Engineering Papers⌕ Search

Engineering topics

Hargather, Michael J.

Publications and source records attributed to Hargather, Michael J..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Characterization of the fractal dimension of helium plumes in laminar to turbulent transition

Abstract Schlieren imaging in conjunction with a high-speed camera was used to observe the behavior of metered helium plumes as they transition from laminar to turbulent flow in an air environment. The plumes were visualized at twelve jet Reynolds numbers ranging from 200 to 2980. The fractal dimension of the flows was obtained by applying a box counting algorithm to the recorded schlieren images. The results were analyzed to determine the correlation between the Reynolds number of the flow and the fractal dimension of the observed turbulence. A trend of increasing fractal dimension with increasing Reynolds number was observed for several different types of schlieren cutoffs including horizontal cutoff, vertical cutoff, circular cutoff, focused shadowgraphy and de-focused shadowgraphy. The vertical cutoff and focused shadowgraphy imaging methods showed the most consistent results for the fractal dimension characterization during the laminar to turbulent transition. For transitional plumes, it was observed that fractal dimension increased with distance from the jet outlet.

42 ENGINEERING↗
DOE OSTI2023

Shear and combustion characterization of printable ammonium perchlorate composite propellant formulations

Seven formulations of ammonium perchlorate composite propellant (APCP) are developed and their properties relevant for successful additive manufacture are characterized. Extrusion in a custom-built 3D printing system and spindle viscometry are used to collect viscosity measurements of curing primary and non-curing secondary versions of the formulations. The formulations that behave similarly to a Bingham plastic, with apparent viscosities between 4 and 8 thousand Pa*s at 30 minutes post-mix, are determined to be most suitable for printing applications. Measurements of one material show a yield stress of 1 kPa. Ambient pressure burn rates of 2.0–2.9 mm/s were measured for the compositions tested. All measured burn rates were comparable to the lower end of typical burn rates for APCP. In conclusion, the results of the characterization demonstrate a propellant suitable for use in a 3D printing system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Trace explosives sampling for security applications (TESSA) study: Evaluation of procedures and methodology for contact sampling efficiency

We report the detection of trace amounts of explosive materials is critical to the security at mass transit centers (e.g., airports and railway stations). In a typical screening process, a trap is used to probe a surface of interest to collect and transfer particulate residue to a detector for analysis. The collection of residues from the surface being probed is widely viewed as the limiting step in this process. A multi-institutional study was performed to establish a methodology for the evaluation of sampling media collection efficiencies. Dry deposited residues of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX), C-4 (an RDX-based explosive), and pentaerythritol tetranitrate (PETN) were harvested from acrylonitrile butadiene styrene (ABS) plastic, ballistic nylon (NYL), and uncoated aluminum surfaces using muslin, Texwipe cotton, and stainless-steel mesh traps. Transfer and collection efficiencies of the sample media were calculated based on liquid chromatography-mass spectrometry analysis. Dry transfer efficiencies (DTE%) to all tested surfaces were greater than 75%, with transfer to ABS plastic being the lowest. Collection efficiency (CE%) varied significantly across the traps and the surfaces, yet some conclusions can be drawn; nylon had the lowest CE% for all cases (~10%), and the stainless steel mesh had the lowest CE% for the evaluated traps (~20%). Though the testing parameters have been standardized among the participants to establish a framework for an independent comparison of contact sampling media and surfaces, substantial variations in the DTE% and the CE% were observed, suggesting that other variables can affect contact sampling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗