Engineering topics

Guo, Wei

Publications and source records attributed to Guo, Wei.

27 records · Page 2

DOE OSTI2022

Decoupling mass transport and electron transfer by a double-cathode structure of a Li-O 2 battery with high cyclic stability

Aprotic lithium-oxygen (Li-O 2 ) batteries have attracted extensive attention due to their ultrahigh theoretical energy density. However, slow and undesired electron transfer during cathodic reactions causes low cyclic stability in these batteries. Here, in this paper, we demonstrate that O 2 mass transport and electron transfer for cathodic reactions in Li-O 2 batteries could be decoupled by a double-cathode structure that efficiently enables stable electron transfer between the cathode and Li 2 O 2 /O 2 . This resolves various side reactions and slow Li 2 O 2 reaction kinetics issues in conventional Li-O 2 batteries, leading to stable operation of the cell for nearly 2 months at a capacity of 0.2 and 5 mAh cm -2 , with more than 4- and 10-fold increases in cycle life when compared with single-cathode batteries. These remarkable improvements in the cyclic stability of Li-O 2 batteries with double cathodes provide an interesting concept for improving the operational stability of other metal-rechargeable batteries with conversion-type chemistry.

25 ENERGY STORAGE↗

DOE OSTI2022

Beyond Simple Dilution: Superior Conductivities from Cosolvation of Acetonitrile/LiTFSI Concentrated Solution with Acetone

Concentrated solutions of Li salts in acetonitrile are promising alternative electrolytes for the next generation of Li batteries as they may exhibit superior electrochemical properties. However, the reduced mobility of the chemical species is a barrier yet to be overcome, and for this, we explore the utilization of acetone as a cosolvent. Although acetone is a polar compound, we find that its addition to the LiTFSI/acetonitrile solution does not follow the trends expected for a simple dilution process. At a low concentration, acetone subtly shifts acetonitrile from the first to extended solvation sheaths of the ions. Still, most of the original structure of the solution is preserved, and mobile high-concentration clusters are formed in the solution. At higher concentrations, the cosolvation promotes cation–anion interactions but with a different nature from those in the original solution and still allows for a further increase in conductivity. Additionally, the non-coordinating fraction of acetonitrile acquires features resembling the pure solvent, which is a possible additional facilitating factor for ionic diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

A Modeling Tool to Analyze the Performance of Industrial Cooling Towers

Energy efficiency and energy savings have become an important factor as industries look for ways to save energy and minimize their energy consumption while reducing their carbon footprint. Cooling towers are utilized significantly in industries for either serving chillers or process cooling. Depending on the size of the cooling tower, it can use a surprising amount of energy and water, which is why it is crucial to make sure that the facility has optimized their cooling tower.A modeling tool has been developed to perform a thorough analysis of a cooling tower and its various operations to ensure that the facility has optimized its cooling tower. This model analyzes an annual base case in comparison with the revised case of a cooling tower operation. This modeling tool simulates 8,760 hourly calculations for fan power for various fan controls, water consumption, and pumping energy consumption and demand based on the user’s location and its corresponding Typical Meteorological Year 3 (TMY3) weather data. This model is capable to simulate up to five cooling tower cells as one large tower utilizing one pump or parallel pumping. The successful validated cooling tower model should assist industry to save energy at their facility through their cooling tower, whether they use it for process cooling or heating, ventilation and air conditioning (HVAC) applications. The entering/leaving water temperatures based on a monthly operating schedule or a wet-bulb temperature schedule will be used as inputs, and the model can calculate savings in energy for various conditions including variable-frequency drive (VFD) on the fan/pump, drift eliminators, number of cycles of concentration, reduced water flow rate, etc.

Hooper, Josh↗

DOE OSTI2021

A bifunctional zeolitic porous liquid with incompatible Lewis pairs for antagonistic cascade catalysis

The emergence of porous liquids (PLs) opened opportunities to form unique antagonistic systems capable of fulfilling cascade reactions promoted by incompatible active sites in one pot, which is a long-term challenging subject in catalysis. Herein, unique bifunctional type III PL-based systems were facilely fabricated via assembly of zeolite nanosheets with ionic liquids. Rational structural design afforded PLs that feature high zeolite concentration, stable dispersion after 2 years, abundant cavity distribution, and involvement of antagonistic groups (acid and base sites) in separated and active form via steric hindrance control and electronic repulsion regulation. These unique properties worked cooperatively to fulfill the cascade deacetalization-Knoevenagel/Aldol condensation in one pot with superior catalytic efficiency outperforming the traditional systems. The key to success lies in the formation of bifunctional composites, transformation of zeolite from heterogeneous to homogeneous via surface modification, as well as rapid mass transfer ensured by the rigid porous architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Heat and mass transfer during a sudden loss of vacuum in a liquid helium cooled tube - Part III: Heat deposition in He II

A sudden loss of vacuum can be catastrophic for superconducting particle accelerators. In such an event, air leaks into the liquid-helium-cooled accelerator beamline tube and condenses on its inner surface, causing rapid boiling of the helium and dangerous pressure build-up. Understanding the coupled heat and mass transfer processes is important for the design of the beamline cryogenic system. Our past experimental study on nitrogen gas propagating in a copper tube cooled by normal liquid helium (He I) has revealed a nearly exponential slowing down of the gas front. A theoretical model that accounts for the interplay of the gas dynamics and the condensation was developed, which successfully reproduced various key observations. However, since many accelerator beamlines are actually cooled by superfluid helium (He II) in which the heat transfer is via a non-classical thermal counterflow mode, we need to extend our work to the He II cooled tube. This paper reports our systematic measurements using He II and the numerical simulations based on a modified model that accounts for the He II heat-transfer characteristics. By tuning the He II peak heat-flux parameter in our model, we have reproduced the observed gas dynamics in all experimental runs. The fine-tuned model is then utilized to reliably evaluate the heat deposition in He II. Finallly, this work not only advances our understanding of condensing gas dynamics but also has practical implications to the design codes for beamline safety.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Benchmark CO 2 separation achieved by highly fluorinated nanoporous molecular sieve membranes from nonporous precursor via in situ cross-linking

Molecular sieve membranes with rigid micropores and CO 2 -philic functionalities within the architectures are promising candidates in CO 2 separation. However, the development of ctieve approaches for their fabrication still remains a significant challenge. In this study, an in situ cross-linking strategy is developed for the preparation of nanoporous fluorinated moleffecular sieve membranes using commercially available dense and non-porous polystyrene (M PS ) as a precursor template. Based on the dehydrative Friedel-Crafts reactions with highly fluorinated benzylic alcohols, M PS membranes are cross-linked in situ upon exposure to Brønsted acid (CF 3 SO 3 H), affording fluorinated microporous polymeric membranes with surface areas up to 523 m 2 g –1 and the presence of micropores centered at 1.1–1.3 nm as well as ultra-micropores (~0.6 nm). The obtained modified membranes exhibit good ideal CO 2 permeability of 797 barrer and CO 2 /N 2 selectivity of 28.5. In addition, high fluorine content (up to 28.5 wt%) and good thermal stability made the cross-linked membranes promising candidates to produce fluorinated carbon molecular sieve membranes with improved textural properties, exhibiting surface areas up to 1020 m 2 g –1 and ultra-micropores of ~0.4 nm. These membranes achieve superior CO 2 /N 2 separation performances exceeding the Robeson upper bound limit (2008).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Operando leaching of pre-incorporated Al and mechanism in transition-metal hybrids on carbon substrates for enhanced charge storage

Insufficient exposure and utilization of active sites often induces an inferior reactivity for transition-metal-based two-dimensional (2D) materials. In response, we for the first time propose a universal "nano-tailoring" strategy to incorporate abundant defects and active sites into low-crystallinity nanosheets by electrochemically leaching of Al species. With MnAl layered double hydroxides (LDHs) as a representative example, potassium-birnessite MnO 2 (AK-MnO 2 ) with oxygen vacancies and abundant edge sites is successfully produced. The oxygen vacancies are shown to help optimize the electron-transfer and ion-adsorption capability. These integrated advantages endow the AK-MnO 2 with a high capacitance value of 239 F g –1 at 100 A g –1 . By further combining with soft X-ray absorption spectroscopy techniques, we unravel that the reducibility of M 2+ in M 2+ Al-LDH serves as the key descriptor for the reconstruction rate. Here, this "nano-tailoring" strategy can provide some important implications and clues to manipulating 2D materials for efficient energy storage and conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1993

The limit of frequency estimation

In phase and frequency measurements, the measured phase and frequency are not the true phase and frequency but the ones which are disturbed by noises, due to the effects of the noise processes. The effects of three noise processes, i.e., White PM, White FM, and Random Walk FM, on the estimations of phase and frequency is discussed. It is indicated that the properties of these two estimations are very different. In phase estimation, the error can be reduced by properly selecting suitable smoothing length NT and smaple interval T. But in frequency estimation, the error cannot be reduced arbitrarily by means of improving estimator or measurement equipment. The precision of frequency is limited by the intrinsic noises in the clock.

Guo, Wei↗

NASA NTRS1991

Variable temperature pressure broadening of HNO3 in the millimeter wave spectral region

Measurements were performed for both O2 and N2 broadening in the 100-380 K temperature range by using a heated equilibrium cell for elevated temperatures and the utilization of a collisionally cooled cell at the lower temperatures where HNO3 has a small vapor pressure. Observed pressure-broadening data can be fit to the normal empirical law, giving n values between 0.62 and 0.84.

Goyette, Thomas M.↗