Engineering topics

Gooder, S. T.

Publications and source records attributed to Gooder, S. T..

9 records

NASA NTRS1989

Structural and thermal response of 30 cm diameter ion thruster optics

Tabular and graphical data are presented which are intended for use in calibrating and validating structural and thermal models of ion thruster optics. A 30 cm diameter, two electrode, mercury ion thruster was operated using two different electrode assembly designs. With no beam extraction, the transient and steady state temperature profiles and center electrode gaps were measured for three discharge powers. The data showed that the electrode mount design had little effect on the temperatures, but significantly impacted the motion of the electrode center. Equilibrium electrode gaps increased with one design and decreased with the other. Equilibrium displacements in excess of 0.5 mm and gap changes of 0.08 mm were measured at 450 W discharge power. Variations in equilibrium gaps were also found among assemblies of the same design. The presented data illustrate the necessity for high fidelity ion optics models and development of experimental techniques to allow their validation.

Macrae, G. S.↗

NASA NTRS1986

Pseudolog Digital-to-Analog Converter

Sensitivity decreases by 10 at beginning of each input decade. Method conceived to convert binary-coded data to suitable linear form for stripchart recording. Strip-chart recordings obtained from typical pressure readings in a vacuum system during pumpdown. In reading curve, BCD digital vacuum-gage output processed by analog-to-digital converter in such way that only reading digits (but not range) appear in output. In range and reading, range also converted to analog and placed as most significant digit.

Gooder, S. T.↗

NASA NTRS1984

Electromagnetic propulsion test facility

A test facility for the exploration of electromagnetic propulsion concept is described. The facility is designed to accommodate electromagnetic rail accelerators of various lengths (1 to 10 meters) and to provide accelerating energies of up to 240 kiloJoules. This accelerating energy is supplied as a current pulse of hundreds of kiloAmps lasting as long as 1 millisecond. The design, installation, and operating characteristics of the pulsed energy system are discussed. The test chamber and its operation at pressures down to 1300 Pascals (10 mm of mercury) are described. Some aspects of safety (interlocking, personnel protection, and operating procedures) are included.

Gooder, S. T.↗

NASA NTRS1977

Operational compatibility of 30-centimeter-diameter ion thruster with integrally regulated solar array power source

System tests were performed in which Integrally Regulated Solar Arrays (IRSA's) were used to directly power the beam and accelerator loads of a 30-cm-diameter, electron bombardment, mercury ion thruster. The remaining thruster loads were supplied from conventional power-processing circuits. This combination of IRSA's and conventional circuits formed a hybrid power processor. Thruster performance was evaluated at 3/4- and 1-A beam currents with both the IRSA-hybrid and conventional power processors and was found to be identical for both systems. Power processing is significantly more efficient with the hybrid system. System dynamics and IRSA response to thruster arcs are also examined.

Gooder, S. T.↗

NASA NTRS1976

Series-parallel method of direct solar array regulation

A 40 watt experimental solar array was directly regulated by shorting out appropriate combinations of series and parallel segments of a solar array. Regulation switches were employed to control the array at various set-point voltages between 25 and 40 volts. Regulation to within + or - 0.5 volt was obtained over a range of solar array temperatures and illumination levels as an active load was varied from open circuit to maximum available power. A fourfold reduction in regulation switch power dissipation was achieved with series-parallel regulation as compared to the usual series-only switching for direct solar array regulation.

Gooder, S. T.↗

NASA NTRS1976

Laboratory 15 kV high voltage solar array facility

The laboratory high voltage solar array facility is a photoelectric power generating system. Consisting of nine modules with over 23,000 solar cells, the facility is capable of delivering more than a kilowatt of power. The physical and electrical characteristics of the facility are described.

Kolecki, J. C.↗

NASA NTRS1975

Design and development of a 5 kV isolated solid state switch

A unique microcircuit intended for use as a shorting switch for large extraterrestrial solar cell arrays is described. The packaging design for the 5 kV isolated hybrid switch is different from most hybrid microcircuits in that it utilizes a compartmentalized plastic case (a portion of which is encapsulated), is not hermetic, and is designed for high voltage operation.

Holbrook, R. J.↗

NASA NTRS1975

Design and development of a 5 kV isolated solid state switch

This paper describes the design and fabrication of a 5000 volt isolated hybrid switch developed by Hughes Aircraft Company under contract to NASA/Lewis. Hughes did the packaging design and NASA did the circuit design. This unique microcircuit is intended for use as a shorting switch for large extraterrestrial solar cell arrays. The packaging design for the 5 kV isolated hybrid switch is different from most hybrid microcircuits in that it utilizes a compartmentalized plastic case (a portion of which is encapsulated), is not hermetic, and is designed for high voltage operation.

Holbrook, R. J.↗

NASA NTRS1974

Self-protecting solid state isolated switch

Solid state switch has following capabilities: (1) Hybrid or IC from compatible with direct mounting on solar array substrate; (2) Continuous signal is not required to hold it in either on or off state; (3) Separate signal lines for on and off control; (4) Electrically isolated from input signals; and (5) Current surges will not cause switch failure.

Hoffman, A. C.↗