Engineering topics

Greber, I.

Publications and source records attributed to Greber, I..

At least 19 records

NASA NTRS1988

Glancing shock wave-turbulent boundary layer interaction with boundary layer suction

Tests conducted to ascertain the stagnation pressure and flow angularity profiles of a turbulent boundary layer subjected to boundary layer suction (BLS) as it crosses a glancing sidewall shock wave have determined that the boundary layer does not separate upon crossing the shock wave. Without BLS, the upstream influence of the shock wave-induced wall static pressure rise was extensive, of the order of four bloundary layer thicknesses; for the same case, with suction, the extent of upstream influence was 50 percent lower. In addition, flow angularities at the wall were found to be smaller with suction than without it.

Barnhart, P. J.↗

NASA NTRS1984

Dilution jets in accelerated cross flows

Results of flow visualization experiments and measurements of the temperature field produced by a single jet and a row of dilution jets issued into a reverse flow combustor are presented. The flow in such combustors is typified by transverse and longitudinal acceleration during the passage through its bending section. The flow visualization experiments are designed to examine the separate effects of longitudinal and transverse acceleration on the jet trajectory and spreading rate. A model describing a dense single jet in a lighter accelerating cross flow is developed. The model is based on integral conservation equations, including the pressure terms appropriate to accelerating flows. It uses a modified entrainment correlation obtained from previous experiments of a jet in a cross stream. The flow visualization results are compared with the model calculations in terms of trajectories and spreading rates. Each experiment is typified by a set of three parameters: momentum ratio, density ratio and the densimetric Froude number.

Lipshitz, A.↗

NASA NTRS1984

An analytical model for the vorticity associated with a transverse jet

A two dimensional model is developed for a turbulent jet injected normally into a uniform crossflow, in which particular emphasis is placed on the contra-rotating vortex pair associated with the jet. By approximating the forces acting on each of the viscous vortices, equations governing the vortex spacing and downstream jet velocity are evolved. No empirical information is incorporated into this model. A description of the variation in total vortex strength is utilized in which vorticity generated by the jet's impulse dominates the farfield. Numerical solution of the governing equations yields results for the vortex trajectory, half spacing, varying circulation, and viscous core size that correlate quite well with experimental data and asymptotic relations. Based on these findings, we conclude that vortex separation and other important characteristics of the jet cross-section are two dimensional and viscous in nature. Hence it becomes possible to predict, on purely theoretical grounds, the behavior of the vortex pair and of the jet itself.

Karagozian, A. R.↗

NASA NTRS1984

Dilution jet experiments in compact combustor configurations

This project concerns the effects of cooling jets on the velocity and temperature fields in a compact reverse flow combustor. The work is motivated by the need to limit the temperatures of post combustion gases in jet engines to values within the endurance capabilities of turbine blades. The application requires not only that the temperature be kept sufficiently low but also that a suitably tailored temperature profile be provided at the combustor exit, with higher temperatures generally permissible at the blade tip than at the blade root because of higher centrifugal loads at the root. Flows in reverse flow combustor accelerate both longitudinally because of area changes and transversely because of flow turning. The current project started with flow visualization experiments in water, using aqueous solutions of zinc bromide to model the relatively higher density of cooling jets.

Greber, I.↗

NASA NTRS1984

Experimental studies on two dimensional shock boundary layer interactions

Experiments have been performed on the interaction of oblique shock waves with flat plate boundary layers in the 30.48 cm x 30.48 cm (1 ft. x 1 ft.) supersonic wind tunnel at NASA Lewis Research Center. High accuracy measurements of the plate surface static pressure and shear stress distributions as well as boundary layer velocity profiles were obtained through the interaction region. Documentation was also performed of the tunnel test section flow field and of the two-dimensionality of the interaction regions. The findings provide detailed description of two-dimensional interaction with initially laminar boundary layers over the Mach number range 2.0 to 4.0. Additional information with regard to interactions involving initially transitional boundary layers is presented over the Mach number range 2.0 to 3.0 and those for initially turbulent boundary layers at Mach 2.0. These experiments were directed toward providing well documented information of high accuracy useful as test cases for analytic and numerical calculations. Flow conditions encompassed a Reynolds number range of 4.72E6 to 2.95E7 per meter. The shock boundary layer interaction results were found to be generally in good agreement with the experimental work of previous authors both in terms of direct numerical comparison and in support of correlations establishing laminar separation characteristics.

Skebe, S. A.↗

NASA NTRS1983

Dilution Jet Experiments in Compact Combustor Configurations

The effects of cooling jets on the velocity and temperature fields in a compact reverse flow combustion are discussed. The work is motivated by the need to limit the temperature of past-combustion gases in jet engines to values within the endurance capabilities of turbine blades. The application requires not only that the temperature be kept sufficiently low but also that a suitably tailored temperature profile be provided at the combustor exit, with higher temperatures generally permissible at the blade tip than at the blade root because of higher centrifugal loads at the root. A single jet. As spacing is reduced, jet penetration is also reduced, and the cooling jets tend to remain close to the wall from which they are injected. Results suggest that cooling and temperature distribution tailoring can be accomplished without injecting cooling jets upstream of the turn, and thus it appears that combustors can be made smaller than current designs.

Greber, I.↗

NASA NTRS1982

Dilution Jet Behavior in the Turn Section of a Reverse Flow Combuster

Measurements of the temperature field produced by a single jet and a row of dilution jets issued into a reverse flow combustor are presented. The temperature measurements are presented in the form of consecutive normalized temperature profiles, and jet trajectories. Single jet trajectories were swept toward the inner wall of the turn, whether injection was from the inner or outer wall. This behavior is explained by the radially inward velocity component necessary to support irrotational flow through the turn. Comparison between experimental results and model calculations showed poor agreement due to the model's not including the radial velocity component. A widely spaced row of jets produced trajectories similar to single jets at similar test conditions, but as spacing ratio was reduced, penetration was reduced to the point where the dilution jet flow attached to the wall.

Riddlebaugh, S. M.↗

NASA NTRS1982

Dilution jet behavior in the turn section of a reverse flow combustor

Riddlebaugh, S. M.↗

NASA NTRS1981

Turbulent jet patterns in accelerating flows

Results of flow visualization experiments, and a semi-empirical model of a single turbulent jet injected perpendicularly to a different density cross flow are presented. The model is based on integral conservation equations, including the pressure terms appropriate to accelerating flow. It uses an entrainment correlation obtained from previous experiments of a jet in a cross stream. The results show trajectories and spreading rates, and are typified by a set of three parameters: momentum ratio, Froude number and density ratio. Agreement between test and calculated results is encouraging, but tend to be poorer with increasing momentum ratio.

Lipshitz, A.↗

NASA NTRS1974

Experiments on confined turbulent jets in cross flow

Results are reported of experiments on the effects of an opposite wall on the characteristics of turbulent jets injected into a cross flow, for unheated and heated jets. Longitudinal and transverse distributions of velocity and temperature are presented for single and multiple circular jets, and trajectories are presented for two-dimensional jets. The opposite wall has relatively little effect on a single jet unless the ratio of jet to cross flow momentum flux is large enough for the jet to impinge on the opposite wall. For a row of jets aligned perpendicularly to the cross flow, the opposite wall exerts progressively larger influence as the spacing between jets decreases. Much of the effect of jet and wall proximity can be understood by considering the interaction of the vortex flow which is the major feature of the structure of a single jet in a cross flow. Smoke photographs are shown to elucidate some of the interaction patterns.

Kamotani, Y.↗

NASA NTRS1973

Experiments on confined turbulent jets in cross flow.

Results are reported of experiments on the effects of an opposite wall on the characteristics of turbulent jets injected into a cross flow, for unheated and heated jets. Longitudinal and transverse distributions of velocity and temperature are presented for single and multiple circular jets, and trajectories are presented for two-domensional jets. The opposite wall has relatively little effect on a single jet unless the ratio of jet to cross flow momentum flux is large enough for the jet to impinge on the opposite wall. For a row of jets aligned perpendicularly to the cross flow, the opposite wall exerts progressively larger influence as the spacing between jets decreases. Much of the effect of jet and wall proximity can be understood by considering the interaction of the vortex flow which is the major feature of the structure of a single jet in a cross flow. Smoke photographs are shown to elucidate some of the interaction patterns.

Kamotani, Y.↗

NASA NTRS1972

Investigations of a turbulent jet in a crossflow

Analyses of flow field downstream of jet directed at right angles into crossflow for heated and unheated single jets are presented. Application of flow data to cooling system for gas turbine combustion chambers is discussed. Temperature distribution, velocity trajectory, and vortex motion are described.

Kamotani, Y.↗

NASA NTRS1972

Experiments on a turbulent jet in a cross flow.

Results are reported of experiments on turbulent circular jets issuing into a cross flow, both for unheated and heated jets. Longitudinal and transverse distributions of velocity, temperature, and turbulence intensity are presented. The velocity distributions depend mainly on the ratio of jet to cross flow momentum flux. The temperature distributions depend also on the density ratio. The jet structure is dominated by a vortex wake which forms behind the jet, which is evident both from the detail measurements and from smoke photographs of the flow. The experiments also indicate that the components of cross flow normal and parallel to the jet trajectory independently control the entrainment rate.

Kamotani, Y.↗

NASA NTRS1971

New half-range differential approximation for spherically-symmetric radiative transfer.

A new half-range differential approximation for radiative transfer with spherical symmetry is presented. The development is motivated by the various failures of existing differential approximations in determining emissive-power distributions and heat transfer for concentric-spheres problems. The new approach represents a modification of the four-moment double spherical-harmonics method, to which it reduces in the planar limit. The difference is effected by relocating the discontinuity of the assumed directional distribution of radiation intensity. The shift takes the discontinuity from precisely on the division between radially inward and radially outward, to just within the radially-outward directional half range. The method is tested on a variety of concentric spheres problems with and without internal heat sources, reproducing all the important features of the exact results.

Moreno, J. B.↗

NASA NTRS1971