Engineering Papers⌕ Search

Engineering topics

H. Douglas Perkins

Publications and source records attributed to H. Douglas Perkins.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

RDE Nozzle Computational Design Methodology Development and Application

The Open National Combustion Code (OpenNCC) is used to simulate the aerospike exhaust nozzle region of a rotating detonation engine (RDE).The main objectives of the current study are twofold. The first goal is to validate the proposed computational methodology using the experimental data. The second goal is to demonstrate how the validated prediction tool can be used to optimize the nozzle geometry. To achieve a significant speed-up of computational time, the computational domain in divided into two parts: a combustion region and a throat-nozzle section. In the combustion region, a validated quasi-two-dimensional in-house code is utilized to generate an unsteady RDE flow field solution just upstream of the combustor throat. Subsequently, the unsteady flow data is fed into the three-dimensional throat-nozzle section as the inflow boundary condition. This facilitates the design optimization process since the unsteady inflow can be reused, and a relatively coarse mesh (i.e., larger time-step) can be used to analyze the flow fields around the nozzle. Five nozzle designs were studied and the predicted performance (i.e., thrust)compared. The optimized nozzle was found to produce 3.2% more overall thrust than a baseline nozzle design. Without the nozzle, there is a large low-pressure region at the throat exit, which significantly reduces the overall performance. This methodology is shown to be a promising approach to explore a wide variety of nozzle geometries in a relatively short amount of time.

CFD↗
NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗
NASA NTRSDate not supplied

Time Resolved Visualization of Liquid Jet Interaction With H2-Air Rotating Detonations Using MHz Rate Diesel PLIF

The characterization of the dynamic response of liquid jets to transient detonation wave passage is critical for optimization and modeling of liquid fueled rotating detonation combustors. In this work, a rotating detonation combustor (RDC) is operated on hydrogen and air to sustain stable detonation waves that acts as a detonation driver and interact in a one-way coupled manner with a single liquid fuel jet that propagates into the combustion chamber with cycle periods of ~ 250 μs. Diesel is utilized as a realistic fuel surrogate with higher aromatic compounds to enable fluorescence excitation, using the 355 nm thirdharmonic output of a burst-mode Nd:YAG laser, imaged at rates up to 1 MHz. By optimizing the technique to accommodate orders of magnitude variations in the fuel density throughout the injection process, the PLIF data enable quantitative measurements including the refill time, the relative recovery between liquid and gaseous jets and jet trajectory across various momentum flux ratio. As the passage of the detonation wave imparts significant changes in the momentum flux ratio, the qualitative liquid break-up process and spatial distribution varies significantly in time. As the injection system recovers ~ 70% of the cycle period and return to a quasi-steady position and allow comparisons with theoretical jet trajectories. These data, enabled by ultra-high-speed PLIF imaging, represent some of the first detailed measurements for quantifying the dynamic response and recovery of liquid jets exposed to periodic detonations in an operating RDC.

Propulsion↗
NASA NTRSDate not supplied

Liquid Jet Response to Detonation Waves in a Linear Detonation Combustor

The impact of periodic detonation wave impact on a liquid fuel jet is investigated in a linear detonation combustor. The linear detonation combustor operated with gaseous natural gas and oxygen generates sustained, self-excited detonation waves that propagate along its length at approximately 8 kHz, representing a wave propagation frequency in typical rocket rotating detonation engines. The effect of the detonation wave on the dynamic injection and break-up of a single diesel jet injected into the combustion chamber at varying injection pressures is evaluated with chemiluminescence, fuel planar laser induced fluorescence and Mie scattering measurements at 100 kHz. The detonation wave significantly impacts the liquid jet trajectory with its deflection in both windward and leeward direction as the adverse pressure gradient across it changes between wave passages. The maximum recovery height of the liquid jet is observed to be consistent across all operating conditions, and dependent on the detonation wave strength in the chamber.

propulsion↗
NASA NTRSDate not supplied

High-Speed Visualization of Spray Breakup in a Rotating Detonation Combustor Using Laser Induced Fluorescence

Rotating detonation engines (RDEs) represent a novel propulsion technology where incoming reactants are consumed by a self-sustaining detonation wave that travels azimuthally around an annular combustion chamber. In theory, the operating mode of these devices approximates a constant-volume combustion Humphry cycle. This represents a 5-15% increase in thermal efficiency over current rockets and air breathing systems operating on constant-pressure combustion Brayton cycles. The use of liquid fuels in RDEs represent unique challenges in terms of performance and operability. However, the fundamental physics involved in spray breakup, evaporation, and combustion are not well understood inside these devices. This research seeks to provide direct insight into these processes by adding a single liquid fuel injector into an otherwise hydrogen-air RDE to evaluate the breakup and refill dynamics. Visualization is performed by 200-1000 kHz laser induced fluorescence of liquid phase diesel (355 nm) and or kerosene (266 nm).

Detonation↗
NASA NTRSDate not supplied

Experimental and Computational Investigation of Valve Motion in a Resonant Pulse Combustor

The motion of a passive reed-type valve and a poppet-style valve operating in a small scale, liquid-fueled pulse combustor is investigated experimentally. Valve position and combustion chamber pressure are simultaneously measured using an in-house fabricated optical position probe. The reed valve configuration is found to operate in a self-aspirated mode, generating significant pressure gain. The poppet valve configuration cannot operate without forced air, and does not generate pressure gain. Both type valves are tested in combustors of multiple lengths. Close examination of the respective valve motions indicate that the reed valve is highly non-linear, with unique attributes that appear essential for self-aspiration. Dynamic models for the motion of each valve are implemented in a computational fluid dynamic (CFD) simulation of the pulse combustor in order to assess if this unique valve motion is critical to successful operation. The results show that it is. The implications of these results are discussed. The need for active actuation with feedback control, rather than passive valve actuation is highlighted as a critical technology for practical resonant pulse combustors.

Combustion↗
NASA NTRSDate not supplied

Characterization of an Optically Accessible RP/GOx Rotating Detonation Engine

The accurate characterization of the dynamic response of liquid jets to transient detonation wave passage is crucial for optimizing and modeling liquid-fueled rotating detonation combustors. To address this need, we have developed an optically accessible rocket RDE (RP-RDE), which utilizes liquid RP-1 and gaseous oxygen as propellants and operates at elevated pressures. The experimental setup features optical access from the oxidizer injection plenum to the combustor exit, allowing for detailed characterization of injection, mixing, and combustion processes and their impact on the detonation wave structure. To design and develop the liquid injection scheme for the RP-RDE test article, we employed a combined experimental and numerical approach that included cold-flow simulations. Our aim was to optimize the liquid injection process and ensure that the resulting fuel-oxidizer mixture is homogeneous and stable. To this end, high-speed optical imaging will be employed to provide qualitative visualization of the liquid and gaseous phases of the propellant as well as the local heat release during detonation wave propagation through the non-premixed medium. This work will provide critical insights into the behavior of the transient detonation waves in more relevant rocket conditions, which is essential for the optimization and modeling of rotating detonation combustors.

Propulsion↗