Engineering Papers⌕ Search

Engineering topics

Hair, L. M.

Publications and source records attributed to Hair, L. M..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Low L/D aerobrake test at Mach 10

An aerobraking Orbital transfer vehicle may be used to increase the Space Shuttle mission capability to and from high orbits. A Mach 10 wind-tunnel test was performed for a low lift-drag aerobrake, to define a preliminary aerothermal environment for this candidate concept. Test hardware simulated the ribs and stretched fabric of conceptual flight hardware. Pressures, paint-melting histories, and oilflow data were measured on the brake. Pressure and thermocouple heating rate data were measured on the payload. Brake peak heating is at the edge at all angles of attack, although the stagnation point is not outboard of 75 percent radius even at 20 degrees angle of attack. Brake ribs show slightly higher heating than flats, although pressures are essentially constant. Payload peak heating occurs near 12 degrees angle of attack, and is 30 percent of the sphere stagnation point heating (for a sphere of brake diameter). Payload pressure distributions follow the heating pattern. Reynolds number effects are small on the brake and large on the payload, for the range of test conditions: 0.4-1.0 million/foot.

Hair, L. M.↗
NASA NTRS1980

Wake flowfields for Jovian probe

The wake flow field developed by the Galileo probe as it enters the Jovian atmosphere was modeled. The wake produced by the probe is highly energetic, yielding both convective and radiative heat inputs to the base of the probe. A component mathematical model for the inviscid near and far wake, the viscous near and far wake, and near wake recirculation zone was developed. Equilibrium thermodynamics were used for both the ablation and atmospheric species. Flow fields for three entry conditions were calculated. The near viscous wave was found to exhibit a variable axial pressure distribution with the neck pressure approximately three times the base pressure. Peak wake flow field temperatures were found to be in proportion to forebody post shock temperatures.

Engel, C. D.↗
NASA NTRS1978

Space shuttle afterbody aerodynamics/plume simulation data summary

A series of parametric wind tunnel tests was conducted to provide a base for developing a simulation of afterbody/base aerodynamics for multibody/multibase rocket-powered vehicles (such as Space Shuttle) which use unheated air as the simulant gas in development wind tunnel tests. The tests described were parameterized on external configuration, nozzle internal configuration, base geometry, propulsion gas type, and freestream Mach number (0.5 to 3.5). The tests were conducted over a 4-year period. Presented in this report are the data and pertinent reference information necessary to perform an analysis which would lead to a simulation procedure. The type of data obtained during the tests described herein include model base afterbody, and nozzle internal surface static pressure distributions, model chamber pressure and temperature, and freestream conditions. Also included is a brief description of simulation procedures that were used by the Space Shuttle program.

Blackwell, K. L.↗
NASA NTRS1978

Space Shuttle Plume Simulation Effect on Aerodynamics

Technology for simulating plumes in wind tunnel tests was not adequate to provide the required confidence in test data where plume induced aerodynamic effects might be significant. A broad research program was undertaken to correct the deficiency. Four tasks within the program are reported. Three of these tasks involve conducting experiments, related to three different aspects of the plume simulation problem: (1) base pressures; (2) lateral jet pressures; and (3) plume parameters. The fourth task involves collecting all of the base pressure test data generated during the program. Base pressures were measured on a classic cone ogive cylinder body as affected by the coaxial, high temperature exhaust plumes of a variety of solid propellant rockets. Valid data were obtained at supersonic freestream conditions but not at transonic. Pressure data related to lateral (separation) jets at M infinity = 4.5, for multiple clustered nozzles canted to the freestream and operating at high dynamic pressure ratios. All program goals were met although the model hardware was found to be large relative to the wind tunnel size so that operation was limited for some nozzle configurations.

Hair, L. M.↗
NASA NTRS1978

Pretest information for a test to validate plume simulation procedures (FA-17)

The results of an effort to plan a final verification wind tunnel test to validate the recommended correlation parameters and application techniques were presented. The test planning effort was complete except for test site finalization and the associated coordination. Two suitable test sites were identified. Desired test conditions were shown. Subsequent sections of this report present the selected model and test site, instrumentation of this model, planned test operations, and some concluding remarks.

Hair, L. M.↗
NASA NTRS1976

Test data from small solid propellant rocket motor plume measurements (FA-21)

A program is described for obtaining a reliable, parametric set of measurements in the exhaust plumes of solid propellant rocket motors. Plume measurements included pressures, temperatures, forces, heat transfer rates, particle sampling, and high-speed movies. Approximately 210,000 digital data points and 15,000 movie frames were acquired. Measurements were made at points in the plumes via rake-mounted probes, and on the surface of a large plate impinged by the exhaust plume. Parametric variations were made in pressure altitude, propellant aluminum loading, impinged plate incidence angle and distance from nozzle exit to plate or rake. Reliability was incorporated by continual use of repeat runs. The test setup of the various hardware items is described along with an account of test procedures. Test results and data accuracy are discussed. Format of the data presentation is detailed. Complete data are included in the appendix.

Hair, L. M.↗
NASA NTRS1975

Test data from solid propellant plume aerodynamics test program in Ames 6 x 6 foot supersonic wind tunnel (shuttle test FA7) (Ames test 033-66)

The aerodynamic effects of plumes from hot combustion gases in the presence of a transonic external flow field were measured to advance plumes simulation technology, extend a previously acquired data base, and provide data to compare with the effects observed using cold gas plumes. A variety of underexpanded plumes issuing from the base of a strut-mounted ogive-cylinder body were produced by combusting solid propellant gas generators. The gas generator fired in a short-duration mode (200 to 300 msec). Propellants containing 16 percent and 2 percent A1 were used, with chamber pressures from 400 to 1800 psia. Conical nozzles of 15 deg half-angle were tested with area ratios of 4 and 8. Pressures were measured in the gas generator combustion chamber, along the nozzle wall, on the base, and along the body rear exterior. Schlieren photographs were taken for all tests. Test data are presented along with a description of the test setup and procedures.

Hair, L. M.↗