Engineering topics

Goradia, C.

Publications and source records attributed to Goradia, C..

27 records · Page 2

NASA NTRS1981

A theory of the n-i-p silicon solar cell

A computer model has been developed, based on an analytical theory of the high base resistivity BSF n(+)(pi)p(+) or p(+)(nu)n(+) silicon solar cell. The model makes very few assumptions and accounts for nonuniform optical generation, generation and recombination in the junction space charge region, and bandgap narrowing in the heavily doped regions. The paper presents calculated results based on this model and compares them to available experimental data. Also discussed is radiation damage in high base resistivity n(+)(pi)p(+) space solar cells.

Goradia, C.↗

NASA NTRS1980

Planar multijunction high voltage solar cells

Technical considerations, preliminary results, and fabrication details are discussed for a family of high-voltage planar multi-junction (PMJ) solar cells which combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

Evans, J. C., Jr.↗

NASA NTRS1980

The planar multijunction cell - A new solar cell for earth and space

A new family of high-voltage solar cells, called the planar multijunction (PMJ) cell is being developed. The new cells combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell area. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

Evans, J. C., Jr.↗

NASA NTRS1980

Theoretical results on the double-collecting tandem junction solar cell

Results of computer calculations using a one dimensional model of the silicon tandem junction solar cell with both front and back current collection are presented. Using realistically achievable geometrical and material parameters, the model predicts that with base widths of 50 micrometers and 100 micrometers and base resistivities between 1 ohm/cm and 20 ohm/cm, beginning of life efficiencies of 14% to 17% and end of life efficiencies of 12% to 14%, after about seven years in synchronous orbit, can be obtained.

Goradia, C.↗

NASA NTRS1980

Radiation damage in silicon NIP solar cells

The performance parameters of n(+) p p(+) silicon solar cells of varying thicknesses with boron doped p base resistivities of 1250 and 84 ohm centimeters were determined. High injection theory was used to analyze the experimental data. Results from an analysis of open circuit voltages show a much greater contribution to V(oc) from the back junction than is the case for the lower resistivity in common use. The base minority carrier distribution is seen to be significant in determining the contribution of V(B), the base contribution to V(oc). Although V(B) is small, its value increases with increasing radiation fluence. In this connection it is noted that, with illumination from the p(+) side, the sign of V(B) becomes positive, and V(B) itself becomes an additive term to V(oc). Diffusion lengths determined under high injection conditions are significantly greater than those obtained under low injection, while damage coefficients under low injection are higher than those obtained under high injection conditions.

Weinberg, I.↗

NASA NTRS1980

Theoretical results on the tandem junction solar cell based on its Ebers-Moll transistor model

A one-dimensional theoretical model of the tandem junction solar cell (TJC) with base resistivity greater than about 1 ohm-cm and under low level injection has been derived. This model extends a previously published conceptual model which treats the TJC as an npn transistor. The model gives theoretical expressions for each of the Ebers-Moll type currents of the illuminated TJC and allows for the calculation of the spectral response, I(sc), V(oc), FF and eta under variation of one or more of the geometrical and material parameters and 1MeV electron fluence. Results of computer calculations based on this model are presented and discussed. These results indicate that for space applications, both a high beginning of life efficiency, greater than 15% AM0, and a high radiation tolerance can be achieved only with thin (less than 50 microns) TJC's with high base resistivity (greater than 10 ohm-cm).

Goradia, C.↗

NASA NTRS1977

A first order theory of the p/+/-n-n/+/ edge-illuminated silicon solar cell at very high injection levels

A first order theory of the edge-illuminated p(+)-n-n(+) silicon solar cell under very high injection levels has been derived. The very high injection level illuminated J-V characteristic is derived for any general base width to diffusion length (W/L) ratio and it includes the minority carrier reflection by the n-n(+) high-low junction. The beneficial effects of the high-low junction are shown to be significant until extremely high injection levels are reached. The theoretical dependencies of Jsc and Voc on temperature, incident intensity, and base resistivity are derived and discussed in detail. Some experimental results are given and these are discussed in relation to the theory.

Goradia, C.↗

NASA NTRS1975

The high intensity solar cell - Key to low cost photovoltaic power

This paper discusses the problems associated with conventional solar cells at high intensities and presents the design considerations and performance characteristics of the 'high intensity' (HI) solar cell which appears to eliminate the major problems. Test data obtained at greater than 250 AM1 suns gave a peak output power density of 2 W per sq cm at an efficiency exceeding 6% with an unoptimized cell operating at over 100 C. It appears that operation at 1000 AM1 suns at efficiencies greater than 10% is possible. At 1000 AM1 suns and 10% efficiency, the HI cell manufacturing cost is estimated to be $0.25/watt, with multi-megawatt annual production capability already existing within the industrial sector. A high intensity solar system was also analyzed to determine its cost effectiveness and to assess the benefits of further improving HI cell efficiency.

Sater, B. L.↗

NASA NTRS1975

The high intensity solar cell: Key to low cost photovoltaic power

The design considerations and performance characteristics of the 'high intensity' (HI) solar cell are presented. A high intensity solar system was analyzed to determine its cost effectiveness and to assess the benefits of further improving HI cell efficiency. It is shown that residential sized systems can be produced at less than $1000/kW peak electric power. Due to their superior high intensity performance characteristics compared to the conventional and VMJ cells, HI cells and light concentrators may be the key to low cost photovoltaic power.

Sater, B. L.↗