Engineering Papers⌕ Search

Engineering topics

Glover, K. E.

Publications and source records attributed to Glover, K. E..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Development of spin resistance criteria for light general aviation airplanes

A brief history of stall/spin technology for light general aviation airplanes is presented. Criteria needed to describe desirable characteristics of a spin-resistant airplane and means to evaluate airplanes for compliance with the criteria have been developed. Initial results from limited flight tests of an experimental high-wing airplane indicated that the basic configuration would not meet the spin resistance criteria. Further tests with the airplane modified to enhance its spin resistance are planned.

Dicarlo, D. J.↗
NASA NTRS1985

Leading-edge design for improved spin resistance of wings incorporating conventional and advanced airfoils

Discontinuous wing leading-edge droop designs have been evaluated as a means of modifying wing autorotative characteristics and thus improving airplane spin resistance. Addition of a discontinuous outboard wing leading-edge droop to three typical light airplanes having NACA 6-series wing sections produced significant improvements in stall characteristics and spin resistance. Wind tunnel tests of two wings having advanced natural laminar flow airfoil sections indicated that a discontinuous leading-edge droop can delay the onset of autorotation at high angles of attack without adversely affecting the development of laminar flow at cruise angles of attack.

Stough, H. P., III↗
NASA NTRS1984

Use of a discontinuous wing leading-edge modification to enhance spin resistance for general aviation airplanes

Spin resistance of two typical general aviation airplanes has been studied. Improvement in spin resistance due to an outboard wing leading-edge modification was evaluated through wind-tunnel and flight tests. The basic airplanes would readily enter a spin; however, with the wing modification the airplanes were highly spin resistant. Spin resistance has been related to the angle of attack of the outer wing panel and the yaw rate as a step toward development of guidelines for design of more spin resistant airplanes.

Dicarlo, D. J.↗
NASA NTRS1984

Wing design for spin resistance

Use of a discontinuous outboard wing leading edge to improve stall/spin characteristics has been evaluated through wind-tunnel and flight tests. Addition of such a discontinuous outboard wing leading-edge droop design to three light airplanes having NACA 6-series airfoil sections produced significant improvements in stall characteristics and spin resistance. The increased spin resistance of the modified airplanes has been related to the difference in angle of attack between the outer wing panel stall and the maximum attainable angle of attack.

Stough, H. P., III↗
NASA NTRS1979

Some results from the use of a control augmentation system to study the developed spin of a light plane

A control augmentation system consisting of hydrogen peroxide rockets mounted on the wing tips of a light airplane has been developed and used to study spin recovery characteristics. Recovery from spins that were unrecoverable with aerodynamic controls was accomplished in less than one turn at maximum thrust in about three turns at minimum thrust. The rocket system at maximum thrust produced spin recovery characteristics similar to those obtained using a parachute. An advantage of using the control augmentation system on any airplane being used in a spin test program is its capability to demonstrate configuration effects on stall/spin characteristics at very high angles of attack and clearly determine the existence of all possible spin modes.

Obryan, T. C.↗
NASA NTRS1976

Development of a large support surface for an air-bearing type zero-gravity simulator

The methods used in producing a large, flat surface to serve as the supporting surface for an air-bearing type zero-gravity simulator using low clearance, thrust-pad type air bearings are described. Major problems encountered in the use of self-leveled epoxy coatings in this surface are discussed and techniques are recommended which proved effective in overcoming these problems. Performance requirements of the zero-gravity simulator vehicle which were pertinent to the specification of the air-bearing support surface are also discussed.

Glover, K. E.↗
NASA NTRS1975

The foot-controlled maneuvering unit: Summary report on Skylab experiment T-020

Skylab experiment T-020 was conducted to study the maneuvering capabilities of astronauts using a relatively simple experimental self-locomotive device, referred to as the foot-controlled maneuvering unit, and to evaluate the effectiveness of ground-based facilities simulating the operation of this device in weightless conditions of space. The final results as presented of this experiment which includes comparison of the tests performed during missions SL-3 and SL-4 of the Skylab with those performed on the simulators. Some of the results of this experiment and those of Skylab experiment M509, which employed an experimental hard-controlled maneuvering unit, are discussed in terms of the development of a possible future operational maneuvering system.

Hewes, D. E.↗
NASA NTRS1975

Premission and postmission simulation studies of the foot-controlled maneuvering unit for Skylab experiment T-020

A Skylab experiment was conducted to study the maneuvering capabilities of astronauts using a relatively simple self-locomotive device, referred to as the foot-controlled maneuvering unit, and to evaluate the effectiveness of ground-based facilities simulating the operation of this device in weightless conditions of space. Some of the special considerations given in the definition and development of the experiment as related to the two ground-based simulators are reviewed. These simulators were used to train the test subjects and to obtain baseline data which could be used for comparison with the in-flight tests that were performed inside the Skylab orbital workshop. The results of both premission and postmission tests are discussed, and subjective comparisons of the in-flight and ground-based test conditions are presented.

Hewes, D. E.↗
NASA NTRS1972

Development of Skylab experiment T020 employing a foot controlled maneuvering unit

A review of the plans and preparations is presented for Skylab experiment T020, entitled Foot-Controlled Maneuvering Unit (FCMU). The FCMU is an experimental system intended to explore the use of simple astronaut maneuvering devices in the zero-gravity environment of space. This review also includes discussions of the FCMU concept and experiment hardware systems, as well as supporting experiment definition and development research studies conducted with the aid of zero-gravity simulators.

Hewes, D. E.↗