Engineering Papers⌕ Search

Engineering topics

Goglia, G. L.

Publications and source records attributed to Goglia, G. L..

31 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Experimental study of flow due to an isolated suction hole and a partially plugged suction slot

Details for construction of a model of a partially plugged, laminar flow control, suction slot and an isolated hole are presented. The experimental wind tunnel facility and instrumentation is described. Preliminary boundary layer velocity profiles (without suction model) are presented and shown to be in good agreement with the Blasius laminar profile. Recommendations for the completion of the study are made. An experimental program for study of transition on a rotating disk is described along with preliminary disturbance amplification rate data.

Goglia, G. L.↗
NASA NTRS1979

Synthesis of a control model for a liquid nitrogen cooled, closed circuit, cryogenic nitrogen wind tunnel and its validation

The details of the efforts to synthesize a control-compatible multivariable model of a liquid nitrogen cooled, gaseous nitrogen operated, closed circuit, cryogenic pressure tunnel are presented. The synthesized model was transformed into a real-time cryogenic tunnel simulator, and this model is validated by comparing the model responses to the actual tunnel responses of the 0.3 m transonic cryogenic tunnel, using the quasi-steady-state and the transient responses of the model and the tunnel. The global nature of the simple, explicit, lumped multivariable model of a closed circuit cryogenic tunnel is demonstrated.

Balakrishna, S.↗
NASA NTRS1979

Measurements of flow phenomena induced by suction through perforated and partially plugged surfaces

Efforts were directed towards completing construction of the windtunnel test section, assembling instrumentation, programming the data acquisition and reduction system, adjusting the streamwise pressure gradient of the test section, calibrating the hot-wire anemometer probe, and constructing and testing a smoke generator. The test section was installed in the wind tunnel and is completely operational. The streamwise pressure gradient was adjusted to be nominally zero at a free-stream velocity of 3.05 m/s (10 ft/s). This was accomplished by adjusting the upper wall of the test section to be slightly divergent. The change in static pressure between any two streamwise locations in the test section was less than one percent of the free-stream dynamic pressure. A suitable means was found for accurately calibrating the hot-wire probe which is used to measure boundary-layer velocity profiles and fluctuating velocities.

Wilkinson, S. P.↗
NASA NTRS1978

Development of a three-dimensional Navier-Stokes code on CDC star-100 computer

A three-dimensional code in body-fitted coordinates was developed using MacCormack's algorithm. The code is structured to be compatible with any general configuration, provided that the metric coefficients for the transformation are available. The governing equations are developed in primitive variables in order to facilitate the incorporation of physical boundary conditions and turbulence-closure models. MacCormack's two-step, unsplit, time-marching algorithm is used to solve the unsteady Navier-Stokes equations until steady-state solution is achieved. Cases discussed include (1) flat plate in supersonic free stream; (2) supersonic flow along an axial corner; (3) subsonic flow in an axial corner at M infinity = 0.95; and (4) supersonic flow in an axial corner at M infinity 1.5.

Vatsa, V. N.↗
NASA NTRS1978

Analytical and numerical investigation of structural response of compliant wall materials

Theoretical analysis of an electrostatically driven wall system for a compliant wall drag reduction program is reported. The electrostatic wall system is capable of producing deflections of many orders greater than the thicknesses and at small wavelengths. An intermediate large response theory was used for structural analysis. The theoretical predictions were compared to bench test results, and good agreement between the two was obtained. The effects of aerodynamic loads and perturbation electric fields on the theoretical solutions were considered. It was shown that for very small wavelengths (approximately 2mm) the aerodynamic effects can be estimated using potential theory without loss of accuracy, and the perturbation electric fields do not affect solutions as long as the deflections are less than one percent of the wavelength. Resonance effects for this type of structure were shown to be fairly small.

Goglia, G. L.↗
NASA NTRS1977

Computations in turbulent flows and off-design performance predictions for airframe-integrated scramjets

The research activity focused on two main tasks: (1) the further development of the SCRAM program and, in particular, the addition of a procedure for modeling the mechanism of the internal adjustment process of the flow, in response to the imposed thermal load across the combustor and (2) the development of a numerical code for the computation of the variation of concentrations throughout a turbulent field, where finite-rate reactions occur. The code also includes an estimation of the effect of the phenomenon called 'unmixedness'.

Goglia, G. L.↗
NASA NTRS1977

Modal identification of structures from the responses and random decrement signatures

The theory and application of a method which utilizes the free response of a structure to determine its vibration parameters is described. The time-domain free response is digitized and used in a digital computer program to determine the number of modes excited, the natural frequencies, the damping factors, and the modal vectors. The technique is applied to a complex generalized payload model previously tested using sine sweep method and analyzed by NASTRAN. Ten modes of the payload model are identified. In case free decay response is not readily available, an algorithm is developed to obtain the free responses of a structure from its random responses, due to some unknown or known random input or inputs, using the random decrement technique without changing time correlation between signals. The algorithm is tested using random responses from a generalized payload model and from the space shuttle model.

Brahim, S. R.↗
NASA NTRS1977

Dynamic characteristics of rotor blades with pendulum absorbers

The point transmission matrix for a vertical plane pendulum on a rotating blade undergoing combined flapwise bending, and chordwise bending and torsion is derived. The equilibrium equation of the pendulum is linearized for small oscillations about the steady state. A FORTRAN program was written for the case of a vertical plane pendulum attached to a uniform blade with flapwise bending degree of freedom for cantilever boundary conditions. The frequency has a singular value right at the uncoupled pendulum natural frequency and thus introduces two frequencies corresponding to the nearest natural frequency of the blade without pendulum. In both of these modes it was observed that the pendulum deflection is large. One frequency can be thought of as a coupled pendulum frequency and the other as a coupled bending and pendulum frequency.

Murthy, V. R.↗
NASA NTRS1977

Analytical and numerical investigation of structural response of compliant wall materials

Surface motion of compliant walls in drag reduction experiments was analyzed. The spectrum of surface motion indicates that membranes over deep cavities respond at low frequencies and large wavelengths. The membrane over a deep cavity is therefore found not to yield the desired reponse predicted by the postulated mechanism. The membrane over a thin air gap is found to act as a wavelength chopper, and analysis of the nonlinear response of the compliant surface indicates its possible suitability for compliant wall experiments. Periodic structures are found to lock in the desired wavelengths of motion. Laminated structures are found to be very ineffective as compliant models, except when there is no bonding between the membrane and the backing. Computer programs developed for these analyses are documented.

Goglia, G. L.↗
NASA NTRS1976

Addition of higher order plate and shell elements into NASTRAN computer program

Two higher order plate elements, the linear strain triangular membrane element and the quintic bending element, along with a shallow shell element, suitable for inclusion into the NASTRAN (NASA Structural Analysis) program are described. Additions to the NASTRAN Theoretical Manual, Users' Manual, Programmers' Manual and the NASTRAN Demonstration Problem Manual, for inclusion of these elements into the NASTRAN program are also presented.

Narayanaswami, R.↗
NASA NTRS1976

A numerical study of flow phenomena within a vortex sink rate sensor

A numerical investigation of a viscous incompressible fluid with constant properties within a vortex sink rate sensor is undertaken. A computer program was developed, for obtaining the numerical solution of the Navier-Stokes equations, assuming laminar flow, having general prescribed inlet conditions and axisymmetric boundary conditions. Computational results for various viscous flows and assorted boundary conditions have been obtained. In the vortex chamber, the radial momentum is conserved, whereas the axial momentum is negligible. In the sink region, the radial and tangential velocities, as well as the tangential vorticities, have significantly high values. In the sink tube, the radial momentum is negligible. The radial momentum within the vortex chamber is converted to the axial momentum in the sink tube. A change in the flow rate had an appreciable effect within the sensor and particularly near the sink tube entrance. As the flow rate was increased, both the tangential velocity and tangential vorticity increased rapidly. At the higher flow rates, vortices were produced at the corner of the entrance section of the sink tube.

Patel, D. K.↗
NASA NTRS1974

An experimental and theoretical study of the flow phenomena within a vortex sink rate sensor

Tests were conducted to obtain a description of the flow field within a vortex sink rate sensor and to observe the influence of viscous effects on its performance. The characteristics of the sensor are described. The method for conducting the test is reported. It was determined that for a specific mass flow rate and the geometry of the vortex chamber, the flow in the vortex chamber was only affected, locally, by the size of the sink tube diameter. Within the sink tube, all three velocity components were found to be higher for the small sink tube diameters. As the speed of rotation of the sensor was increased, the tangential velocities within the vortex chamber, as well as in the sink tube, increased in proportion to the speed of rotation.

Goglia, G. L.↗