Engineering Papers⌕ Search

Engineering topics

Green, M. J.

Publications and source records attributed to Green, M. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Numerical simulation of hypersonic, axisymmetric flowfields

Flow conditions corresponding to those of three previously conducted hypersonic axisymmetric flow experiments are presently treated by numerical solutions of the axisymmetric, thin layer Navier-Stokes equations with the Chemistry and Gasdynamic Implicit computer code's Version 2. While simulation and experimental results agree for ideal gas flows, the simulation for the case of a real gas flow reveals that the particular coupling of the gasdynamics and the chemistry used in the code degrades the convergence level obtainable, by comparison with ideal gas cases. The computed stagnation point heating is 60 percent lower than for the experiment.

Green, M. J.↗
NASA NTRS1985

Radiative viscous-shock-layer analysis of Fire, Apollo, and PAET flight data

Equilibrium, radiating viscous-shock-layer solutions are obtained for a number of trajectory points of the Fire II, Apollo 4, and PAET experimental flight vehicles. Convective heating rates calculated by a benchmark code agree well, except at high altitudes corresponding to low densities, with two engineering correlations. Calculated radiation intensities are compared with the flight radiometer data and with inviscid flow results. Differences as great as 70 percent are observed between measured data and the viscous calculations. Viscous effects reduce the intensity toward the wall, because of boundary-layer absorption, by as much as 30 percent, compared with inviscid intensities. Preliminary chemical and thermal nonequilibrium flow calculations along a stagnation streamline for a PAET trajectory predict enhancement of radiation owing to chemical relaxation. Stagnation point solutions are also presented for future air-assisted orbital transfer vehicle geometries with nose radii ranging from 0.3 to 15 m.

Balakrishnan, A.↗
NASA NTRS1985

CAG12 - A CSCM based procedure for flow of an equilibrium chemically reacting gas

The Conservative Supra Characteristic Method (CSCM), an implicit upwind Navier-Stokes algorithm, is extended to the numerical simulation of flows in chemical equilibrium. The resulting computer code known as Chemistry and Gasdynamics Implicit - Version 2 (CAG12) is described. First-order accurate results are presented for inviscid and viscous Mach 20 flows of air past a hemisphere-cylinder. The solution procedure captures the bow shock in a chemically reacting gas, a technique that is needed for simulating high altitude, rarefied flows. In an initial effort to validate the code, the inviscid results are compared with published gasdynamic and chemistry solutions and satisfactorily agreement is obtained.

Green, M. J.↗
NASA NTRS1985

Aerothermodynamic environment for a Titan probe with deployable decelerator

It is pointed out that further exploration of Titan, Saturn's largest moon, is of current interest to the scientific community, particularly from the standpoint of the organic chemical evolution of its atmosphere. For a suitable study of this Saturnian satellite, a mission involving a Titan atmospheric entry probe is to be conducted. The probe is to employ a deployable decelerator with the aim to allow scientific measurements in the haze layer. The present investigation is concerned with an assessment of the aerothermodynamic environment for the considered probe during its hypervelocity, low-Reynolds-number entry. Attention is given to the employed computational method, the Titan probe configuration, the Titan probe trajectory, the viscous-layer regime of the aerothermodynamic environment, and the incipient merged-layer regime.

Green, M. J.↗
NASA NTRS1984

Aerothermodynamic environment and thermal protection for a Titan aerocapture vehicle

This paper presents thermal protection system (TPS) requirements for a potential Titan aerocapture vehicle. Shock-layer solutions are obtained for a nominal trajectory through the current Titan model atmosphere. Fully laminar and fully turbulent solutions are presented along the blunted fore-cone in the windward symmetry plane of a bent-biconic vehicle. Using these solutions to define the aerothermodynamic environment, transient material-response solutions are obtained for a Galileo-type TPS with a carbon-phenolic ablator heat shield. Shock-layer results indicate that turbulent flow is the more realistic flow condition. They also show that the lengthy aerocapture heating pulse is dominated by convective heating. The TPS results show that the required insulation thickness is uniformly about 4 cm along the fore-cone because of the long heat-soak period. The total heat-shield thickness is 6.4 cm at the stagnation point, and 4.7 cm near the end of the fore-cone. These TPS requirements are greater than those presented in a previous Titan aerocapture study.

Green, M. J.↗
NASA NTRS1983

Supporting flight data analysis for Space Shuttle Orbiter Experiments at NASA Ames Research Center

The Space Shuttle Orbiter Experiments program in responsible for collecting flight data to extend the research and technology base for future aerospace vehicle design. The Infrared Imagery of Shuttle (IRIS), Catalytic Surface Effects, and Tile Gap Heating experiments sponsored by Ames Research Center are part of this program. The paper describes the software required to process the flight data which support these experiments. In addition, data analysis techniques, developed in support of the IRIS experiment, are discussed. Using the flight data base, the techniques have provided information useful in analyzing and correcting problems with the experiment, and in interpreting the IRIS image obtained during the entry of the third Shuttle mission.

Green, M. J.↗
NASA NTRS1983

Ablation of carbonaceous materials in a hydrogen-helium arc-jet flow

The stagnation-point ablation rates of a graphite, a carbon-carbon composite, and four carbon-phenolic materials are measured in an arc-jet wind tunnel with a 50 percent hydrogen-50 percent helium mixture as the test gas. Flow environments are determined through measurements of static and impact pressures, heat-transfer rates to a calorimeter, and radiation spectra, and through numerical calculation of the flow through the wind tunnel, spectra, and heat-transfer rates. The environments so determined are: impact pressure approximately equal to 3 atm, Mach number approximately equal to 2.1, convective heat-transfer rate approximately equal to 14 kW/sq cm, and radiative heat-transfer rate approximately equal to 7 kW/sq cm in the absence of ablation. Ablation rates are determined from the measured rates of mass loss and recession of the ablation specimens. Compared with the predicted ablation rates obtained by running RASLE and CMA codes, the measured rates are higher by about 15 percent for all tested materials.

Park, C.↗
NASA NTRS1983

Supporting flight data analysis for Space Shuttle Orbiter experiments at NASA Ames Research Center

The space shuttle orbiter experiments program is responsible for collecting flight data to extend the research and technology base for future aerospace vehicle design. The infrared imagery of shuttle (IRIS), catalytic surface effects, and tile gap heating experiments sponsored by Ames Research Center are part of this program. The software required to process the flight data which support these experiments is described. In addition, data analysis techniques, developed in support of the IRIS experiment, are discussed. Using the flight data base, the techniques provide information useful in analyzing and correcting problems with the experiment, and in interpreting the IRIS image obtained during the entry of the third shuttle mission.

Green, M. J.↗
NASA NTRS1983

Ablation of carbonaceous materials in a hydrogen-helium arc-jet flow

The stagnation-point ablation rates of a graphite, a carbon-carbon composite, and four carbon-phenolic materials are measured in an arc-jet wind tunnel with a 50% hydrogen-50% helium mixture as the test gas. Flow environments are determined through measurements of static and impact pressures, heat-transfer rates to a calorimeter, and radiation spectra, and through numerical calculation of the flow through the wind tunnel, spectra, and heat-transfer rates. The environments so determined are: impact pressure approx. 3 atm, Mach number approx. 2.1, convective heat-transfer rate approx. 14 kw/sq cm, and radiative heat-transfer rate approx. 7 kw/sq cm in the absence of ablation. Ablation rates are determined from the measured rates of mass loss and recession of the ablation specimens. Compared with the predicted ablation rates obtained by running RASLE and CMA codes, the measured rates are higher by about 15% for all tested materials.

Park, C.↗
NASA NTRS1981

Galileo Probe forebody thermal protection

Material response solutions for the forebody heat shield on the candidate 310-kg Galileo Probe are presented. A charring material ablation analysis predicts thermochemical surface recession, insulation thickness, and total required heat shield mass. Benchmark shock layer solutions provide the imposed entry heating environments on the ablating surface. Heat shield sizing results are given for a nominal entry into modeled nominal and cool-heavy Jovian atmospheres, and for two heat-shield property models. The nominally designed heat shield requires a mass of at least 126 kg and would require an additional 13 kg to survive entry into the less probable cool-heavy atmosphere. The material-property model with a 30% surface reflectance reduces these mass requirements by as much as 16%.

Green, M. J.↗
NASA NTRS1981

Forebody and base region real gas flow in severe planetary entry by a factored implicit numerical method. II - Equilibrium reactive gas

The factored-implicit, gas-dynamic algorithm has been adapted to the numerical simulation of equilibrium reactive flows. Changes required in the perfect gas version of the algorithm are developed, and the method of coupling gas-dynamic and chemistry variables is discussed. A flow-field solution that approximates a Jovian entry case was obtained by this method and compared with the same solution obtained by HYVIS, a computer program much used for the study of planetary entry. Comparison of surface pressure distribution and stagnation line shock-layer profiles indicates that the two solutions agree well.

Davy, W. C.↗
NASA NTRS1980

Forebody and base region real-gas flow in severe planetary entry by a factored implicit numerical method. I - Computational fluid dynamics

A new code for the simulation of full (forebody and base region) flowfields about bluff bodies in the hypersonic regime of severe planetary entry is described. The present 'maximally conservative, maximally differenced' formulation of the unsteady compressible Navier-Stokes equations for 2-D axisymmetric 3-D flow is contrasted for stability with previous formulations of Viviand, Kutler, et al, and Thomas and Lombard. Discrete metric relations peculiar to the axisymmetric finite volume formulation are presented along with a general discussion of their relations to and consequences of failure to close computational cells. A computational mesh of curvilinear coordinate topology singular in the flow regime is presented that permits aligned capturing of the major physical features of the complex flowfield.

Lombard, C. K.↗
NASA NTRS1979

Numerical simulation of experiments in the Giant Planet Facility

Utilizing a series of existing computer codes, ablation experiments in the Giant Planet Facility are numerically simulated. Of primary importance is the simulation of the low Mach number shock layer that envelops the test model. The RASLE shock-layer code, used in the Jupiter entry probe heat-shield design, is adapted to the experimental conditions. RASLE predictions for radiative and convective heat fluxes are in good agreement with calorimeter measurements. In simulating carbonaceous ablation experiments, the RASLE code is coupled directly with the CMA material response code. For the graphite models, predicted and measured recessions agree very well. Predicted recession for the carbon phenolic models is 50% higher than that measured. This is the first time codes used for the Jupiter probe design have been compared with experiments.

Green, M. J.↗
NASA NTRS1978

Aerothermodynamic environment for Jovian entry with silica heat shield

Solutions are presented for the stagnation-region shock-layer equations, including radiative transfer with spectral lines and silica ablation during Jovian entry. Results for variations of entry angle, sphere-cone configuration, and atmospheric model are given. The effect of silica ablation on the radiative and convective surface heating is correlated with the ratio of the wall to free-stream mass flux. Correlations are also given for spectral distributions. The effect of newly obtained SiO radiation properties on the surface heating is examined.

Green, M. J.↗
NASA NTRS1973

Thermal shielding by subliming volume reflectors in convective and intense radiative environments.

The behavior of dielectric materials having densely packed internal scattering centers subject to extreme convective and radiative environments is analyzed. Experiments have shown that these materials act as volume reflectors of incident radiation even when the exposed surface is being eroded by thermochemical ablation. The analysis was applied to interpret experiments of subliming Teflon models exposed to combined radiative and convective fluxes up to 1.7 kW/sq cm for several seconds. Results show that, although the exposed surface receded at an apparently steady rate, the internal temperature climbed continually, due to internal absorption of radiation and would have caused failure internally if the test duration were extended a few seconds. Thus, performance is time-limited by the internal absorption coefficient. Results were obtained for larger configurations and other materials. Typically, Teflon shells may withstand radiant fluxes up to 20 kW/sq cm for about 5 sec and fritted quartz up to 50 kW/sq cm for about 8 sec (corresponding to the Jupiter entry).

Howe, J. T.↗
NASA NTRS1973

Analysis of sublimation-cooled coated mirrors in convective and radiative environments.

Analytical solutions were obtained for the thermal response of a transpiration- or sublimation-cooled spherical mirror coating exposed to convective and radiative heating. The solutions allow unlimited spectral detail to be accounted for. Results indicate that transpiration-cooled thick coatings (1 cm) may withstand up to 10 kW/sq cm on a steady basis without excessive temperature rise for quartzlike materials with an internal absorption coefficient of 0.01 per cm. On a transient basis, fluxes up to 20 kW/sq cm can be accommodated for a second (cW laser exposure time), 4 kW/sq cm for 5 sec (planetary entry heating time), and of the order of MW/sq cm for millisecond times (short-duration laser bursts) without transpiration cooling for a material with an absorption coefficient of 0.1 per cm. Proportionately higher fluxes can be accommodated with lower absorption coefficients. Thermal stresses produced by the heat pulse are found to be high but within the strength of the materials. The regime in which meaningful solutions may be obtained is mapped in detail.

Howe, J. T.↗
NASA NTRS1972

Numerical method for the solution of large systems of differential equations of the boundary layer type

A numerical method for the solution of large systems of nonlinear differential equations of the boundary-layer type is described. The method is a modification of the technique for satisfying asymptotic boundary conditions. The present method employs inverse interpolation instead of the Newton method to adjust the initial conditions of the related initial-value problem. This eliminates the so-called perturbation equations. The elimination of the perturbation equations not only reduces the user's preliminary work in the application of the method, but also reduces the number of time-consuming initial-value problems to be numerically solved at each iteration. For further ease of application, the solution of the overdetermined system for the unknown initial conditions is obtained automatically by applying Golub's linear least-squares algorithm. The relative ease of application of the proposed numerical method increases directly as the order of the differential-equation system increases. Hence, the method is especially attractive for the solution of large-order systems. After the method is described, it is applied to a fifth-order problem from boundary-layer theory.

Green, M. J.↗