Engineering Papers⌕ Search

Engineering topics

Gustafson, D. E.

Publications and source records attributed to Gustafson, D. E..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Formation of Y(x)Nd(1-x) Ba2Cu3O(7-delta) (0 = or < x < or = 0.7) Superconductors from an Undercooled Melt Via Aero-Acoustic Levitation

Melt processing of RE123 superconductors has gained importance in recent years. While the first high temperature superconductors (HTSCs) were made using traditional ceramic press and sinter technology, recent fabrication efforts have employed alternate processing techniques including laser ablation and ion beam assisted deposition for thin film fabrication of tapes and wires and melt growth for bulk materials. To optimize these techniques and identify other potential processing strategies, phase relation studies on HTSCs have been conducted on a wide variety of superconducting compounds using numerous processing strategies. This data has enhanced the understanding of these complex systems and allowed more accurate modeling of phase interactions. All of this research has proved useful in identifying processing capabilities for HTSCs but has failed to achieve a breakthrough for wide spread application of these materials. This study examines the role of full to partial substitution of Nd in the Y123 structure under rapid solidification conditions. Aero-acoustic levitation (AAL) was used to levitate and undercool RE123 in pure oxygen binary alloys with RE = Nd an Y along a range of compositions corresponding to Y(x)Nd(1-x) Ba2Cu3O(7-delta) (0 = or < x < or = 0.7) which were melted by a CO2 laser. Higher Y content spheres could not be melted in the AAL and were excluded from this report. Solidification structures were examined using scanning electron microscopy, electron dispersive spectroscopy, and powder x-ray diffraction to characterize microstructures and identify phases.

Gustafson, D. E.↗
NASA NTRS1983

Current status of system identification methodology

Large space structures, system identification, model formulation, experimental design, model order and structure determination, parameter estimation, reduced order modeling, and closed loops are considered.

Larimore, W. E.↗
NASA NTRS1979

Applications of estimation theory to inverse problems in meteorology

The paper applies iterated and non-iterated extended Kalman filters to solve two practical meteorological inversion problems. Passive microwave satellite soundings are used to infer vertical temperature profiles and cloud parameters. In both cases it is shown that improvements can be obtained over presently used techniques. Finally, the results suggest that modern multivariate nonlinear recursive estimation techniques based in a Bayesian methodology can be a valuable tool in the area of remote sounding of atmospheric parameters.

Gustafson, D. E.↗
NASA NTRS1976

Linear minimum variance filters applied to carrier tracking

A new approach is taken to the problem of tracking a fixed amplitude signal with a Brownian-motion phase process. Classically, a first-order phase-lock loop (PLL) is used; here, the problem is treated via estimation of the quadrature signal components. In this space, the state dynamics are linear with white multiplicative noise. Therefore, linear minimum-variance filters, which have a particularly simple mechanization, are suggested. The resulting error dynamics are linear at any signal/noise ratio, unlike the classical PLL. During synchronization, and above threshold, this filter with constant gains degrades by 3 per cent in output rms phase error with respect to the classical loop. However, up to 80 per cent of the maximum possible noise improvement is obtained below threshold, where the classical loop is nonoptimum, as demonstrated by a Monte Carlo analysis. Filter mechanizations are presented for both carrier and baseband operation.

Gustafson, D. E.↗
NASA NTRS1972

Station-keeping guidance

The station-keeping guidance system is described, which is designed to automatically keep one orbiting vehicle within a prescribed zone fixed with respect to another orbiting vehicle. The active vehicle, i.e. the one performing the station-keeping maneuvers, is referred to as the shuttle. The other passive orbiting vehicle is denoted as the workshop. The passive vehicle is assumed to be in a low-eccentricity near-earth orbit. The primary navigation sensor considered is a gimballed tracking radar located on board the shuttle. It provides data on relative range and range rate between the two vehicles. Also measured are the shaft and trunnion axes gimbal angles. An inertial measurement unit (IMU) is provided on board the orbiter. The IMU is used at all times to provide an attitude reference for the vehicle. The IMU accelerometers are used periodically to monitor the velocity-correction burns applied to the shuttle during the station-keeping mode. The guidance system is capable of station-keeping the shuttle in any arbitrary position with respect to the workshop by periodically applying velocity-correction pulses to the shuttle.

Gustafson, D. E.↗