Engineering topics

Harding, David J.

Publications and source records attributed to Harding, David J..

22 records · Page 2

NASA NTRS1995

Estimation of penetration of forest canopies by Interferometric SAR measurements

In contrast to traditional Synthetic Aperture Radar (SAR), an Interferometric SAR (INSAR) yields two additional measurements: the phase difference and the correlation between the two interferometric channels. The phase difference has been used to estimate topographic height. For homogeneous surfaces, the correlation depends on the system signal-to-noise (SNR) ratio, the interferometer parameters, and the local slope. In the presence of volume scattering, such as that encountered in vegetation canopies, the correlation between the two channels is also dependent on the degree of penetration of the radiation into the scattering medium. In this paper, we propose a method for removing system and slope effects in order to obtain the decorrelation due to penetration alone. The sensitivities and accuracy of the proposed method are determined by Monte Carlo experiments, and we show that the proposed technique has sufficient sensitivity to provide penetration measurements for airborne SAR systems. Next, we provide a theoretical model to estimate the degree of penetration in a way which is independent of the details of the scattering medium. We also present a model for the correlation from non-homogeneous layers. We assess the sensitivity of the proposed inversion technique to these inhomogeneous situations. Finally, we present a comparison of the interferometric results against in situ data obtained by an airborne laser profilometer which provides a direct measurement of tree height and an estimate of the vegetation density profile in the forested areas around Mt. Adams, WA.

Rodriguez, Ernesto↗

NASA NTRS1993

Multi-beam laser altimeter

Laser altimetry provides a high-resolution, high-accuracy method for measurement of the elevation and horizontal variability of Earth-surface topography. The basis of the measurement is the timing of the round-trip propagation of short-duration pulses of laser radiation between a spacecraft and the Earth's surface. Vertical resolution of the altimetry measurement is determined primarily by laser pulsewidth, surface-induced spreading in time of the reflected pulse, and the timing precision of the altimeter electronics. With conventional gain-switched pulses from solid-state lasers and sub-nsec resolution electronics, sub-meter vertical range resolution is possible from orbital attitudes of several hundred kilometers. Horizontal resolution is a function of laser beam footprint size at the surface and the spacing between successive laser pulses. Laser divergence angle and altimeter platform height above the surface determine the laser footprint size at the surface, while laser pulse repetition-rate, laser transmitter beam configuration, and altimeter platform velocity determine the space between successive laser pulses. Multiple laser transitters in a singlaltimeter instrument provide across-track and along-track coverage that can be used to construct a range image of the Earth's surface. Other aspects of the multi-beam laser altimeter are discussed.

Bufton, Jack L.↗

NASA NTRS1991

Surface scattering properties estimated from modeling ASAS multiple emission angle reflectance data over the lunar crater volcanic field, Nevada

ASAS multispectral data were acquired over Lunar Lake playa at 12 different lighting and viewing geometries. Atmospheric models and field-based data demonstrate that atmospheric contributions to ASAS data were relatively small and were thus ignored in analyses of surface photometric properties. ASAS data of an artificially roughened playa and cobble-strewn surfaces exhibit trends of increasing reflectance as phase angle decreases. The reflectance of a natural playa surface exhibits Lambertian scattering properties that cannot be replicated with the Hapke (1986) photometric function. The Hapke model does fit the rough and cobble-strewn playa data with single-scattering albedo, asymmetry factor, and roughness terms consistent with known properties of these surfaces. No published photometric model explains the reflectance variations of all three surfaces.

Guinness, Edward A.↗

NASA NTRS1989

Spectral mapping of Alaskan ophiolites using Landsat Thematic Mapper data

Ophiolites are sections of oceanic lithosphere that have been exposed by thrusting in mountain belts. Thematic Mapper three-band color composites have been used to differentiate the main rock types of the ophiolites of the western Brooks Range, Alaska, and to map mineralogic variations produced by processes that affect oceanic lithosphere, such as mantle partial melting, hydration of ultramafic rock, formation of cumulate layers, and hydrothermal alteration and metamorphism of basalt. Scaled composites of TM Bands 7, 3, 1 and 5, 4, 2, and 3, 2, 1, displayed in red, green, and blue are most useful for visually differentiating rocks of the ophiolites. Ternary diagrams of digital number values are used to evaluate color variations observed in the three-band composites. Geologic maps, interpreted from TM images and reconnaissance field studies, are presented for the Asik Mountain, Maiyumerak Mountains, Avan Hills, and Misheguk Mountain ophiolites. The mapping results are being used to guide additional studies of the tectonics of the Brooks Range ophiolites.

Harding, David J.↗