Engineering topics

Gregorek, G. M.

Publications and source records attributed to Gregorek, G. M..

At least 19 records

NASA NTRS1995

Comparative wind tunnel test at high Reynolds numbers of NACA 64 621 airfoils with two aileron configurations

An experimental program to measure the aerodynamic characteristics of the NACA 64-621 airfoil when equipped with plain ailerons of 0.38 chord and 0.30 chord and with 0.38 chord balanced aileron has been conducted in the pressurized O.S.U. 6 x 12 ft High Reynolds Number Wind Tunnel. Surface pressures were measured and integrated to yield lift and pressure drag coefficients for angles of attack from -3 to +42 deg and for selected aileron deflections from 0 to -90 deg at nominal Mach and Reynolds numbers of 0.25 and 5 x 10(exp 6). When resolved into thrust coefficient for wind turbine aerodynamic control applications, the data indicated the anticipated decrease in thrust coefficient with negative aileron deflection at low angles of attack; however, as angle of attack increased, thrust coefficients eventually became positive. All aileron configurations, even at -90 deg deflections showed this trend. Hinge moments for each configuration complete the data set.

Gregorek, G. M.↗

NASA NTRS1992

Experimental unsteady pressures on an oscillating cascade with supersonic leading edge locus

The first experimental data for an oscillating cascade with a supersonic leading edge locus (SLEL) at zero stagger angle is presented which were obtained in the NASA/OSU supersonic oscillating cascade facility. Reduced frequencies from .093 to .146, based on half chord were investigated. An influence coefficient technique for a linear oscillating cascade with constant interblade phase angle has been extended to a cascade with a SLEL.

Erwin, Daniel↗

NASA NTRS1992

The design of four hypersonic reconnaissance aircraft

Four different hypersonic reconnaissance aircraft were designed by separate student teams. These aircraft were designed to provide the U.S. with a system to acquire aerial tactical reconnaissance when satellite reconnaissance proved unobtainable or ineffective. The design requirements given for this project stated that these aircraft must carry a 7500 lb, 250 cu ft payload of electronic and photographic intelligence gathering equipment over a target area at speeds between Mach 4-7 and at altitudes above 80,000 ft. Two of the aircraft were required to be manned by a crew of two and have a range of 12,000 nmi. One of these was to use airborne refueling to complete its mission while the other was not to use any refueling. The other two aircraft were required to be unmanned with a range of 6,000 nmi. One of these was to take off from another aircraft. The final details of all four aircraft designs along with an overview of the design process is provided.

Gregorek, G. M.↗

NASA NTRS1990

A hypersonic research vehicle to develop scramjet engines

Four student design teams produced conceptual designs for a research vehicle to develop the supersonic combustion ramjet (scramjet) engines necessary for efficient hypersonic flight. This research aircraft would provide flight test data for prototype scramjets that is not available in groundbased test facilities. The design specifications call for a research aircraft to be launched from a carrier aircraft at 40,000 feet and a Mach number of 0.8. The aircraft must accelerate to Mach 6 while climbing to a 100,000 foot altitude and then ignite the experimental scramjet engines for acceleration to Mach 10. The research vehicle must then be recovered for another flight. The students responded with four different designs, two piloted waverider configurations, and two unmanned vehicles, one with a blended body-wing configuration, the other with a delta wing shape. All aircraft made use of an engine database provided by the General Electric Aircraft Engine Group; both turbofan ramjet and scramjet engine performance using liquid hydrogen fuel was available. Explained here are the students' conceptual designs and the aerodynamic and propulsion concepts that made their designs feasible.

Gregorek, G. M.↗

NASA NTRS1988

Comparison of pressure distributions on model and full-scale NACA 64-621 airfoils with ailerons for wind turbine application

The aerodynamic similarity between a small (4-inch chord) wind tunnel model and a full-scale wind turbine blade (24-foot tip section with a 36-inch chord) was evaluated by comparing selected pressure distributions around the geometrically similar cross sections. The airfoils were NACA 64-621 sections, including trailing-edge ailerons with a width equal to 38 percent of the airfoil chord. The model airfoil was tested in the OSU 6- by 12-inch High Reynolds Number Wind Tunnel; the full-scale blade section was tested in the NASA Langley Research Center 30- by 60-foot Subsonic Wind Tunnel. The model airfoil contained 61 pressure taps connected by embedded tubes to pressure transducers. A belt containing 29 pressure taps was fixed to the full-scale section at midspan to obtain surface pressure data. Lift coefficients were obtained by integrating pressures, and corrections were made for the 3-D effects of blade twist and downwash in the blade tip section. The results of the two different experimental methods correlated well for angles of attack from minus 4 to 36 degrees and aileron reflections from 0 to 90 degrees.

Gregorek, G. M.↗

NASA NTRS1987

Wind tunnel evaluation of a truncated NACA 64-621 airfoil for wind turbine applications

An experimental program to measure the aerodynamic performance of a NACA 64-621 airfoil with a truncated trailing edge for wind turbine applications has been conducted in the Ohio State University Aeronautical and Astronautical Research Laboratory 6 in. by 21 in. pressurized wind tunnel. The blunted or trailing edge truncated (TET) airfoil has an advantage over similar trailing edge airfoils because it is able to streamline a larger spar structure, while also providing aerodynamic properties that are quite good. Surface pressures were measured and integrated to determine the lift, pressure drag, and moment coefficients over angles of attack ranging from -14 to +90 deg at Mach 0.2 and Reynolds numbers of 1,000,000 and 600,000. Results are compared to the NACA 0025, 0030, and 0035 thick airfoils with sharp trailing edges. Comparison shows that the 30 percent thick NACA 64-621-TET airfoil has higher maximum lift, higher lift curve slope, lower drag at higher lift coefficients, and higher chordwise force coefficient than similar thick airfoils with sharp trailing edges.

Law, S. P.↗

NASA NTRS1987

Two-dimensional aerodynamic characteristics of the AMES HI-120, HI-8, and LOW-12 airfoils

During the period between June and September 1986, the Aeronautical and Astronautical Engineering Research Laboratory (AARL) at the Ohio State University (OSU) in Columbus, Ohio, conducted tests in the 6"X22" Transonic Blowdown Wind Tunnel to determine the two-dimensional lift, drag, and pitching moment coefficients for three airfoils designated AMES HI-120, AMES LOW-12, and AMES HI-8. These tests covered a Mach number range of 0.20 to 0.86, Reynolds numbers between 2 x 10 to the 6th and 6 x 10 to the 6th powers, and angles of attack between 0 and 13 degs as directed by the NASA Project Engineer; each model was not run at every condition. This work was performed under NASA Grant NAG-2-401, Analysis of Two Advanced Transonic Airfoils.

Gregorek, G. M.↗

NASA NTRS1986

Airfoil aerodynamics in icing conditions

Methods of analyzing and experimentally measuring the effect of ice accretion on airfoil sections are presented. Empirical and analytical methods for predicting airfoil performance degradation due to ice are discussed. Ice simulation techniques for aerodynamic testing are presented and compared to data with actual ice accretions. The results show that simulation techniques to imitate the effect of ice on airfoil performance work well in most cases. Comparisons between predicted and measured airfoil performance with ice accretions are presented. For rime ice cases, the predictions compared well with experiments; but for glaze ice, a need for improved methods are seen.

Bragg, M. B.↗

NASA NTRS1984

Comparative wind tunnel tests at high Reynolds numbers of NACA 64 621 airfoils with two aileron configurations

An experimental program to measure the aerodynamic characteristics of the NACA 64-621 airfoil when equipped with plain ailerons of 0.38 chord and 0.30 chord and with 0.38 chord balanced aileron has been conducted in a pressurized 6 x 12-inch High Reynolds Number Wind Tunnel. Surface pressures were measured and integrated to yield lift and pressure drag coefficients for angles of attack from -3 deg to +42 deg, and for selected aileron deflections from 0 to -90 deg at nominal Mach and Reynolds numbers of 0.25 and 5 x l0 exp 6, respectively. When resolved into thrust coefficient for wind turbine aerodynamic control applications, the data indicated the anticipated decrease in thrust coefficient with negative aileron deflection at low angles of attack; however, as angle of attack increased, thrust coefficients eventually became positive. All aileron configurations, even at -90 deg deflections, showed this trend. Hinge moments for each configuration complete the data set.

Gregorek, G. M.↗

NASA NTRS1984

Results of an experimental program investigating the effects of simulated ice on the performance of the NACA 63A415 airfoil with flap

Aerodynamic data from a test program in the Icing Research Tunnel are reported for a NACA 63A415 airfoil, with fowler flap, clean and with simulated ice shapes. The effect of three ice shapes on airfoil performance are presented, two of the simulated ice shapes are from earlier Icing Tunnel tests. Lift, drag, and moment coefficients are reported for the airfoil, clean and with ice, for angles of attack from approximately zero lift to maximum lift and for flap deflections of 0, 10, 20, and 30 degrees. Surface pressure distribution plots for the airfoil and flap are presented for all runs. Some preliminary oil flow visualization data are also discussed. Large drag penalties were measured in all instances. Maximum lift penalties were in general serious, and depend upon the ice shape and flap deflection.

Zaguli, R. J.↗

NASA NTRS1984

Experimental and analytical investigations into airfoil icing

Methods of analyzing and measuring experimentally the accretion of ice and its effect on airfoil aerodynamic performance are presented. An analytical method for predicting water droplet impingement has been developed and shows the influence of airfoil leading edge radius and thickness on droplet impingement to be significant. Rime ice accretions are predicted including time dependent effects and these shapes compare well to experiment. Scaling water droplet impingement and rime ice accretion is discussed. Predictions of the effect of rime ice on airfoil performance are developed based on empirical and analytical methods. Techniques for measuring and simulating ice accretions for wind tunnel tests compare well to actual iced airfoil aerodynamic data. Data showing the effect of ice on measured airfoil performance using real and simulated ice are presented.

Bragg, M. B.↗

NASA NTRS1984

Performance of two transonic airfoil wind tunnels utilizing limited ventilation

A limited-zone ventilated wall panel was developed for a closed-wall icing tunnel which permitted correct simulation of transonic flow over model rotor airfoil sections with and without ice accretions. Candidate porous panels were tested in the Ohio State University 6- x 12-inch transonic airfoil tunnel and result in essentially interference-free flow, as evidenced by pressure distributions over a NACA 0012 airfoil for Mach numbers up to 0.75. Application to the NRC 12- x 12-inch icing tunnel showed a similar result, which allowed proper transonic flow simulation in that tunnel over its full speed range.

Lee, J. D.↗

NASA NTRS1984

Modeling techniques for transonic airfoils

In the present comparative study of computer codes for the modeling of two-dimensional, single element airfoil sections for various section geometry classes, two of the codes use vortex singularities methods to obtain the potential flow solution while the remainder solve the full inviscid potential flow equations by means of finite differencing techniques that allow results to be obtained for transonic flow about an airfoil which includes weak shocks. Computational results are presented for a symmetrical airfoil section, a conventional section, and a supercritical one. Icing condition applications of the models are noted. The model codes' range of applicability and agreement with each other and experimental results, as well as their computer run times and memory requirements, are noted.

Petrie, S. L.↗

NASA NTRS1983

Flight investigation of natural laminar flow on the Bellanca Skyrocket II

Two major concerns have inhibited the use of natural laminar flow (NLF) for viscous drag reduction on production aircraft. These are the concerns of achieveability of NLF on practical airframe surfaces, and maintainability in operating environments. Previous research in this area left a mixture of positive and negative conclusions regarding these concerns. While early (pre-1950) airframe construction methods could not achieve NLF criteria for waviness, several modern construction methods (composites for example) can achieve the required smoothness. This paper presents flight experiment data on the achieveability and maintainability of NLF on a high-performance, single-propeller, composite airplane, the Bellanca Skyrocket II. The significant contribution of laminar flow to the performance of this airplane was measured. Observations of laminar flow in the propeller slipstream are discussed, as are the effects of insect contamination on the wing. These observations have resulted in a new appreciation of the operational feasibility for achieving and maintaining NLF on modern airframe surfaces.

Holmes, B. J.↗

NASA NTRS1983

An analytical evaluation of the icing properties of several low and medium speed airfoils

A droplet trajectory computer code is used to analyze the water droplet impingement characteristics of several low and medium speed airfoils. The results are reported in terms of the airfoil maximum impingement efficiency, and limits of impingement. The airfoils are analyzed for angles of attack of -4 to 12 degrees, and modified inertia parameters of 0.01 to 1.0. These data are then used to evaluate the effect of airfoil geometry: leading edge radius, maximum thickness, maximum camber, and angle of attack on airfoil icing characteristics. Airfoils from the NACA four digit series to the new NASA NLF airfoils are considered. The strongest correlations were seen between airfoil leading edge radius and maximum local collection efficiency, thickness and total collection efficiency, and camber and the limits of impingement.

Bragg, M. B.↗

NASA NTRS1982

Wind tunnel evaluation of air-foil performance using simulated ice shapes

A two-phase wind tunnel test was conducted in the 6 by 9 foot Icing Research Tunnel (IRT) at NASA Lewis Research Center to evaluate the effect of ice on the performance of a full scale general aviation wing. In the first IRT tests, rime and glaze shapes were carefully documented as functions of angle of attack and free stream conditions. Next, simulated ice shapes were constructed for two rime and two glaze shapes and used in the second IRT tunnel entry. The ice shapes and the clean airfoil were tapped to obtain surface pressures and a probe used to measure the wake characteristics. These data were recorded and processed, on-line, with a minicomputer/digital data acquisition system. The effect of both rime and glaze ice on the pressure distribution, Cl, Cd, and Cm are presented.

Bragg, M. B.↗

NASA NTRS1982

An investigation of the aerodynamic characteristics of a new general aviation airfoil in flight

A low speed airfoil, the GA(W)-2, - a 13% thickness to chord ratio airfoil was evaluated. The wing of a Beech Sundowner was modified at by adding balsa ribs and covered with aluminum skin, to alter the existing airfoil shape to that of the GA(W)-2 airfoil. The aircraft was flown in a flight test program that gathered wing surface pressures and wake data from which the lift drag, and pitching moment of the airfoil could be determined. After the base line performance of the airfoil was measured, the drag due to surface irregularities such as steps, rivets and surface waviness was determined. The potential reduction of drag through the use of surface coatings such as KAPTON was also investigated.

Gregorek, G. M.↗

NASA NTRS1982

Aerodynamic characteristics of airfoils with ice accretions

Results of a wind tunnel test to evaluate the performance of an airfoil with simulated rime ice are presented with theoretical comparisons. A NACA 65A413 airfoil was tested in the OSU 6 x 22 inch Transonic Airfoil Wind Tunnel at a Reynolds number near three million and Mach numbers from 0.20 to 0.80. The model was tested in four configurations to determine the aero-dynamic effects of the roughness and shape of a rime ice accretion. The simulated rime ice shape was obtained analytically using a time-stepping dry ice accretion computer code. Lift, drag, moment coefficients, and pressure distributions for the clean and simulated rime ice cases are reported. The measured degradation in airfoil performance is compared to an analytical method which uses existing airfoil analysis computer codes with empirical corrections for the surface roughness. A discussion of the empirical surface roughness correction and uses of other airfoil computer methods is included.

Bragg, M. B.↗