Engineering topics

Gregory, John C.

Publications and source records attributed to Gregory, John C..

At least 37 records · Page 2

NASA NTRS1992

Radioactive 7Be materials flown on LDEF

Following the discovery of the atmospheric cosmogenic radionuclide Be-7 on the Long Duration Exposure Facility (LDEF), we began a search for other known nuclides produced by similar mechanisms. None of the others have the narrow gamma-ray line emission of Be-7 decay which enable its rapid detection and quantification. A search for Be-10 atoms on LDEF clamp plates using accelerator mass spectrometry is described. An unexpected result was obtained.

Gregory, John C.↗

NASA NTRS1992

Flouorescence measurements of the thermal control coatings on LDEF experiments S0069 and A0114

Strong fluorescence emissions were observed, during post flight ultraviolet light inspection of experiments S0069 and A0114, from some of the surfaces exposed to the space environment. Subsequent wavelength measurements of the fluorescence emission characteristics, indicated large changes occurred between controls and exposed materials. Black urethane based coatings, especially ones having a silicone atomic oxygen protective overcoat, appear bright yellow under ultraviolet exposure. Measurements showed that the urethane based coatings had their emission spectra shifted into the visible wavelength range. In contrast, zinc oxide pigment type coatings showed a different effect, which was a quenching or reduction of their fluorescence versus exposure time. Silver Teflon bonded to aluminum with acrylic adhesive also showed a slight measurable fluorescence, which was found to originate in the acrylic adhesive.

Zwiener, James M.↗

NASA NTRS1992

Angular distributions of 5eV atomic oxygen scattered from solid surfaces on the LDEF satellite

The angular distribution of 5eV atomic oxygen scattered off several smooth solid surfaces was measured by experiment A0114 which flew on board the Long Duration Exposure Facility (LDEF). Target surfaces were silver, vitreous carbon, and lithium fluoride crystal. The apparatus was entirely passive. It used the property of silver surfaces to absorb oxygen atoms with high efficiency; the silver is converted to optically transmissive silver oxide. A collimated beam of oxygen atoms is allowed to fall on the target surface at some pre-set angle. Reflected atoms are then intercepted by a silver film placed so that it subtends a considerable solid angle from the primary beam impact on the target surface. The silver films are evaporated onto flexible optically-clear polycarbonate sheets which are scanned later to determine oxygen uptake. While the silver detector cannot measure atom velocity or energy, its physical configuration allows easy coverage of large angular space both in the beam-plane (that which includes the incident beam and the surface normal), and in the azimuthal plane of the target surface.

Gregory, John C.↗

NASA NTRS1992

Interaction of atomic oxygen with thin film and bulk copper: An XPS, AES, XRD, and profilometer study

The University of Alabama in Huntsville (UAH) experiment A-0114 was designed primarily to study degradation of material surfaces due to low earth orbital (LEO) atmospheric oxygen. The experiment contained 128 one inch circular samples: metals, polymers, carbons, and semiconductors. Among metal samples, copper has shown some interesting new results. Two types of copper samples, a film sputter coated on fused silica and a bulk piece of OFHC copper, were characterized employing a variety of techniques such as X-ray and Auger electron spectroscopies, X-ray diffraction, and high resolution profilometry. Cu 2p core level spectra were used to characterize the presence of Cu2O and CuO in addition to Cu Auger LMM lines. These results are supported by our recent X-ray diffraction studies which clearly establish the presence of Cu oxides which we were unable to prove in our earlier work. Profilometry showed an increase in thickness of the film sample where exposed to 106.7 +/- 0.5 nm from an initial thickness of 74.2 +/- 1.1 nm. Further studies with SEM and ellipsometry are underway.

Raikar, Genesh N.↗

NASA NTRS1992

Analysis of surfaces from the LDEF A0114, phase 2

Analysis of surfaces from the Long Duration Exposure Facility (LDEF) continued during the reporting period. Work has continued on profilometry measurements of eroded and corroded sample surfaces, optical transmission measurements, analysis of the pinhole camera, and x-ray photoelectron spectroscopy (XPS) analysis of some samples. Papers that have appeared or have been accepted for publications are listed. Several of these papers and an abstact are included.

Gregory, John C.↗

NASA NTRS1992

Erosion rates for polymers measured on LDEF

The summary and viewgraphs of work presented at the Long Duration Exposure Facility (LDEF) materials workshop are given. Experimental data for erosion depths and rates for polymers measured on LDEF are given. In general, agreement is reasonably good between erosion rates from the University of Alabama in Huntsville (UAH) LDEF experiment and prior data obtained at much lower mission fluences. Agreement is particularly satisfying in the case of Kapton where the prior data base is large. In spite of the known presence of silicaceous contamination on LDEF surfaces, the erosion rates of the highly erodible materials are hardly affected, if at all. Graphs showing changes in optical properties (reflectance and transmittance) of metal films are included.

Gregory, John C.↗

NASA NTRS1992

Pinhole cameras as sensors for atomic oxygen in orbit: Application to attitude determination of the LDEF

Images produced by pinhole cameras using film sensitive to atomic oxygen provide information on the ratio of spacecraft orbital velocity to the most probable thermal speed of oxygen atoms, provided the spacecraft orientation is maintained stable relative to the orbital direction. Alternatively, information on the spacecraft attitude relative to the orbital velocity can be obtained, provided that corrections are properly made for thermal spreading and a corotating atmosphere. The Long Duration Exposure Facility (LDEF) orientation, uncorrected for a corotating atmosphere, was determined to be yawed 8.0 +/- 0.4 degrees from its nominal attitude, with an estimated +/- 0.35 degree oscillation in yaw. The integrated effect of inclined orbit and corotating atmosphere produces an apparent oscillation in the observed yaw direction, suggesting that the LDEF attitude measurement will indicate even better stability when corrected for a corotating atmosphere. The measured thermal spreading is consistent with major exposure occurring during high solar activity, which occurred late during the LDEF mission.

Peters, Palmer N.↗

NASA NTRS1992

Measurements of erosion characteristics for metal and polymer surfaces using profilometry

The surfaces of many materials exposed in low earth orbit are modified due to interaction with atomic oxygen. Chemical changes and surface roughening effects can occur which alter optical and other properties. The experiment A0114 contained 128 solid surface samples, half of which were exposed on the front and half on the rear of LDEF. Each sample has been subjected to many analyses, but only the methods and techniques used to measure the changes in roughness, erosion depths, and material growth using profilometry are described.

Christl, Ligia C.↗

NASA NTRS1992

Interactions of atomic oxygen with material surfaces in low Earth orbit: Preliminary results from experiment A0114

The atomic oxygen experiment consisted of two trays (one-sixth of a Long Duration Exposure Facility (LDEF) tray each) of 64 one inch diameter solid samples. It was intended that the effects of atomic oxygen and solar ultraviolet irradiation on the surface properties of each material could be distinguished from each other and from the effects of aging. Sixteen of the samples were placed on a thermally isolated plate of highly polished aluminum, while the main plate was coated with the thermal control coating S13-GLO. Though the experiment was entirely passive, it was hoped that the effects of thermal activation might be observed, if present. The plates were expected to stabilize at temperatures differing by 20-30 C. The samples included thin films of metals Os, Ir, Pt, Ni, Mo, and Al coated onto silica optical flats, metal carbides (WC, SiC), solid carbons of various types, eight polymers, and some other coatings of various types. Analysis is essentially complete using stylus profilometry with high sensitivity Talystep and lower sensitivity Talysurf machines. Though the integrated fluence of O atoms on the LDEF was 30 times that of previous missions, etch depths of the polymers such as the polyimide Kapton show excellent agreement with extrapolations from previous flight data. However, some new effects were observed. We demonstrated on a previous experiment on STS-8 that profilometry of this kind can show steps of 50 A (for example those due to oxide film growth on metals) and this is now the preferred method for estimating etch depth (or mass loss) of erodible substances.

Gregory, John C.↗

NASA NTRS1992

Effects on LDEF exposed copper film and bulk

Two forms of copper were exposed to the Long Duration Exposure Facility (LDEF) Mission 1 environment: a copper film initially 74.2 plus or minus 1.1 nm thick sputter coated on a fused silical flat and a bulk piece of oxygen free, high conductivity (OFHC) copper. The optical density of the copper film changed from 1.33 to 0.70 where exposed and the film thickness increased to 106.7 plus or minus 0.5 nm where exposed. The exposed area appears purple by reflection and green by transmission for the thin film and maroon color for the bulk copper piece. The exposed areas increased in thickness, but only increase in the thickness of thin film samples could be readily measured. The increase in film thickness is consistent with the density changes occurring during conversion of copper to an oxide. However, we have not been able to confirm appreciable conversion to an oxide by x ray diffraction studies. We have not yet subjected the sample to e-beams or more abusive conditions out of concern that the film might be modified.

Peters, Palmer N.↗

NASA NTRS1992

The emulsion chamber technology experiment

Photographic emulsion has the unique property of recording tracks of ionizing particles with a spatial precision of 1 micron, while also being capable of deployment over detector areas of square meters or 10's of square meters. Detectors are passive, their cost to fly in Space is a fraction of that of instruments of similar collecting. A major problem in their continued use has been the labor intensiveness of data retrieval by traditional microscope methods. Two factors changing the acceptability of emulsion technology in space are the astronomical costs of flying large electronic instruments such as ionization calorimeters in Space, and the power and low cost of computers, a small revolution in the laboratory microscope data-taking. Our group at UAH made measurements of the high energy composition and spectra of cosmic rays. The Marshall group has also specialized in space radiation dosimetry. Ionization calorimeters, using alternating layers of lead and photographic emulsion, to measure particle energies up to 10(exp 15) eV were developed. Ten balloon flights were performed with them. No such calorimeters have ever flown in orbit. In the ECT program, a small emulsion chamber was developed and will be flown on the Shuttle mission OAST-2 to resolve the principal technological questions concerning space exposures. These include assessments of: (1) pre-flight and orbital exposure to background radiation, including both self-shielding and secondary particle generation; the practical limit to exposure time in space can then be determined; (2) dynamics of stack to optimize design for launch and weightlessness; and (3) thermal and vacuum constraints on emulsion performance. All these effects are cumulative and affect our ability to perform scientific measurements but cannot be adequately predicted by available methods.

Gregory, John C.↗

NASA NTRS1992

Electron spectroscopy analysis

The Surface Science Laboratories at the University of Alabama in Huntsville (UAH) are equipped with x-ray photoelectron spectroscopy (XPS or ESCA) and Auger electron spectroscopy (AES) facilities. These techniques provide information from the uppermost atomic layers of a sample, and are thus truly surface sensitive. XPS provides both elemental and chemical state information without restriction on the type of material that can be analyzed. The sample is placed into an ultra high vacuum (UHV) chamber and irradiated with x-rays which cause the ejection of photoelectrons from the sample surface. Since x-rays do not normally cause charging problems or beam damage, XPS is applicable to a wide range of samples including metals, polymers, catalysts, and fibers. AES uses a beam of high energy electrons as a surface probe. Following electronic rearrangements within excited atoms by this probe, Auger electrons characteristic of each element present are emitted from the sample. The main advantage of electron induced AES is that the electron beam can be focused down to a small diameter and localized analysis can be carried out. On the rastering of this beam synchronously with a video display using established scanning electron microscopy techniques, physical images and chemical distribution maps of the surface can be produced. Thus very small features, such as electronic circuit elements or corrosion pits in metals, can be investigated. Facilities are available on both XPS and AES instruments for depth-profiling of materials, using a beam of argon ions to sputter away consecutive layers of material to reveal sub-surface (and even semi-bulk) analyses.

Gregory, John C.↗

NASA NTRS1991

Analysis of surfaces from the LDEF A0114, phase 4

Progress made from 1 Mar. to 31 Aug. 1991 is presented. The work concentrated on profilometry measurements of eroded and corroded sample surfaces, optical transmission measurements, analysis of the pinhole camera, and x-ray photoelectron spectroscopic (XPS) analysis of some samples. The following papers are presented: (1) observation of Be-7 on the surface of the Long Duration Exposure Facility (LDEF) Spacecraft; (2) measurement of the passive attitude control performance of a recovered spacecraft; (3) effects on LDEF exposed copper flim and bulk; (4) measurements of erosion characteristics for metal and polymer surfaces using profilometry; (5) the interactions of atmospheric cosmogenic radionuclides with spacecraft surfaces; (6) pinhole cameras as sensors for atomic oxygen in orbit; and (7) interaction of atomic oxygen with solid surfaces in low earth orbit- results from LDEF experiment A0114.

Gregory, John C.↗

NASA NTRS1991

The interactions of atmospheric cosmogenic radionuclides with spacecraft surfaces

The discovery of the cosmogenic radionuclide Be-7 on the front surface (and the front surface only) of the Long Duration Exposure Facility (LDEF) spacecraft has opened opportunities to investigate new phenomena in several disciplines of space science. The experiments performed for this work show that the Be-7 results only if the source of the isotope is the atmosphere through which the spacecraft passed. We should expect that the uptake of beryllium in such circumstances will depend on the chemical form of the Be and the chemical nature of the substrate. It was found that the observed concentration of Be-7 does, in fact, differ between metal surfaces and organic surfaces such as PTFE (teflon). It is noted, however, that: (1) organic surfaces, even PTFE, are etched by the atomic oxygen found under these orbital conditions, and (2) the relative velocity of the species is 8 km(exp -1)s relative to the surface and the interaction chemistry and physics may differ from the norm. The Be-7 is formed by spallation of O and N nuclei under cosmic ray proton bombardment. The principal source region is at altitudes of 12-15 km. While very small quantities are produced above 300 km, the amount measured on the LDEF was 3 to 4 orders of magnitude higher than expected from production at orbital attitude. The most reasonable explanation is that Be-7 is rapidly transported from low altitudes by some unknown mechanism. The process must take place on a time scale similar to the half-life of the isotope (53 days). Many other isotopes are produced by cosmic ray reactions, and some of these are suited to measurement by the extremely sensitive methods of accelerator mass spectrometry. A program was initiated to search for these isotopes and it is hoped that such studies will provide new methods for studying mixing in the upper atmosphere.

Gregory, John C.↗

NASA NTRS1991

Effects on LDEF exposed copper film and bulk

Two forms of copper were exposed to the Long Duration Exposure Facility (LDEF) Mission 1 environment: a copper film, initially 74.2 plus or minus 1.1 nm thick sputter coated on a fused silica flat and a bulk piece of oxygen-free, high conductivity (OFHC) copper. The optical density of the copper film changed from 1.33 to 0.70 where exposed, and the film thickness increased to 106.7 plus or minus 0.5 nm where exposed. The exposed area appears purple by reflection and green by transmission for the thin film and maroon color for the bulk copper piece. The exposed areas increased in thickness, but only increase in the thickness of the thin film sample could be readily measured. The increase in film thickness is consistent with the density changes occurring during conversion of copper to an oxide. However, we have not been able to confirm appreciable conversion to an oxide by x-ray diffraction studies. We have not yet subjected the sample to e-beams or more abusive investigations out of concern that the film might be modified.

Peters, Palmer N.↗

NASA NTRS1991

Measurements of erosion characteristics for metal and polymer surfaces using profilometry

The surfaces of many materials exposed in low earth orbit are modified due to interaction with atomic oxygen. Chemical changes and surface roughening effects can occur which alter optical and other properties. The experiment A0114 contained 128 solid surface samples, half of which were exposed on the front and half on the rear of Long Duration Exposure Facility. Each sample was subjected to many analyses, but only the methods and techniques are described which were used to measure the changes in roughness, erosion depths, and material growth using profilometry.

Christl, Ligia C.↗

NASA NTRS1991

Pinhole cameras as sensors for atomic oxygen in orbit; application to attitude determination of the LDEF

Images produced by pinhole cameras using film sensitive to atomic oxygen provide information on the ratio of spacecraft orbital velocity to the most probable thermal speed of oxygen atoms, provided the spacecraft orientation is maintained stable relative to the orbital direction. Alternatively, as it is described, information on the spacecraft attitude relative to the orbital velocity can be obtained, provided that corrections are properly made for thermal spreading and a co-rotating atmosphere. The LDEF orientation, uncorrected for a co-rotating atmosphere, was determined to be yawed 8.0 minus/plus 0.4 deg from its nominal attitude, with an estimated minus/plus 0.35 deg oscillation in yaw. The integrated effect of inclined orbit and co-rotating atmosphere produces an apparent oscillation in the observed yaw direction, suggesting that the LDEF attitude measurement will indicate even better stability when corrected for a co-rotating atmosphere. The measured thermal spreading is consistent with major exposure occurring during high solar activity, which occurred late during the LDEF mission.

Peters, Palmer N.↗

NASA NTRS1991

LDEF attitude measurement using a pinhole camera with a silver/oxygen atom detector

A small device designed to measure the orbital attitude stability of the Long Duration Exposure Facility (LDEF) spacecraft is examined. The device used the reaction of Ag with O atoms, which convert the metal to a nonconducting black appearing oxide with high efficiency. The atmosphere at LDEF altitudes consists of more than 90 pct. atomic O. The device is a small hemispheric Ag surface facing a pinhole in a metal plate on the front surface of the satellite. It was expected that the stream of O atoms, travelling at a relatively velocity of 8 km/s would pass through the pinhole and strike the Ag surface at the geometric center, producing a circular black spot. In fact, the position of the spot has clearly shown that the LDEF was rotated by 8.0 + or - 0.4 deg from its nominal attitude, but that it was remarkably stable about this offset. The ellipticity of the recorded spot was attributed to a yaw oscillation of + or - 0.2 deg, however it was previously noted, that the co-rotation of the Earth's atmosphere should produce a sweeping of the atom beam vector of ca. + or - 1.5 deg about the surface normal. Such an effect was not visible in this experiment.

Gregory, John C.↗