Engineering topics

Hancock, D. J.

Publications and source records attributed to Hancock, D. J..

6 records

NASA NTRS1987

An 8-cm ion thruster characterization

The performance of the Ion Auxiliary Propulsion System (IAPS) thruster was increased to thrust T = 32 mN, specific impulse I sub sp = 4062 s, and thrust-to-power ratio T/P = 33 mN/kW. This performance was obtained by increasing the discharge power, accelerating voltage, propellant flow rate, and chamber magnetic field. Adding a plenum and main vaporizer for propellant distribution was the only major change required in the thruster. The modified thruster characterization is presented. A cathode magnet assembly did not improve performance. A simplified power processing unit was designed and evaluated. This unit decreased the parts count of the IAPS power processing unit by a factor of ten.

Wessel, F. J.↗

NASA NTRS1983

Simplified power processing for ion-thruster subsystems

A review of the thruster/power-processor-interface requirements for (mercury and inert gas) ion-thrusters, an evaluation of various approaches to simplifying the power-processor circuitry, and the test results of the recently developed 8-cm mercury-ion-thruster simplified power-processor unit (SPPU) are presented. The SPPU demonstrates the feasibility of stable thruster operation using highly simplified power-processing techniques and achieves an approximately tenfold reduction in the electronic parts count when compared to the existing power-processor unit (PPU) used in the Hughes/NASA Lewis Research Center 8-cm-diameter (mercury) Ion Auxiliary Propulsion Subsystem (IAPS).

Wessel, F. J.↗

NASA NTRS1983

Simplified power processing for ion-thruster subsystems

A design for a greatly simplified power-processing unit (SPPU) for the 8-cm diameter mercury-ion-thruster subsystem is discussed. This SPPU design will provide a tenfold reduction in parts count, a decrease in system mass and cost, and an increase in system reliability compared to the existing power-processing unit (PPU) used in the Hughes/NASA Lewis Research Center Ion Auxiliary Propulsion Subsystem. The simplifications achieved in this design will greatly increase the attractiveness of ion propulsion in near-term and future spacecraft propulsion applications. A description of a typical ion-thruster subsystem is given. An overview of the thruster/power-processor interface requirements is given. Simplified thruster power processing is discussed.

Wessel, F. J.↗

NASA NTRS1983

Simplified power processing for ion-thruster subsystems

Compared to chemical propulsion, ion propulsion offers distinct payload-mass increases for many future low-thrust earth-orbital and deep-space missions. Despite this advantage, the high initial cost and complexity of ion-propulsion subsystems reduce their attractiveness for most present and near-term spacecraft missions. Investigations have, therefore, been conducted with the objective to attempt to simplify the power-processing unit (PPU), which is the single most complex and expensive component in the thruster subsystem. The present investigation is concerned with a program to simplify the design of the PPU employed in a 8-cm mercury-ion-thruster subsystem. In this program a dramatic simplification in the design of the PPU could be achieved, while retaining essential thruster control and subsystem operational flexibility.

Wessel, F. J.↗

NASA NTRS1982

A 10-kW series resonant converter design, transistor characterization, and base-drive optimization

The development, components, and performance of a transistor-based 10 kW series resonant converter for use in resonant circuits in space applications is described. The transistors serve to switch on the converter current, which has a half-sinusoid waveform when the transistor is in saturation. The goal of the program was to handle an input-output voltage range of 230-270 Vdc, an output voltage range of 200-500 Vdc, and a current limit range of 0-20 A. Testing procedures for the D60T and D7ST transistors are outlined and base drive waveforms are presented. The total device dissipation was minimized and found to be independent of the regenerative feedback ratio at lower current levels. Dissipation was set at within 10% and rise times were found to be acceptable. The finished unit displayed a 91% efficiency at full power levels of 500 V and 20 A and 93.7% at 500 V and 10 A.

Robson, R. R.↗

NASA NTRS1967

System precisely controls oscillation of vibrating mass

System precisely controls the sinusoidal amplitude of a vibrating mechanical mass. Using two sets of coils, the system regulates the drive signal amplitude at the precise level to maintain the mechanical mass when it reaches the desired vibration amplitude.

Hancock, D. J.↗