Engineering Papers⌕ Search

Engineering topics

Haftka, Raphael T.

Publications and source records attributed to Haftka, Raphael T..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Active vibration control with model correction on a flexible laboratory grid structure

This paper presents experimental and computational comparisons of three active damping control laws applied to a complex laboratory structure. Two reduced structural models were used with one model being corrected on the basis of measured mode shapes and frequencies. Three control laws were investigated, a time-invariant linear quadratic regulator with state estimation and two direct rate feedback control laws. Experimental results for all designs were obtained with digital implementation. It was found that model correction improved the agreement between analytical and experimental results. The best agreement was obtained with the simplest direct rate feedback control.

Schamel, George C., II↗
NASA NTRS1991

Combining global and local approximations

A method based on a linear approximation to a scaling factor, designated the 'global-local approximation' (GLA) method, is presented and shown capable of extending the range of usefulness of derivative-based approximations to a more refined model. The GLA approach refines the conventional scaling factor by means of a linearly varying, rather than constant, scaling factor. The capabilities of the method are demonstrated for a simple beam example with a crude and more refined FEM model.

Haftka, Raphael T.↗
NASA NTRS1991

Modal truncation, Ritz vectors, and derivatives of closed-loop damping ratios

The effect of modal truncation on the damping ratio and their derivatives with respect to an added mass is investigated for a simply supported, multispan beam with a linear quadratic Gaussian control system. It is found that both the damping ratios and derivatives converge slowly, but the derivatives converge more slowly than the damping ratios. However, it is shown that when Ritz vectors corresponding to static displacements due to actuator forces are added to the reduced model, the convergence of both the damping ratios and their derivatives is accelerated. It is also shown that the accuracy of the damping ratio predicted by a reduced-model control design can be improved significantly if the Ritz vectors are included in the design of the control system. Thus, it appears that Ritz vectors added to the reduced model of flexible structures can improve greatly the accuracy of both the design and analysis of the control system.

Sandridge, Chris A.↗
NASA NTRS1991

A discourse on sensitivity analysis for discretely-modeled structures

A descriptive review is presented of the most recent methods for performing sensitivity analysis of the structural behavior of discretely-modeled systems. The methods are generally but not exclusively aimed at finite element modeled structures. Topics included are: selections of finite difference step sizes; special consideration for finite difference sensitivity of iteratively-solved response problems; first and second derivatives of static structural response; sensitivity of stresses; nonlinear static response sensitivity; eigenvalue and eigenvector sensitivities for both distinct and repeated eigenvalues; and sensitivity of transient response for both linear and nonlinear structural response.

Adelman, Howard M.↗
NASA NTRS1991

Recent advances in approximation concepts for optimum structural design

The basic approximation concepts used in structural optimization are reviewed. Some of the most recent developments in that area since the introduction of the concept in the mid-seventies are discussed. The paper distinguishes between local, medium-range, and global approximations; it covers functions approximations and problem approximations. It shows that, although the lack of comparative data established on reference test cases prevents an accurate assessment, there have been significant improvements. The largest number of developments have been in the areas of local function approximations and use of intermediate variable and response quantities. It also appears that some new methodologies are emerging which could greatly benefit from the introduction of new computer architecture.

Barthelemy, Jean-Francois M.↗
NASA NTRS1991

Control effort associated with model reference adaptive control for vibration damping

The performance of Model Reference Adaptive Control (MRAC) is studied in numerical simulations with the objective of understanding the effects of differences between the plant and the reference model. MRAC is applied to two structural systems with adjustable error between the reference model and the actual plant. Performance indices relating to control effort and response characteristics are monitored in order to determine what effects small errors have on the control effort and performance of the two systems. It is shown that reasonable amounts of error in the reference model can cause dramatic increases in both the control effort and response magnitude (as measured by energy integrals) of the plant.

Messer, Richard Scott↗
NASA NTRS1991

Sensitivity-based scaling for correlating structural response from different analytical models

A sensitivity-based linearly varying scale factor is described used to reconcile results from refined models for analysis of the same structure. The improved accuracy of the linear scale factor compared to a constant scale factor as well as the commonly used tangent approximation is demonstrated. A wing box structure is used as an example, with displacements, stresses, and frequencies correlated. The linear scale factor could permit the use of a simplified model in an optimization procedure during preliminary design to approximate the response given by a refined model over a considerable range of design changes.

Chang, Kwan J.↗
NASA NTRS1991

Stacking-sequence optimization for buckling of laminated plates by integer programming

Integer-programming formulations for the design of symmetric and balanced laminated plates under biaxial compression are presented. Both maximization of buckling load for a given total thickness and the minimization of total thickness subject to a buckling constraint are formulated. The design variables that define the stacking sequence of the laminate are zero-one integers. It is shown that the formulation results in a linear optimization problem that can be solved on readily available software. This is in contrast to the continuous case, where the design variables are the thicknesses of layers with specified ply orientations, and the optimization problem is nonlinear. Constraints on the stacking sequence such as a limit on the number of contiguous plies of the same orientation and limits on in-plane stiffnesses are easily accommodated. Examples are presented for graphite-epoxy plates under uniaxial and biaxial compression using a commercial software package based on the branch-and-bound algorithm.

Haftka, Raphael T.↗
NASA NTRS1991

Sensitivity-based scaling for correlating structural response from different analytical models

This paper presents a sensitivity-based linearly varying scale factor used to reconcile results from simple and refined models for analysis of the same structure. The improved accuracy of the linear scale factor compared to a constant scale factor as well as the commonly used tangent approximation is demonstrated. A wing box structure is used as an example, with displacements, stresses and frequencies correlated. The linear scale factor could permit the use of a simplified model in an optimization procedure during preliminary design to approximate the response given by a refined model over a considerable range of design changes.

Chang, Kwan J.↗
NASA NTRS1991

Stacking-sequence optimization for buckling of laminated plates by integer programming

Integer-programming formulations for the design of symmetric and balanced laminated plates under biaxial compression are presented. Both maximization of buckling load for given total thickness, and the minimization of total thickness subject to a buckling constraint are formulated. The design variables that define the stacking sequence of the laminate are zero-one integers. It is shown that the formulation results in a linear optimization problem that can be solved on readily aviable software. Constraints on the stacking sequence such as a limit on the number of contiguous plies of the same orientation and limits on in-plane stiffnesses are easily accommodated. Examples are presented for graphite-epoxy plates under uniaxial and biaxial compression using a commercial software package based on the branch-and-bound algorithm.

Haftka, Raphael T.↗
NASA NTRS1991

New displacement-based methods for optimal truss topology design

Two alternate methods for maximum stiffness truss topology design are presented. The ground structure approach is used, and the problem is formulated in terms of displacements and bar areas. This large, nonconvex optimization problem can be solved by a simultaneous analysis and design approach. Alternatively, an equivalent, unconstrained, and convex problem in the displacements only can be formulated, and this problem can be solved by a nonsmooth, steepest descent algorithm. In both methods, the explicit solving of the equilibrium equations and the assembly of the global stiffness matrix are circumvented. A large number of examples have been studied, showing the attractive features of topology design as well as exposing interesting features of optimal topologies.

Bendsoe, Martin P.↗
NASA NTRS1990

Reducing distortion and internal forces in truss structures by member exchanges

Manufacturing errors in the length of members or joint diameters of large truss reflector backup structures may result in unacceptable large distortion errors or member forces. However, it may be possible to accurately measure these length or diameter errors. The present work suggests that a member and joint placement strategy may be used to reduce distortion errors and internal member forces. A member and joint exchange algorithm is used to demonstrate the potential of this approach on several 102-member and 660-member truss reflector structures. It is shown that it is possible to simultaneously reduce the rms of the surface error and the rms of member forces by two orders of magnitude by member and joint exchanges.

Greene, William H.↗
NASA NTRS1990

Accuracy analysis of the semi-analytical method for shape sensitivity calculation

The semianalytical method of design sensitivity analysis that is widely used for calculating derivatives of static response with respect to design variables for structures modeled by finite elements is studied. It is shown that the method can have serious accuracy problems for shape design variables in structures modeled by beam, plate, truss, frame, and solid elements. Errors are shown to be associated with an incompatibility of the sensitivity field with the structure. An error index is developed to test the accuracy of the semianalytical method. It characterizes the difference in errors between a general finite-difference method and the semianalytical method. A method for improving the accuracy of the semianalytical method (when possible) is provided. Examples are presented to demonstrate the use of the error index.

Barthelemy, Bruno↗
NASA NTRS1990

Initial postbuckling response of an unsymmetrically laminated rectangular plate

It was shown that anisotropic plates can have unstable postbuckling behavior resulting in potential imperfection sensitivity. The degree of instability for rectangular, simply-supported, cross-ply laminated plates is quantified. The analysis is based on asymptotic Koiter-type expansion of postbuckling response. The degree of postbuckling instability is quantified in terms of the reduction in load carrying capacity in the immediate postbuckling range. For graphite-epoxy plates it is found that this measure of instability is very small. Only a low aspect ratio plate with a high degree of anisotropy can have any significant reduction in its buckling load.

Haftka, Raphael T.↗
NASA NTRS1990

Statistical analysis of static shape control in space structures

The article addresses the problem of efficient analysis of the statistics of initial and corrected shape distortions in space structures. Two approaches for improving efficiency are considered. One is an adjoint technique for calculating distortion shapes: the second is a modal expansion of distortion shapes in terms of pseudo-vibration modes. The two techniques are applied to the problem of optimizing actuator locations on a 55 m radiometer antenna. The adjoint analysis technique is used with a discrete-variable optimization method. The modal approximation technique is coupled with a standard conjugate-gradient continuous optimization method. The agreement between the two sets of results is good, validating both the approximate analysis and optimality of the results.

Burdisso, Ricardo A.↗
NASA NTRS1990

Stiffness-matrix condition number and shape sensitivity errors

This paper derives an error magnification index for assessing the sensitivity of the displacement field to errors in the load vector. It is shown that the error magnification index is less conservative than the stiffness-matrix condition number and that, for some cases, no error magnification occurs even when the condition number is very high. The proposed index was used to calculate the derivatives of beam response to changes in the beam structural parameters, using a semianalytical method. It is shown that the proposed index discriminates well between the calculation of the derivative with respect to length, which is very sensitive to errors, and the calculation of the derivative with respect to cross-sectional height, which is not sensitive.

Haftka, Raphael T.↗