Engineering topics

Hagaman, J. A.

Publications and source records attributed to Hagaman, J. A..

5 records

NASA NTRS1985

A survey of structural material issues for a space station

An NASA enters the definition phase of the space station project, one of the important issues to be considered is structural material selection. The complexity of the space station and its long life requirement are two key factors which must be considered in the material selection process. Both aluminum and graphite/epoxy are considered as potential structural materials. Advantages and disadvantages of these materials with respect to mechanical and thermal considerations, space environment, manufacturing, and cost are discussed.

Hagaman, J. A.↗

NASA NTRS1983

Buckling and failure characteristics of graphite-polyimide shear panels

The buckling and failure characteristics of unstiffened, blade stiffened, and hat stiffened graphite-polyimide shear panels are described. The picture frame shear test is used to obtain shear stress-strain data at room temperature and at 316 deg C. The experimental results are compared with a linear buckling analysis, and the specimen failure modes are described. The effect of the 316 deg C test temperature on panel behavior are discussed.

Shuart, M. J.↗

NASA NTRS1979

The structural behavior of a graphite-polymide honeycomb sandwich panel with quasi-isotropic face sheets and an orthotropic core

The results of a series of tests of graphite-polyimide honeycomb sandwich panels are presented. The panels were 1.22 m long, 0.508 m wide, and approximately 13.3 m thick. The face sheets were a T-300/PMR-15 fabric in a quasi-isotropic layup and were 0.279 mm thick. The core was Hexcel HRH 327-3/16 - 4.0 glass reinforced polyimide honeycomb, 12.7 mm thick. Three panels were used in the test: one was cut into smaller pieces for testing as beam, compression, and shear specimens; a second panel was used for plate bending tests; the third panel was used for in-plane stability tests. Presented are the experimental results of four point bending tests, short block compression tests, core transverse shear modulus, three point bending tests, vibration tests, plate bending tests, and panel stability tests. The results of the first three tests are used to predict the results of some of the other tests. The predictions and experimental results are compared, and the agreement is quite good.

Hyer, M. W.↗

NASA NTRS1979

The effects of thermal cycling on the thermal deformation of graphite-polyimide

The effects of repetitive thermal cycling on the thermal deformation of graphite-fiber-reinforced polyimide laminates are investigated. Unsymmetric and unidirectional laminate specimens were cycled in an oven between room temperature and 180 or 315 C five times, and temperature and deformation were recorded as a function of time in order to measure thermal deformation. The results of the lower temperature cycling reveal a hysteresis-like effect in the temperature-thermal deformation relation for a single cycle, while no differences are detected from one cycle to the next. The response of an eight-layer curved specimen is found to agree well with predictions based on a piecewise-linear lamination theory, however, four-layer laminate response could not be explained. The results of the high-temperature tests also indicate a dependence of the strain on whether the specimen was being heated or cooled, however quantitative results are considered unreliable, due to strain gage difficulties.

Hyer, M. W.↗

NASA NTRS1979

Thermal cycling graphite-polyimide

The effects of repetitive thermal cycling on the temperature-thermal deformation relation of graphite-polyimide were determined. The bending and axial strains, measured with strain gages, of unsymmetric 0 deg sub 2/90 deg sub 2 and 0 deg sub 4/90 deg sub 4 laminates were used as an indication of thermal deformation. The strains were measured as a function of temperature and two temperature ranges were used, room temperature to 180 C and room temperature to 315 C. Five cycles were run in each temperature range and the cycling was done in quasistatic fashion. The response of a flat 0 deg sub 8 laminate was measured as were the effects of repetitive cycling on the strain gages themselves. A piece-wise linear theory, based on classical lamination theory and using the variation of mechanical and thermal expansion properties with temperature, was compared with the experimental results. The correlation between theoretical predictions and experimental results for the thinner laminate was poor.

Hyer, M. W.↗