Engineering PapersSearch

Engineering topics

Gonzalez, R.

Publications and source records attributed to Gonzalez, R..

Orion Entry Handling Qualities Assessments

The Orion Command Module (CM) is a capsule designed to bring crew back from the International Space Station (ISS), the moon and beyond. The atmospheric entry portion of the flight is deigned to be flown in autopilot mode for nominal situations. However, there exists the possibility for the crew to take over manual control in off-nominal situations. In these instances, the spacecraft must meet specific handling qualities criteria. To address these criteria two separate assessments of the Orion CM s entry Handling Qualities (HQ) were conducted at NASA s Johnson Space Center (JSC) using the Cooper-Harper scale (Cooper & Harper, 1969). These assessments were conducted in the summers of 2008 and 2010 using the Advanced NASA Technology Architecture for Exploration Studies (ANTARES) six degree of freedom, high fidelity Guidance, Navigation, and Control (GN&C) simulation. This paper will address the specifics of the handling qualities criteria, the vehicle configuration, the scenarios flown, the simulation background and setup, crew interfaces and displays, piloting techniques, ratings and crew comments, pre- and post-fight briefings, lessons learned and changes made to improve the overall system performance. The data collection tools, methods, data reduction and output reports will also be discussed. The objective of the 2008 entry HQ assessment was to evaluate the handling qualities of the CM during a lunar skip return. A lunar skip entry case was selected because it was considered the most demanding of all bank control scenarios. Even though skip entry is not planned to be flown manually, it was hypothesized that if a pilot could fly the harder skip entry case, then they could also fly a simpler loads managed or ballistic (constant bank rate command) entry scenario. In addition, with the evaluation set-up of multiple tasks within the entry case, handling qualities ratings collected in the evaluation could be used to assess other scenarios such as the constant bank angle maintenance case. The 2008 entry assessment was divided into two sections (see Figure 1). Entry I was the first, high speed portion of a lunar return and Entry II was the second, lower speed portion of a lunar return, which is similar (but not identical) to a typical ISS return.

Bihari, B.

Evaluation of Thermoregulation After Spaceflight

Altered thermoregulation has been reported following spaceflight simulations such as water immersion and bedrest but it has never been evaluated immediately after actual spaceflight. Impaired thermoregulation may have significant impact during various spaceflight activities such as countermeasure exercise, extravehicular activity (EVA), landing, and egress. It would be manifested as an increased body temperature and heart rate and decreased work capacity and endurance. In this study we evaluated the exercise responses of two crewmembers following a long duration spaceflight and measured their changes in body temperatures, skin blood flow, sweating and heat production during a mild submaximal exercise stress.

Schneider, S. M.

Temperature Regulation in Crewmembers After a 115-Day Space Flight

Impaired thermoregulation, which has been observed during exercise following bed rest, may significantly impact crewmembers during space flight operations by decreasing exercise capacity and orthostatic tolerance. Impaired temperature regulation would cause higher levels of core temperature, due to an attenuated cutaneous vasodilatory reflex and sweating response, for a given oxygen consumption. Two mate crewmembers of the Mir 18 mission performed supine cycle exercise se (20 min @ 40% and 20 min @ 65% preflight VO2pk) 145 days preflight and 5 days postflight. Core temperature (Tcore) was measured by an ingestible telemetry pill, skin blood flow (SBF) by laser Doppler velocimetry, and sweat rate (SR) by dew point hygrometry. Tcore at the time of test termination was similar (37.8 C) for both subjects before and after flight despite a shorter test duration (40 vs 28-29 minutes) postflight. The slopes of the SBF/Tcore relationship (Subj 1: 396 vs 214; Subj 2: 704 vs 143 Perfusion Unit/degC) and SR/Tcore relationship (Subj 1: 4.5 vs 2.1; Subj 2: 11.0 vs 3.6mg/min/sq cm/degC) were reduced postflight. Tcore thresholds for both SR (Subj 1: 37.4 vs 37.6; Subj 2: 37.6 vs 37.6 C) and SBF (Subj 1: 37.3 vs 37.5; Subj 2: 37.6 vs 37.7 C) were similar pre- to postflight. For these 2 crewmembers, it appeared that thermoregulation during exercise was impaired as evidenced by compromised heat loss responses after long-duration space flight.

Lee, S. M. C.

Cascading process in the flute-mode turbulence of a plasma

The cascades of ideal invariants in the flute-mode turbulence are analyzed by considering a statistics based on an elementary three-mode coupling process. The statistical dynamics of the system is investigated on the basis of the existence of the physically most important (PMI) triad. When finite ion Larmor radius effects are considered, the PMI triad describes the formation of zonal flows.

Gonzalez, R.

Lightweight Motorized Valve

Redesigned actuator assembly weighs 50 percent less. Isolator valve operated by ac motor instead of usual dc solenoid. Valve weighs only 3 lb (1.4 kg). New valve functions with either two-phase or three-phase power. Developed for isolating fluids in propellant tanks, manifolds, and interconnecting lines of Space Shuttle reaction control and orbital maneuvering subsystems, valve suited to applications in which leakage must be kept to minimum at high pressure differences - in petroleum and chemical processing.

Gonzalez, R.

Ditigal-Image Enhancement

Programable system enhances digitally monocular and stereographic images at video rates. Provides automatic and interactive enhancement modes based on histogram modification and intensity-mapping techniques.

Woods, R.

Improved Cure-in-Place Silicone Adhesives

Two improved cure-in-place silicone-elastomer-based adhesives have low thermal expansion and low thermal conductivity. Adhesives are flexible at low temperature and withstand high temperatures without disintegrating. New ablative compounds were initially developed for in-flight repair of insulating tile on Space Shuttle orbiter. Could find use in other applications requiring high-performance adhesives, such as sealants for solar collectors.

Blevins, C. E.

Self-aligning, low-pressure sealing poppet valve

Design and characteristics of poppet valve operated by very low differential pressures to control fluid flow are described. Valve is used to control flow of petroleum, chemical, and aircraft hydraulics where low leakage rates and activation at low pressures are required.

Gonzalez, R.

Leaching of nitroso rubber material removes uncured polymer

New leaching process removes uncured polymer from nitroso rubber, elastomer used in presence of nitrogen tetroxide. Uncured portion is removed by controlled soaking of polymer slab in Freon TF. Leaching with Freon TF prevents nitroso rubber from adhering to adjoining surfaces and limiting its usefulness in either static or dynamic applications.

Bratfisch, W. A.