Engineering topics

Goodman, Wesley L.

Publications and source records attributed to Goodman, Wesley L..

6 records

NASA NTRS2012

A Practical Methodology for Quantifying Random and Systematic Components of Unexplained Variance in a Wind Tunnel

This paper documents a check standard wind tunnel test conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3M TCT) that was designed and analyzed using the Modern Design of Experiments (MDOE). The test designed to partition the unexplained variance of typical wind tunnel data samples into two constituent components, one attributable to ordinary random error, and one attributable to systematic error induced by covariate effects. Covariate effects in wind tunnel testing are discussed, with examples. The impact of systematic (non-random) unexplained variance on the statistical independence of sequential measurements is reviewed. The corresponding correlation among experimental errors is discussed, as is the impact of such correlation on experimental results generally. The specific experiment documented herein was organized as a formal test for the presence of unexplained variance in representative samples of wind tunnel data, in order to quantify the frequency with which such systematic error was detected, and its magnitude relative to ordinary random error. Levels of systematic and random error reported here are representative of those quantified in other facilities, as cited in the references.

Deloach, Richard↗

NASA NTRS2000

Development of a Large Field of View Shadowgraph System for a 16 Ft. Transonic Wind Tunnel

A large field of view shadowgraph flow visualization system for the Langley 16 ft. Transonic Tunnel (16 ft.TT) has been developed to provide fast, low cost, aerodynamic design concept evaluation capability to support the development of the next generation of commercial and military aircraft and space launch vehicles. Key features of the 16 ft. TT shadowgraph system are: (1) high resolution (1280 X 1024) digital snap shots and sequences; (2) video recording of shadowgraph at 30 frames per second; (3) pan, tilt, & zoom to find and observe flow features; (4) one microsecond flash for freeze frame images; (5) large field of view approximately 12 X 6 ft; and (6) a low maintenance, high signal/noise ratio, retro-reflective screen to allow shadowgraph imaging while test section lights are on.

Talley, Michael A.↗

NASA NTRS1991

Multi-element airfoil optimization for maximum lift at high Reynolds numbers

An experimental study has been performed to assess the maximum lift capability of a supercritical multielement airfoil representative of an advanced transport aircraft wing. The airfoil model was designed with a leading-edge slat and single or two-segment trailing-edge flaps. Optimization work was performed at various slat/flap deflections as well as gap/overhang positions. Landing configurations and the attainment of maximum lift coefficients of 4.5 with single-element flaps and 5.0 with two-segment flaps was emphasized. Test results showed a relatively linear variation of the optimum gap/overhang positioning of the slat versus slat deflection, considerable differences in optimum rigging between single and double segment flaps, and large Reynolds number effects on multielement airfoil optimization.

Valarezo, Walter O.↗

NASA NTRS1988

Passive control plate for shock-boundary layer interactions

Computational and experimental results are presented for a passive method capable of reducing or completely eliminating the separation region in shock-boundary layer interactions of the type that can result in severe performance degradation due to flow separation in supersonic and hypersonic inlets. The method involves the placement of an embedded plate in the outer portion of the boundary layer, parallel to the wall, so that the incident shock will impinge upon, and be reflected from, its surface. This will lower the pressure gradient in the low-momentum, near-wall region. A porous control plate's effect has also been investigated.

Goodman, Wesley L.↗

NASA NTRS1987

Drag reduction on a bluff body at yaw angles to 30 degrees

The base separation alleviation and drag reduction effectiveness of transverse rectangular grooves and longitudinal v-grooves in the afterbody shoulder region of a bluff body is investigated for body yaw angles of 0-30 deg. The grooves are found to be beneficial in reducing both freestream and axial drag coefficients at yaw angles of up to 25 deg.

Howard, Floyd G.↗

NASA NTRS1986

Wall turbulence control

A variety of wall turbulence control devices which were experimentally investigated are discussed; these include devices for burst control, alteration of outer flow structures, large eddy substitution, increased heat transfer efficiency, and reduction of wall pressure fluctuations. Control of pre-burst flow was demonstrated with a single, traveling surface depression which is phase-locked to elements of the burst production process. Another approach to wall turbulence control is to interfere with the outer layer coherent structures. A device in the outer part of a boundary layer was shown to suppress turbulence and reduce drag by opposing both the mean and unsteady vorticity in the boundary layer. Large eddy substitution is a method in which streamline curvature is introduced into the boundary layer in the form of streamwise vortices. Riblets, which were already shown to reduce turbulent drag, were also shown to exhibit superior heat transfer characteristics. Heat transfer efficiency as measured by the Reynolds Analogy Factor was shown to be as much as 36 percent greater than a smooth flat plate in a turbulent boundary layer. Large Eddy Break-Up (LEBU) which are also known to reduce turbulent drag were shown to reduce turbulent wall pressure fluctuation.

Wilkinson, Stephen P.↗