the log of the rate (or conversion) versus the log of the space time in a flow reactor or elapsed time in a batch reactor. We encourage inclusion of this test in all kinetic analyses that are reasonably approximated by power law rate expressions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗