Engineering topics

Grob, Lisa M.

Publications and source records attributed to Grob, Lisa M..

3 records

NASA NTRS2018

Considerations When Building Thermal Models that Require Conversion Between Formats

At times, it is inevitable to require conversion of thermal models from one software format to another. This most often occurs for missions with international partners where not all parties utilize the same software packages for thermal analysis. Mandating a single tool for all parties is one possible solution, but this approach can introduce problems if significant effort is required to overcome inexperience with the designated tool and may result in difficulty meeting analysis schedule requirements. Alternatively, allowing all parties to use their own familiar tools minimizes the impact to analysis schedules but does introduce the need to convert the models later to a common format for analysis at a higher level of assembly. External conversion tools and formats have been developed through the years to aid in this process, but have had limited success in fully converting models seamlessly. Having a basic familiarity with tool capabilities on both sides of the conversion process allows for models to be built in a manner to better facilitate conversion by avoiding features and capabilities which are unsupported by the destination tool or for which no workarounds exist. Also, the effort to convert a model is often neglected when developing the schedules for analysis at the higher assembly levels; delivery of models preconditioned for convertibility minimizes the schedule risk. This paper seeks to provide some guidance on modeling techniques to avoid when developing Geometrical Math Models (GMM) and Thermal Math Models (TMM) when conversion is required. The recommendations are based on GMM conversion experiences between TSS/ThermalDesktop/ESARAD and TMM conversions between SINDA-FLUINT/ESATAN.

Modeling↗

NASA NTRS2000

Parametric Study of Variable Emissivity Radiator Surfaces

The goal of spacecraft thermal design is to accommodate a high function satellite in a low weight and real estate package. The extreme environments that the satellite is exposed during its orbit are handled using passive and active control techniques. Heritage passive heat rejection designs are sized for the hot conditions and augmented for the cold end with heaters. The active heat rejection designs to date are heavy, expensive and/or complex. Incorporating an active radiator into the design that is lighter, cheaper and more simplistic will allow designers to meet the previously stated goal of thermal spacecraft design Varying the radiator's surface properties without changing the radiating area (as with VCHP), or changing the radiators' views (traditional louvers) is the objective of the variable emissivity (vary-e) radiator technologies. A parametric evaluation of the thermal performance of three such technologies is documented in this paper. Comparisons of the Micro-Electromechanical Systems (MEMS), Electrochromics, and Electrophoretics radiators to conventional radiators, both passive and active are quantified herein. With some noted limitations, the vary-e radiator surfaces provide significant advantages over traditional radiators and a promising alternative design technique for future spacecraft thermal systems.

Grob, Lisa M.↗

NASA NTRS2000

Variable Emissivity Through MEMS Technology

This paper discusses a new technology for variable emissivity (vari-e) radiator surfaces, which has significant advantages over traditional radiators and promises an alternative design technique for future spacecraft thermal control systems. All spacecraft rely on radiative surfaces to dissipate waste heat. These radiators have special coatings, typically with a low solar absorptivity and a high infrared-red emissivity, that are intended to optimize performance under the expected heat load and thermal sink environment. The dynamics of the heat loads and thermal environment make it a challenge to properly size the radiator and often require some means of regulating the heat rejection rate of the radiators in order to achieve proper thermal balance. Specialized thermal control coatings, which can passively or actively adjust their emissivity offer an attractive solution to these design challenges. Such systems would allow intelligent control of the rate of heat loss from a radiator in response to heat load and thermal environmental variations. Intelligent thermal control through variable emissivity systems is well suited for nano and pico spacecraft applications where large thermal fluctuations are expected due to the small thermal mass and limited electric resources. Presently there are three different types of vari-e technologies under development: Micro ElectroMechanical Systems (MEMS) louvers, Electrochromic devices, and Electrophoretic devices. This paper will describe several prototypes of micromachined (MEMS) louvers and experimental results for the emissivity variations measured on theses prototypes. It will further discuss possible actuation mechanisms and space reliability aspects for different designs. Finally, for comparison parametric evaluations of the thermal performances of the new vari-e technology and standard thermal control systems are presented in this paper.

Darrin, Ann Garrison↗