Low temperature epitaxial growth of Ge on Ca F2 buffered cube-textured Ni
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Goyal, Amit.
Explore the source record for details and available documents.
CdTe thin film has been grown by metalorganic chemical vapor deposition (MOCVD) on Ni(100) substrate. Using x-ray pole figure measurements we observed the epitaxial relationship of {111}CdTe// {001}Ni with [110]CdTe//[010]Ni and [112] CdTe//[100]Ni. The 12 diffraction peaks in the (111) pole figure of CdTe film and their relative positions with respect to the four peak positions in the (111) pole figure of Ni substrate are consistent with four equivalent orientational domains of CdTe with three to four superlattice match of about 0.7% in the [110] direction of CdTe and the [010] direction of Ni. The electron backscattered diffraction (EBSD) images show that the CdTe domains are 30 degrees orientated from each other.
The critical current density Jc and the magnetic relaxation ( creep ) properties have been studied for a set of NdBa2Cu3O7- (NdBCO) films doped with BaZrO3 (BZO) nanoparticles to form columnar defects. The dependence of Jc on the magnitude and orientation of the applied magnetic field Happ (0 6.5 T); and temperature T (5 K Tc) was investigated. The normalized flux-creep rate S = d ln(J ) / d ln(t) was determined as a function of T. The current dependence of the effective activation energy Ueff(J) was derived using the formalism developed by Maley. The results are well described by an inverse power-law type barrier of the form 0 0 ( ) ~ ( / ) eff U J U J J with fitted values for the pinning energy scale U0 and the glassy exponent . When comparing values for these parameters in the BZO-doped samples with those for their undoped control counterparts, the most striking difference is the larger scale of current density J0 in the doped samples (a factor of 2.4 higher), while the other pinning parameters do not differ strongly. In the BZO-doped materials, the pinning energy scale U0 increases with vortex density and J0 decreases, with both following simple power law dependencies on field.
We report on a low-cost, innovative approach for synthesizing prepatterned, magnetic nanostructures, the shapes and dimensions of which can be easily tuned to meet requirements for next-generation data storage technology. The magnetic nanostructures consist of self-assembled Co nanodots and nanowires embedded in yttria-stabilized zirconia (YSZ) matrices. The controllable size and aspect ratio of the nanostructures allows the selection of morphologies ranging from nanodots to nanowires. Co nanowires show strong shape anisotropy and large remanence at 300 K. In contrast, Co nanodots display minimal effects of magnetocrystalline anisotropy and superparamagnetic relaxation above the blocking temperature. These prepatterned magnetic nanostructures are very promising candidates for data storage technology with an ultrahigh density of 1 terabit in{sup -2} or higher.
Phase stability of cubic-pyrochlore-structured RE3TaO7 (RTO, where RE = rare earth elements) pinning additives in YBa2Cu3O7- (YBCO) superconductor and the pinning properties influenced by RTO addition into YBCO films were investigated. RTO completely reacts with YBCO and is converted to cubic-double-perovskite-structured Ba2RETaO6 (BRETO), a more thermodynamically stable tantalate phase within YBCO. In RTO-doped YBCO films, BRETO self-assembled nanocolumnns align along the c-axis of the film and play a major role in the improvement of flux pinning and Jc performance over wide magnetic field and angular ranges.
We demonstrate that the competing cubic-quintic nonlinearity induces propagating solitonlike dark(bright) solitons and double-kink solitons in the nonlinear Schroedinger equation with self-steepening and self-frequency shift. Parameter domains are delineated in which these optical solitons exist. Also, fractional-transform solitons are explored for this model. It is shown that the nonlinear chirp associated with each of these optical pulses is directly proportional to the intensity of the wave and saturates at some finite value as the retarded time approaches its asymptotic value. We further show that the amplitude of the chirping can be controlled by varying the self-steepening term and self-frequency shift.
The growth of graphene has been carried out on cube-textured (100) oriented Cu (CTO-Cu) foils using chemical vapor deposition (CVD). Well-aligned triangular grains self-assembled on CTO-Cu during CVD heating in flowing hydrogen. The nucleation of triangular graphene grains has been confirmed. This demonstrates that the shape and possible alignment of the graphene grains can potentially be tuned by changing the properties of the substrate, which should ultimately lead to improved electrical properties of the graphene. This type of graphene nucleation and alignment is novel and has not been observed in previous studies on other copper foil samples.
Novel articles and methods to fabricate same with self-assembled nanodots and/or nanorods of a single or multicomponent material within another single or multicomponent material for use in electrical, electronic, magnetic, electromagnetic, superconducting and electrooptical devices is disclosed. Self-assembled nanodots and/or nanorods are ordered arrays wherein ordering occurs due to strain minimization during growth of the materials. A simple method to accomplish this when depositing in-situ films is also disclosed. Device applications of resulting materials are in areas of superconductivity, photovoltaics, ferroelectrics, magnetoresistance, high density storage, solid state lighting, non-volatile memory, photoluminescence, thermoelectrics and in quantum dot lasers.
The present invention relates to a method for producing a defect-containing superconducting film, the method comprising (a) depositing a phase-separable layer epitaxially onto a biaxially-textured substrate, wherein the phase-separable layer includes at least two phase-separable components; (b) achieving nanoscale phase separation of the phase-separable layer such that a phase-separated layer including at least two phase-separated components is produced; and (c) depositing a superconducting film epitaxially onto said phase-separated components of the phase-separated layer such that nanoscale features of the phase-separated layer are propagated into the superconducting film.
Novel articles and methods to fabricate the same resulting in flexible, large-area, triaxially textured, single-crystal or single-crystal-like, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.
A warm-rolled, annealed, polycrystalline, cube-textured, {100}<100>, FCC-based alloy substrate is characterized by a yield strength greater than 200 MPa and a biaxial texture characterized by a FWHM of less than 15.degree. in all directions.
Grain boundaries (GBs) in high-temperature superconductors suppress the critical current density (Jc) dramatically [1-3]. The Jc drops exponentially when GB-misorientation exceeds 4 [3]. To reduce the number of high-angle GBs, fabrication of biaxially-textured, superconducting wires via epitaxial growth on cube-textured metals has been widely investigated [4-6]. Such wires have exhibited very high-Jc in applied magnetic fields despite having a majority of GBs with total misorientations greater than 4 . Here we show that GB networks in these wires have numerous GBs with out-of-plane misorientations > 4 and few boundaries having in-plane misorientations > 4 . The high performance can be explained if the Jc is determined primarily by in-plane misorientations. This supposition was confirmed by in-field transport measurements on artificially fabricated bicrystals of superconductors having only out-of-plane misorientations. Atomic resolution imaging of bicrystals with out-of-plane misorientations show that superconducting ab-planes are continuous across such GBs in contrast to GBs with in-plane misorientations.
Technological applications of high temperature superconductors (HTS) require high critical current density, Jc, under operation at high magnetic field strengths. This requires effective flux pinning by introducing artificial defects through creative processing. In this work, we generated correlated disorder for strong vortex pinning in the YBa2Cu3O7- (YBCO) films by replacing the standard LaMnO3 (LMO) cap buffer layers in ion beam assisted deposited MgO templates with LMO:MgO composite films. Such films revealed formation of two phase-separated, but at the same time vertically aligned, self-assembled composite nanostructures that extend throughout the entire thickness of the film. Measurements of magnetic-field orientation-dependent Jc of YBCO coatings deposited on these nanostructured cap layers showed correlated c-axis pinning and improved in-field Jc performance compared to those of YBCO films deposited on standard LMO buffers. The present results demonstrate feasibility of novel and potentially practical approaches in the pursuit of more efficient, economical, and high performance superconducting devices.
(111)-, (101)-, and (001)-oriented polycrystalline BiFeO3 films were fabricated on rolling-assisted biaxially textured substrates (RABiTS) with appropriate, buffer layer engineering of heteroepitaxially grown buffer multilayers on RABiTS. The crystallographic orientation and polarization direction were confirmed using X-ray diffraction and piezoresponse force microscopy (PFM), respectively. All the films exhibited excellent ferroelectric properties. Switching spectroscopy PFM demonstrated that the switching polarization in (111)-oriented polycrystalline BiFeO3 films is higher than (101) or (001) oriented films. These high-quality, BiFeO3 films on low-cost, flexible, biaxially textured metallic tapes with controllable orientation and polarization are attractive for application in flexible ferroelectric devices.
A laminated conductor includes a metallic substrate having a surface, a biaxially textured buffer layer supported by the surface of the substrate, the biaxially textured buffer layer comprising LZO and a dopant for mitigating metal diffusion through the LZO, and a biaxially textured conductor layer supported by the biaxially textured buffer layer.
Lanthanum Zirconium Oxide, La2Zr2O7 (LZO) has been developed as a potential replacement barrier layer in the standard RABiTS three-layer architecture of physical vapor deposited CeO2 cap/YSZ barrier/Y2O3 seed/Ni-5W. The main focus of this research is to see (i) whether we can improve further the barrier properties of LZO; (ii) can we widen the LZO composition and still achieve the high performance?; and (iii) is it possible to reduce the number of buffer layers? We report a systematic investigation of the LZO film growth with varying compositions of La:Zr ratio in the La2O3-ZrO2 system. Using metal-organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of LaxZr1-xOy (x = 0.2-0.6) on standard Y2O3 buffered Ni-5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial LZO phase without the (111) texture can be achieved in a wider compositional window of x = 0.2-0.6 in LaxZr1-xOy. Both CeO2 cap layers and MOD-YBCO films were grown 2 epitaxially on these modified LZO barriers. Transport property measurements indicate that we can achieve a higher critical current, Ic of 274-292 A/cm at 77 K and self-field on MOD-YBCO films grown on LaxZr1-xOy (x = 0.4-0.6) films. These results indicate that LZO films can be grown with a wider compositional window and still achieve high performance YBCO coated conductors. In addition, epitaxial MOD LaxZr1-xOy (x = 0.25) films were grown directly on biaxially textured Ni-3W substrates. About 3 m thick YBCO films with a Jc of 0.55 MA/cm2 at 77 K and 0.01 T were grown on a single MOD LZO buffered Ni-3W substrate using pulsed laser deposition. This work promises a route for producing simplified buffer architecture for RABiTS based YBCO coated conductors.