Engineering topics

Hamad, Khaleel

Publications and source records attributed to Hamad, Khaleel.

4 records

DOE OSTI2022

Nanostructured Powders Made from Flame Spray Pyrolysis for Li-Ion Cathode

Flame processes are the most economic ones to produce fine powders and have been used to produce pigment titanium oxide and fused silica in large volumes. In this work a flame spray pyrolysis (FSP) process is used to make positive electrode materials for Li-ion battery, which is made of complex metal oxide powders, such as Li(Ni1/3Mn1/3Co1/3)O2. In particular, the work was focused on making the NMC materials with stoichiometric compositions and desired morphologies. During the pyrolysis process different morphologies can be formed, involving often powders with primary nanoparticles. Such nanostructures were found to have affected the battery performance. Detailed results of the synthesis, characterization, and battery testing of the NMC powder materials will be presented.

25 ENERGY STORAGE↗

DOE OSTI2022

Transition Metal Oxide Powders Made from Flame Spray Pyrolysis for Li-Ion Batteries

In 2012 the U.S. Department of Energy introduced its EV Everywhere Grand Challenge, with a stated goal of enabling “plug-in electric vehicles (PEVs) that are as affordable and convenient for the American family as gasoline-powered vehicles by 2022.” This requires a reduction in battery costs from the current $500/kWh to around $125/kWh. Most approaches have been to eliminate vehicle weight through lightweighting and to improve the energy density of battery materials. But what if we were able to just make the materials cheaper instead? To this end we introduce a green, low-cost method of producing cathode materials using an integrated flame spray pyrolysis process.

25 ENERGY STORAGE↗

DOE OSTI2022

Lithium Ion Cathode Materials Prepared Using Glycerol as Solvent and Reactant

Two different types of cathode materials were prepared using glycerol as a solvent and reactant. The LiMn1/3Ni1/3Co1/3O2 layered oxide cathode material was successfully synthesized with a shorter time of heat treatment of 8hr at 900°C. An appreciated capacity retention of 83.7% after 100 cycles with an initial discharge capacity of 177.1 mAh/g at 0.1C (discharge rate) has been achieved. Another cathode material with the formula of Li1.2 Mn0.51Ni0.145+xCo0.145-xO2 (x=0 (LR2), 0.0725 (LR1)), as a Li-rich cathode material, has been also successfully synthesized using glycerol. It was shown that LR1 discharge capacity was increased from 185 to 213 mAh/g after 20 cycles and ended up with 194.9 mAh/g after 60 cycles at 0.1C (discharge rate). This material shows an exceptional discharge capacity retention, lower toxic cobalt component, and lower production cost comparing with other Li-rich cathode materials. Detailed results of powder material synthesis, characterization, and battery testing will be presented to demonstrate that glycerol as a green solvent in the synthesis of battery materials.

25 ENERGY STORAGE↗

DOE OSTI2020

A scalable approach of using biomass derived glycerol to synthesize cathode materials for lithium-ion batteries

Glycerol, a main byproduct of biodiesel, was used as the fuel agent in a scalable flame-assisted spray pyrolysis approach to synthesize micron-size cathode materials. Single droplet combustion, particle morphology, and electrochemical performance were examined considering the effects of salt concentration, water addition, and post-annealing time on synthesizing Li(Ni 1/3 Co 1/3 Mn 1/3 )O 2 (NCM111) cathode materials. Single droplet tests showed that a sufficient amount of water in the glycerol-based precursor could delay droplet inflation and ignition. Moreover, using a two-fluid atomization nozzle, spray tests demonstrated that adding water would result in less wrinkled and more uniform particles. Nevertheless, increasing water proportion in the precursor could reduce the reaction heat, resulting in that samples prepared with water addition needed longer post-annealing time to improve their electrochemical performance. Using the precursor without water, the best performed NCM111 cathode material was synthesized with only 2 h of post-annealing. It has a discharge capacity of 163.3 mAh/g at 0.1C and 85.5% capacity retention at 1C after 100 cycles. Furthermore, the current work confirmed the capability of using glycerol as a sustainable fuel agent to synthesize NCM111 cathode materials, and also provided basic conditions for the development of large-scale production in the future.

25 ENERGY STORAGE↗