Engineering Papers⌕ Search

Engineering topics

Haney, H. P.

Publications and source records attributed to Haney, H. P..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Computational aerodynamic design methodology

The transonic wing design process has been vastly improved at Lockheed-Georgia. The revised design procedure enhances useability and reliability by combining numerical optimization and inverse design into a single wing design code with transonic analysis provided by a modified version of FLO22. A more versatile set of geometric decision variables has been integrated into the optimization portion for geometry perturbations. An automatic restart feature permits the interchangeability of solutions between optimization and inverse design as the design progresses. In combination, these improvements enable practical utilization of a VAX 11/780 computer and significantly reduce the elapsed time required to complete a transonic wing design.

Burris, C. B.↗
NASA NTRS1981

A comparison of theoretical and experimental pressure distributions for two advanced fighter wings

A comparison was made between experimental pressure distributions measured during testing of the Vought A-7 fighter and the theoretical predictions of four transonic potential flow codes. Isolated wind and three wing-body codes were used for comparison. All comparisons are for transonic Mach numbers and include both attached and separate flows. In general, the wing-body codes gave better agreement with the experiment than did the isolated wing code but, because of the greater complexity of the geometry, were found to be considerably more expensive and less reliable.

Haney, H. P.↗
NASA NTRS1980

Application of numerical optimization to the design of wings with specified pressure distributions

A practical procedure for the optimum design of transonic wings is demonstrated. The procedure uses an optimization program based on the method of feasible directions coupled with an aerodynamic analysis program which solves the three-dimensional potential equation for subsonic through transonic flow. Two new wings for the A-7 aircraft were designed by using the optimization procedure to achieve specified surface pressure distributions. The new wings, along with the existing A-7 wing, were tested in the Ames 11 ft transonic wind tunnel. The experimental data show that all of the performance goals were met. However, comparisons of the wind tunnel results with the theoretical predictions indicate some differences at conditions for which strong shock waves occur.

Haney, H. P.↗
NASA NTRS1979

Computational optimization and wind tunnel test of transonic wing designs

A practical procedure for the optimum design of transonic wings is demonstrated. The procedure uses an optimization program based on the method of feasible directions coupled with an aerodynamic analysis program which solves the three-dimensional potential equation for subsonic through transonic flow. Two new wings for the A-7 aircraft were designed by using the optimization procedure to achieve specified surface pressure distributions. The new wings, along with the existing A-7 wing, were tested in the Ames 11-foot transonic wind tunnel. The experimental data show that all of the performance goals were met.

Haney, H. P.↗
NASA NTRS1978

Computational wing optimization and comparisons with experiment for a semi-span wing model

A computational wing optimization procedure was developed and verified by an experimental investigation of a semi-span variable camber wing model in the NASA Ames Research Center 14 foot transonic wind tunnel. The Bailey-Ballhaus transonic potential flow analysis and Woodward-Carmichael linear theory codes were linked to Vanderplaats constrained minimization routine to optimize model configurations at several subsonic and transonic design points. The 35 deg swept wing is characterized by multi-segmented leading and trailing edge flaps whose hinge lines are swept relative to the leading and trailing edges of the wing. By varying deflection angles of the flap segments, camber and twist distribution can be optimized for different design conditions. Results indicate that numerical optimization can be both an effective and efficient design tool. The optimized configurations had as good or better lift to drag ratios at the design points as the best designs previously tested during an extensive parametric study.

Waggoner, E. G.↗
NASA NTRS1978

Computational wing optimization and wind tunnel test of semi-span model

A computational transonic wing design procedure has been developed and verified by a wind tunnel test of a variable camber semi-span wing model. The Bailey-Ballhaus transonic potential flow analysis code linked to Vanderplaat's constrained minimization routine was used to optimize test configurations at 0.9 Mach number. Based on wind tunnel test results, computationally optimized designs were as efficient as the best configurations determined by previous parametric testing and performed better at off-design points. Wind tunnel wing pressures agreed well with predictions from the improved Bailey-Ballhaus code at moderate CL's. Computational optimization was shown to be an effective transonic wing design tool.

Haney, H. P.↗