Engineering topics

Gutierrez, O. A.

Publications and source records attributed to Gutierrez, O. A..

At least 19 records

NASA NTRS1980

Effect of facility variation on the acoustic characteristics of three single stream nozzles

The characteristics of the jet noise produced by three single stream nozzles have been investigated statically at the NASA-Lewis Research Center outdoor jet acoustic facility. The nozzles consisted of a 7.6 cm diameter convergent conical, a 10.2 cm diameter convergent conical and an 8-lobe daisy nozzle with 7.6 cm equivalent diameter flow area. The acoustic experiments at NASA covered pressure ratios from 1.4 to 2.5 at total temperatures of 811 K and ambient. The data obtained with four different microphone arrays are compared.

Gutierrez, O. A.↗

NASA NTRS1980

Status of noise technology for advanced supersonic cruise aircraft

Developments in acoustic technology applicable to advanced supersonic cruise aircraft, particularly those which relate to jet noise and its suppression are reviewed. The noise reducing potential of high radius ratio, inverted velocity profile coannular jets is demonstrated by model scale results from a wide range of nozzle geometries, including some simulated flight cases. These results were verified statistically at large scale on a variable cycle engine (VCE) testbed. A preliminary assessment of potential VCE noise sources such as fan and core noise is made, based on the testbed data. Recent advances in the understanding of flight effects are reviewed. The status of component noise prediction methods is assessed on the basis of recent test data, and the remaining problem areas are outlined.

Stone, J. R.↗

NASA NTRS1980

Effect of facility variation on the acoustic characteristics of three single stream nozzles

The characteristics of the jet noise produced by three single stream nozzles were investigated statistically at the NASA-Lewis Research Center outdoor jet acoustic facility. The nozzles consisted of a 7.6 cm diameter convergent conical, a 10.2 cm diameter convergent conical and an 8-lobe daisy nozzle with 7.6 cm equivalent diameter flow area. The same nozzles were tested previously at cold flow conditions in other facilities such as the Royal Aircraft Establishment (RAE) 7.3 m acoustic wind tunnel. The acoustic experiments at NASA covered pressure ratios from 1.4 to 2.5 at total temperatures of 811 K and ambient. The data obtained with four different microphone arrays are compared. The results are also compared with data taken at the RAE facility and with a NASA prediction procedure.

Gutierrez, O. A.↗

NASA NTRS1979

Effects of geometric and flow-field variables on inverted-velocity-profile coaxial jet noise and source distributions

This paper presents relationships between the noise generation characteristics and the flow-field characteristics for inverted-velocity-profile coaxial jets. Noise measurements were made at four different sideline distances in order to determine the apparent noise source locations, and flow-field characteristics were determined from jet plume pressure/temperature surveys. These relationships are based on a published NASA Lewis prediction model, the basic assumptions of which are shown to be consistent with the experimental data reported herein. Improvements to the noise prediction procedure, on the basis of the present study, are included, which increase the accuracy of the high-frequency noise prediction.

Stone, J. R.↗

NASA NTRS1975

Forced-flow once-through boilers

A compilation and review of NASA-sponsored research on boilers for use in spacecraft electrical power generation systems is presented. Emphasis is on the heat-transfer and fluid-flow problems. In addition to space applications, much of the boiler technology is applicable to terrestrial and marine uses such as vehicular power, electrical power generation, vapor generation, and heating and cooling. Related research areas are discussed such as condensation, cavitation, line and boiler dynamics, the SNAP-8 project (Mercury-Rankine cycle), and conventional terrestrial boilers (either supercritical or gravity-assisted liquid-vapor separation types). The research effort was directed at developing the technology for once-through compact boilers with high heat fluxes to generate dry vapor stably, without utilizing gravity for phase separations. A background section that discusses, tutorially, the complex aspects of the boiling process is presented. Discussions of tests on alkali metals are interspersed with those on water and other fluids on a phenomenological basis.

Stone, J. R.↗

NASA NTRS1974

Noise of model target type thrust reversers for engine-over-the-wing applications

The present work reports on experiments concerning the noise generated by V-gutter and semicylindrical target reversers with circular and short-aspect-ratio slot nozzles having equivalent diameters of about 5 cm. At subsonic jet velocities of interest for engine-over-the-wing (OTW) powered-lift aircraft, the reversers were noisier than the nozzles alone and had a more uniform directional distribution and more high-frequency noise. Reverser shape was more important than nozzle shape in determining the reverser noise characteristics. An estimate is made of perceived noise level along the 152-m sideline for a hypothetical OTW powered-lift airplane.

Stone, J. R.↗

NASA NTRS1974

Performance of a model cascade thrust reverser for short-haul applications

Aerodynamic and acoustic characteristics are presented for a cowl-mounted, model cascade thrust reverser suitable for short-haul aircraft. Thrust reverser efficiency and the influence on fan performance were determined from isolated fan-driven models under static and forward velocity conditions. Cascade reverser noise characteristics were determined statically in an isolated pipe-flow test, while aerodynamic installation effects were determined with a wind-tunnel, fan-powered airplane model. Application of test results to short-haul aircraft calculations demonstrate that such a cascade thrust reverser may be able to meet both the performance and noise requirements for short-haul aircraft operation. However, aircraft installation effects can be quite significant.

Dietrich, D. A.↗

NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗

NASA NTRS1974

Performance of a model cascade thrust reverser for short-haul applications

Aerodynamic and acoustic characteristics are presented for a cowlmounted, model cascade thrust reverser suitable for short-haul aircraft. Thrust reverser efficiency and the influence on fan performance were determined from isolated fan-driven models under static and forward velocity conditions. Cascade reverser noise characteristics were determined statically in an isolated pipe-flow test, while aerodynamic installation effects were determined with a wind-tunnel, fan-powered airplane model. Application of test results to short-haul aircraft calculations demonstrated that such a cascade thrust reverser may be able to meet both the performance and noise requirements for short-haul aircraft operation. However, aircraft installation effects can be quite significant.

Dietrich, D. A.↗

NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power levels, directivity, and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches; pressure ratios ranged from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4.5- to 6-th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields.

Gutierrez, O. A.↗

NASA NTRS1974

Noise of model target type thrust reversers for engine-over-the-wing applications

The results of experiments on the noise generated by V-gutter and semicylindrical target reversers with circular and short-aspect-ratio slot nozzles having diameters of about 5 cm are presented. The experiments were conducted with cold-flow jets at velocities from 190-290 m/sec. The reversers at subsonic jet velocities had a more uniform noise distribution and higher frequency than the nozzles alone. The reverser shape was shown to be more important than the nozzle shape in determining the noise characteristics. The maximum sideline pressure level varied with the sixth power of the jet velocity, and the data were correlated for angles along the sideline. An estimate of the noise level along the 152 m sideline for an engine-over-the-wing powered-lift airplane was made.

Stone, J. R.↗

NASA NTRS1973

Assessment of jets as acoustic shields by comparison of single- and multitube suppressor nozzle data

Recent 1/4 scale and engine size nozzle acoustic data, for both 37-tube and single nozzles, are used to test the jet-shielding principle. At low jet velocities the multitube nozzle total sound power approaches the equivalent of 37 single tubes (no shielding), while near-sonic and above, the small equivalent number of single tubes compares well with a geometric model of lateral radiation from only about a third of the circumference of the outer jets (nearly complete shielding). At high jet velocities, the geometric shielding hypothesis is in excellent agreement with acoustic data from which the downstream coalesced jet-noise is excluded. Present results are compared with an existing correlation for single jets, and with previous publications on multijet shielding.

Gray, V. H.↗

NASA NTRS1973

Noise tests of a high-aspect-ratio slot nozzle with various V-gutter target thrust reversers

The results of experiments on the noise generated by a 1.33 x 91.4 cm slot nozzle with various V-gutter reversers are presented. The experiments were conducted with near-ambient temperature jets at nozzle pressure ratios of 1.25 to 3.0, yielding jet velocities of about 190 to 400 m/sec. At pressure ratios of 2 or less, the reversers, in addition to being noisier than the nozzle alone, also had a more uniform directional distribution and more high-frequency noise. At pressure ratios above 2, the nozzle alone generated enough shock noise that the levels were about the same as for the reversers. The maximum overall sound pressure level and the effective overall sound power level both varied with the sixth power of jet velocity over the range tested.

Stone, J. R.↗

NASA NTRS1973

Small-scale noise tests of a slot nozzle with V-gutter target thrust reverser

The noise generated by a 2.26- by 11.43-cm slot nozzle with a V-gutter reverser, as well as some aerodynamic data on flow, thrust-reversal efficiency, and nozzle jet velocity decay were studied. The experimental data are scaled up to sizes suitable for reversing the wing flow of a 45/400-kg augmentor-wing-type STOL airplane, yielding perceived noise levels well above the 95-PNdb design goal on the 152-m sideline. The reverser, in addition to being noisier than the nozzle alone, also had a more uniform directional distribution and more high frequency noise. The maximum overall sound pressure level and the effective sound power level both varied with the sixth power of nozzle jet velocity. Preliminary experiments indicated possible sideline noise reduction by shielding.

Stone, J. R.↗

NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 feet per second. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise. The total noise power generation was essentially the same for circular, slot, and plug nozzles of good aerodynamic shape. The noise radiation patterns were essentially the same for these nozzle shapes except near the nozzle exhaust axis.

Olsen, W. A.↗

NASA NTRS1973

Assessment of jets as acoustic shields by comparison of single- and multitube suppressor nozzle data

Recent 1/4 scale and engine size nozzle acoustic data, for both 37-tube and single nozzles, were used to test the jet-shielding principle. At low jet velocities the multitube nozzle total sound power approaches the equivalent of 37 single tubes (no shielding), while near-sonic and above, the small equivalent number of single tubes compares well with a geometric model of lateral radiation from only about a third of the circumference of the outer jets (nearly complete shielding). At high jet velocities, the geometric shielding hypothesis is in excellent agreement with acoustic data from which the downstream coalesced jet noise is excluded. Present results are compared with an existing correlation for single jets, and with previous publications on multijet shielding.

Gray, V. H.↗

NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise.

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 ft/sec. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise.

Olsen, W. A.↗

NASA NTRS1973

Noise tests of a high-aspect-ratio slot nozzle with various V-gutter target thrust reversers

The results of experiments on the noise generated by a 1.33- by 91.4 cm slot nozzle with various V-gutter reversers, and some thrust measurements are presented. The experiments were conducted with near-ambient temperature jets at nozzle pressure ratios of 1.25 to 3.0, yielding jet velocities of about 190 to 400 m/sec. At pressure ratios of 2 or less, the reversers, in addition to being noisier than the nozzle alone, also had a more uniform directional distribution and more high-frequency noise. At pressure ratios above 2, the nozzle alone generated enough shock noise that the levels were about the same as for the reversers. The maximum overall sound pressure level and the effective overall sound power level both varied with the sixth power of jet velocity over the range tested. The data were scaled up to a size suitable for reversing the wing-flap slot nozzle flow of a 45 400-kg augmentor-wing-type airplane on the ground, yielding perceived noise levels well above 95 PNdB on a 152-m sideline.

Stone, J. R.↗