Engineering Papers⌕ Search

Engineering topics

Hao, Y

Publications and source records attributed to Hao, Y.

At least 55 records · Page 3

Final Report: Improved Site Characterization And Storage Prediction Through Stochastic Inversion Of Time-Lapse Geophysical And Geochemical Data

During the last months of this project, our project activities have concentrated on four areas: (1) performing a stochastic inversion of pattern 16 seismic data to deduce reservoir bulk/shear moduli and density; the need for this inversion was not anticipated in the original scope of work, (2) performing a stochastic inversion of pattern 16 seismic data to deduce reservoir porosity and permeability, (3) complete the software needed to perform geochemical inversions and (4) use the software to perform stochastic inversion of aqueous chemistry data to deduce mineral volume fractions. This report builds on work described in progress reports previously submitted (Ramirez et al., 2009, 2010, 2011 - reports fulfilled the requirements of deliverables D1-D4) and fulfills deliverable D5: Field-based single-pattern simulations work product. The main challenge with our stochastic inversion approach is its large computational expense, even for single reservoir patterns. We dedicated a significant level of effort to improve computational efficiency but inversions involving multiple patterns were still intractable by project's end. As a result, we were unable to fulfill Deliverable D6: Field-based multi-pattern simulations work product.

58 GEOSCIENCES↗

Feedback scheme for kink instability in ERL based electron ion collider

Kink instability presents one of the limiting factors from achieving higher luminosity in ERL based electron ion collider (EIC). However, we can take advantage of the flexibility of the linac and design a feedback system to cure the instability. This scheme raises the threshold of kink instability dramatically and provides opportunity for higher luminosity. We studied the effectiveness of this system and its dependence on the amplitude and phase of the feedback. In this paper we present results of theses studies of this scheme and describe its theoretical and practical limitations. The main advantage of an energy recovery linac (ERL) based electron ion collider (EIC) over a ring-ring type counterpart is the higher achievable luminosity. In ERL-based version, one electron beam collides with the opposing ion beam only once so that the beam-beam parameter can largely exceed the usual limitation in an electron collider ring, while the beam-beam parameter for the ion beam remains small values. The resulting luminosity may be enhanced by one order of magnitude. The beam dynamics related challenges also arise as the luminosity boost in ERL based EIC due to the significant beam-beam effect on the electron beam. The effects on the electron beam include the additional large beam-beam tune shift and nonlinear emittance growth, which are discussed. The ion beam may develop a head-tail type instability, referred as 'kink instability', through the interaction with the electron beam. In this paper, we discuss the feasibility of an active feedback system to mitigate the kink instability, by taking advantage of the flexibility of ERL. Throughout the paper, we will discuss the collision between proton and electron beam. Any other ion species can be scaled by its charge Z and ion mass A.

43 PARTICLE ACCELERATORS↗

Ion trapping study in eRHIC

The ion trapping effect is an important beam dynamics issue in energy recovery linac (ERL). The ionized residue gas molecules can accumulate at the vicinity of the electron beam path and deteriorate the quality of the electron beam. In this paper, we present calculation results to address this issue in eRHIC and find best beam pattern to eliminate this effect. eRHIC is the future electron ion collider(EIC), which collides 5GeV to 30GeV electron beam from a new electron accelerator with the ion beam from existing RHIC ring. The electron accelerator adopts a multi-pass ERL, which contains 6 passes with 2 linacs per pass. The electron impacted ionization effect needs attention to ensure the quality of the electron beam. The high energy electrons ionize the residue gas in beam pipe. These ions may accumulate and are 'trapped' near the axis of the pipe where the electron beam passes, due to the interaction with the electron beam. The concentration of the ion may produce noticeable space charge field that affects the electron beam and neutralize the electron beam in the linacs. In the paper, we start with cross section of the ionization process and calculate the accumulation time, which are followed by the modeling to determine the criteria of the ion trapping. The ion trapping effect is determined by the longitudinal configuration of the electron bunches. The effect can be reduced or mitigate by some proper electron beam patterns. We will present these patterns with a linearized model. We present the linearized calculation on the ion motion in the cavity of multi-pass ERL and determine the stability of the ion motion from the results. We conclude that the ionized molecules won't accumulated in eRHIC linacs except both 40m ends. Electro-static clearing electrodes should be installed in those regions to remove the ions from accumulation.

43 PARTICLE ACCELERATORS↗

Optics-free x-ray FEL oscillator

There is a need for an Optics-Free FEL Oscillators (OFFELO) to further the advantages of free-electron lasers and turning them in fully coherent light sources. While SASE (Self-Amplified Spontaneous Emission) FELs demonstrated the capability of providing very high gain and short pulses of radiation and scalability to the X-ray range, the spectra of SASE FELs remains rather wide ({approx}0.5%-1%) compared with typical short wavelengths FEL-oscillators (0.01%-0.0003% in OK-4 FEL). Absence of good optics in VUV and X-ray ranges makes traditional oscillator schemes with very high average and peak spectral brightness either very complex or, strictly speaking, impossible. In this paper, we discuss lattice of the X-ray optics-free FEL oscillator and present results of initial computer simulations of the feedback process and the evolution of FEL spectrum in X-ray OFFELO. We also discuss main limiting factors and feasibility of X-ray OFFELO.

43 PARTICLE ACCELERATORS↗

High luminosity electron-hadron collider eRHIC

We present the design of a future high-energy high-luminosity electron-hadron collider at RHIC called eRHIC. We plan on adding 20 (potentially 30) GeV energy recovery linacs to accelerate and to collide polarized and unpolarized electrons with hadrons in RHIC. The center-of-mass energy of eRHIC will range from 30 to 200 GeV. The luminosity exceeding 10{sup 34} cm{sup -2} s{sup -1} can be achieved in eRHIC using the low-beta interaction region with a 10 mrad crab crossing. We report on the progress of important eRHIC R&D such as the high-current polarized electron source, the coherent electron cooling, ERL test facility and the compact magnets for recirculation passes. A natural staging scenario of step-by-step increases of the electron beam energy by building-up of eRHIC's SRF linacs is presented.

43 PARTICLE ACCELERATORS↗

Lattice design for the future ERL-based electron hadron colliders eRHIC and LHeC

We present a lattice design of a CW Electron Recovery Linacs (ERL) for future electron hadron colliders eRHIC and LHeC. In eRHIC, an six-pass ERL installed in the existing Relativistic Heavy Ion Collider (RHIC) tunnel will collide 5-30 GeV polarized electrons with RHIC's 50-250 (325) GeV polarized protons or 20-100 (130) GeV/u heavy ions. In LHeC a stand-along, 3-pass 60 GeV CW ERL will collide polarized electrons with 7 TeV protons. After collision, electron beam energy is recovered and electrons are dumped at low energy. Two superconducting linacs are located in the two straight sections in both ERLs. The multiple arcs are made of Flexible Momentum Compaction lattice (FMC) allowing adjustable momentum compaction for electrons with different energies. The multiple arcs, placed above each other, are matched to the two linac's straight sections with splitters and combiners.

43 PARTICLE ACCELERATORS↗

Proof-of-Principle Experiment for FEL-based Coherent Electron Cooling

Coherent electron cooling (CEC) has a potential to significantly boost luminosity of high-energy, high-intensity hadron-hadron and electron-hadron colliders*. In a CEC system, a hadron beam interacts with a cooling electron beam. A perturbation of the electron density caused by ions is amplified and fed back to the ions to reduce the energy spread and the emittance of the ion beam. To demonstrate the feasibility of CEC we propose a proof-of-principle experiment at RHIC using one of JLab’s SRF cryo-modules. In this paper, we describe the experimental setup for CeC installed into one of RHIC's interaction regions. We present results of analytical estimates and results of initial simulations of cooling a gold-ion beam at 40 GeV/u energy via CeC.

43 PARTICLE ACCELERATORS↗

Fully Coupled Geomechanics and Discrete Flow Network Modeling of Hydraulic Fracturing for Geothermal Applications

The primary objective of our current research is to develop a computational test bed for evaluating borehole techniques to enhance fluid flow and heat transfer in enhanced geothermal systems (EGS). Simulating processes resulting in hydraulic fracturing and/or the remobilization of existing fractures, especially the interaction between propagating fractures and existing fractures, represents a critical goal of our project. To this end, we are continuing to develop a hydraulic fracturing simulation capability within the Livermore Distinct Element Code (LDEC), a combined FEM/DEM analysis code with explicit solid-fluid mechanics coupling. LDEC simulations start from an initial fracture distribution which can be stochastically generated or upscaled from the statistics of an actual fracture distribution. During the hydraulic stimulation process, LDEC tracks the propagation of fractures and other modifications to the fracture system. The output is transferred to the Non-isothermal Unsaturated Flow and Transport (NUFT) code to capture heat transfer and flow at the reservoir scale. This approach is intended to offer flexibility in the types of analyses we can perform, including evaluating the effects of different system heterogeneities on the heat extraction rate as well as seismicity associated with geothermal operations. This paper details the basic methodology of our approach. Two numerical examples showing the capability and effectiveness of our simulator are also presented.

15 GEOTHERMAL ENERGY↗

Progress Report, December 2010: Improved Site Characterization And Storage Prediction Through Stochastic Inversion Of Time-Lapse Geophysical And Geochemical Data

Over the last project six months, our project activities have concentrated on three areas: (1) performing a stochastic inversion of pattern 16 seismic data to deduce reservoir permeability, (2) development of the geochemical inversion strategy and implementation of associated software, and (3) completing the software implementation of TProGS and the geostatistical analysis that provides the information needed when using the software to produce realizations of the Midale reservoir. The report partially the following deliverables: D2: Model development: MCMC tool (synthetic fluid chemistry data); deliverable completed. D4: Model development/verification: MCMC tool (TProGS, field seismic/chemistry data) work product; deliverable requirements partially fulfilled. D5: Field-based single-pattern simulations work product; deliverable requirements partially fulfilled. When completed, our completed stochastic inversion tool will explicitly integrate reactive transport modeling, facies-based geostatistical methods, and a novel stochastic inversion technique to optimize agreement between observed and predicted storage performance. Such optimization will be accomplished through stepwise refinement of: (1) the reservoir model - principally its permeability magnitude and heterogeneity - and (2) geochemical parameters - primarily key mineral volume fractions and kinetic data. We anticipate that these refinements will facilitate significantly improved history matching and forward modeling of CO{sub 2} storage. Our tool uses the Markov Chain Monte Carlo (MCMC) methodology. Deliverable D1, previously submitted as a report titled ''Development of a Stochastic Inversion Tool To Optimize Agreement Between The Observed And Predicted Seismic Response To CO{sub 2} Injection/Migration in the Weyburn-Midale Project'' (Ramirez et al., 2009), described the stochastic inversion approach that will identify reservoir models that optimize agreement between the observed and predicted seismic response. The software that implements this approach has been completed, tested, and used to process seismic data from pattern 16. A previously submitted report titled ''Model verification: synthetic single pattern simulations using seismic reflection data'', Ramirez et al. 2010, partially fulfilled deliverable D3 by summarizing verification activities that evaluate the performance of the seismic software and its ability to recover reservoir model permeabilities using synthetic seismic reflection data. A future progress report will similarly describe summarizing verification activities of the geochemical inversion software, thereby completing deliverable D3. This document includes a chapter that shows and discusses permeability models produced by seismic inversion that used seismic data from pattern 16 in Phase 1A. It partially fulfills deliverable D5: Field-based single-pattern simulations work product. The D5 work product is supposed to summarize the results of applying NUFT/MCMC to refine the reservoir model and geochemical parameters by optimizing observation/prediction agreement for the seismic/geochemical response to CO{sub 2} injection/migration within a single pattern of Phase 1A/1B. A future progress report will show inversion results for the same pattern using geochemical data, thereby completing deliverable D5. This document also contains a chapter that fulfills deliverable D2: Model development: MCMC tool (synthetic fluid chemistry data). The chapter will summarize model development activities required to facilitate application of NUFT/MCMC to optimize agreement between the observed and predicted geochemical response to CO{sub 2} injection/migration. Lastly, this document also contains a chapter that partially fulfills deliverable D4: Model development/verification: MCMC tool (TProGS, field seismic/chemistry data) work product. This work product is supposed to summarize model development activities required for (1) application of TProGS to Weyburn, (2) use of TProGS within the MCMC tool, and (3) application of the MCMC tool to address field seismic and geochemical data. The chapter included here fulfills requirements 1 and 2. Requirement 3 will be addressed in a future progress report.

58 GEOSCIENCES↗

Preliminary study for the OFFELO

X-ray Optics-Free FEL Oscillator (OFFELO) has potential of becoming a choice for next generation light sources. Using electron beam for the feedback allows OFFELO to be completely tunable and to combine the peak power of high-gain SASE FELs with extremely narrow bandwidth of the oscillator. While the high-gain X-ray FELs has been studied in depth and has been successfully demonstrated, two other concepts (the transport and the feed-back) involved in OFFELO still need detail studies. In this short paper we focus on the simulation of the feedback process and the evolution of FEL spectrum in X-ray OFFELO. In our initial studies of OFFELO studied the saturation of the system and also its evolution using Genesis 2.0 code with a homemade wrapping code. While and lattice design from the modulator to the radiator, in order to minimize the feedback information loss in transporting the beam.

43 PARTICLE ACCELERATORS↗

FEL potential of eRHIC

Brookhaven National Laboratory plans to build a 5-to-30 GeV energy-recovery linac (ERL) for its future electron-ion collider, eRHIC. In past few months, the Laboratory turned its attention to the potential of this unique machine for free electron lasers (FELS), which we initially assessed earlier. In this paper, we present our current vision of a possible FEL farm, and of narrow-band FEL-oscillators driven by this accelerator. eRHIC, the proposed electron-ion collider at BNL, takes advantage of the existing Relativistic Heavy Ion Collider (RHIC) complex. Plans call for adding a six-pass super-conducting (SRF) ERL to this complex to collide polarized- and unpolarized- electron beams with heavy ions (with energies up to 130 GeV per nucleon) and with polarized protons (with energies up to 325 GeV). RHIC, with a circumference of 3.834 km, has three-fold symmetry and six straight sections each {approx} 250 m long. Two of these straight sections will accommodate 703-MHz SRF linacs. The maximum energy of the electron beam in eRHIC will be reached in stages, from 5 GeV to 30 GeV, by increasing the lengths of its SRF linacs. We plan to install at the start the six-pass magnetic system with small gap magnets. The structure of the eRHIC's electron beam will be identical with that of its hadron beam, viz., 166 bunches will be filled, reserving about a one-microsecond gap for the abort kicker. With modest modifications, we can assure that eRHIC's ERL will become an excellent driver for continuous wave (CW) FELs (see Fig.1). The eRHIC's beam structure will support the operation of several such FELs in parasitic mode.

43 PARTICLE ACCELERATORS↗

Effect of electron disruption in the energy recovery linac based electron ion collider

Beam-beam effects present one of the major factors limiting the luminosity of colliders. In the energy recovery linac (ERL) based eRHIC design, the electron beam, accelerated in a superconducting ERL, collides with the proton beam circulating in the RHIC ring. During such collisions the electron beam undergoes a very strong beam-beam interaction with the protons, which warrants careful examination. We evaluated transverse disruption and linear mismatch effects in the electron beam caused by collisions and considered several countermeasures to mitigate the emittance growth from these interactions. The minimum required aperture of transport lines is calculated that should allow the transport of the electron beam during the deceleration process.

43 PARTICLE ACCELERATORS↗

Studies of Beam Dynamics for eRHIC

We present our studies on various aspects of the beam dynamics in 'racetrack' design of the first stage electron-ion collider at RHIC (eRHIC), including transverse beam break up instabilities, energy loss due to wakefields, electron beam emittance growth and energy loss due to synchrotron radiation, electron beam losses due to Touschek effects and residue gas scattering, beam-beam effects at the interaction region and emittance growth of ion beam due to electron bunch to bunch noises. For all effects considered above, no showstopper has been found.

43 PARTICLE ACCELERATORS↗

RHIC PERFORMANCE DURING THE FY10 200 GeV Au+Au HEAVY ION RUN

Since the last successful RHIC Au+Au run in 2007 (Run-7), the RHIC experiments have made numerous detector improvements and upgrades. In order to benefit from the enhanced detector capabilities and to increase the yield of rare events in the acquired heavy ion data a significant increase in luminosity is essential. In Run-7 RHIC achieved an average store luminosity of <L> = 12 x 10{sup 26} cm{sup -2} s{sup -1} by operating with 103 bunches (out of 111 possible), and by squeezing to {beta}* = 0.85 m. This year, Run-10, we achieved <L> = 20 x 10{sup 26} cm{sup -2} s{sup -1}, which put us an order of magnitude above the RHIC design luminosity. To reach these luminosity levels we decreased {beta}* to 0.75 m, operated with 111 bunches per ring, and reduced longitudinal and transverse emittances by means of bunched-beam stochastic cooling. In addition we introduced a lattice to suppress intra-beam scattering (IBS) in both RHIC rings, upgraded the RF control system, and separated transition crossing times in the two rings. We present an overview of the changes and the results of Run-10 performance.

43 PARTICLE ACCELERATORS↗

Lattice design for the ERL electron ion collider in RHIC

We present electron ion collider lattice design for the Relativistic Heavy Ion Collider (eRHIC) where the electrons have multi-passes through recirculating linacs (ERL) and arcs placed in the existing RHIC tunnel. The present RHIC interaction regions (IR's), where the electron ion collisions will occur, are modified to allow for the large luminosity. Staging of eRHIC will bring the electron energy from 4 up to 20 (30) GeV as the superconducting cavities are built and installed sequentially. The synchrotron radiation from electrons at the IR is reduced as they arrive straight to the collision while ions and protons come with 10 mrad crossing angle using the crab cavities.

43 PARTICLE ACCELERATORS↗

Study of beam-beam effects in eRHIC

Beam-beam effects in eRHIC have a number of unique features, which distinguish them from both hadron and lepton colliders. Due to beam-beam interaction, both electron and hadron beams would suffer quality degradation or beam loss from without proper treatments. Those features need novel study and dedicate countermeasures. We study the beam dynamics and resulting luminosity of the characteristics, including mismatch, disruption and pinch effects on electron beam, in additional to their consequences on the opposing beam as a wake field and other incoherent effects of hadron beam. We also carry out countermeasures to prevent beam quality degrade and coherent instability.

43 PARTICLE ACCELERATORS↗

The Transverse Linac Optics Design in Multi-pass ERL

In this paper, we analyzed the linac optics design requirement for a multi-pass energy recovery linac (ERL) for arbitrary number of linacs. A set of general formula of constrains for the 2-D transverse matrix is derived to ensure design optics acceptance matching throughout the entire accelerating and decelerating process. Meanwhile, the rest free parameters can be adjusted for fulfilling other requirements or optimization purpose. As an example, we design the linac optics for the future MeRHIC (Medium Energy eRHIC) project and show the optimization for small {beta} function.

43 PARTICLE ACCELERATORS↗

Small gap magnet prototype measurements for eRHIC

In this paper we present the design and prototype measurement of small gap (5mm to 10 mm aperture) dipole and quadrupole for the future high energy ERL (Energy Recovery Linac). The small gap magnets have the potential of largely reducing the cost of the future electron-ion collider project, eRHIC, which requires a 10GeV to 30 GeV ERL with up to 6 energy recovery passes (3.8 km each pass). We also studied the sensitivity of the energy recovery pass and the alignment error in this small magnets structure and countermeasure methods.

43 PARTICLE ACCELERATORS↗