Engineering Papers⌕ Search

Engineering topics

Glassman, A. J.

Publications and source records attributed to Glassman, A. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Three-Dimensional Turbomachine-Blade-Row Analysis Code

Computer program (MERNEW3D) developed that prepares bulk of input data set required for Denton three-dimensional inviscid turbomachine-blade-row analysis code. Denton input generated from minimum of geometry and flow-variable information by using cubic spline curve fits for interpolation and extrapolation. Curve-fitting procedures taken from previously developed and widely used NASA computer program (MERIDL), which performs meridional streamsurface analysis.

Glassman, A. J.↗
NASA NTRS1986

Off-Design Performance of Radial-Inflow Turbines

Computer code determines rotor exit flow from hub to tip. RTOD (Radial Turbine Off-Design), computes off-design performance of radial turbine by modeling flow with stator viscous and trailing-edge losses, and with vaneless space loss between stator and rotor, and with rotor incidence, viscous, clearance, trailing-edge, and disk friction losses.

Meitner, P. L.↗
NASA NTRS1985

Future directions in aeropropulsion technology

Future directions in aeropropulsion technology that have been identified in a series of studies recently sponsored by the U.S. Government are discussed. Advanced vehicle concepts that could become possible by the turn of the century are presented along with some of their projected capabilities. Key building-block propulsion technologies that will contribute to making these vehicle concepts a reality are discussed along with projections of their status by the year 2000. Some pertinent highlights of the NASA aeropropulsion program are included in the discussion.

Saunders, N. T.↗
NASA NTRS1985

Future directions in aeropropulsion technology

Future directions in aeropropulsion technology that have been identified in a series of studies recently sponsored by the U.S. Government are discussed. Advanced vehicle concepts that could become possible by the turn of the century are presented along with some of their projected capabilities. Key building-block propulsion technologies that will contribute to making these vehicle concepts a reality are discussed along with projections of their status by the year 2000. Some pertinent highlights of the NASA aeropropulsion program are included in the discussion.

Saunders, N. T.↗
NASA NTRS1983

Computer code for off-design performance analysis of radial-inflow turbines with rotor blade sweep

The analysis procedure of an existing computer program was extended to include rotor blade sweep, to model the flow more accurately at the rotor exit, and to provide more detail to the loss model. The modeling changes are described and all analysis equations and procedures are presented. Program input and output are described and are illustrated by an example problem. Results obtained from this program and from a previous program are compared with experimental data.

Meitner, P. L.↗
NASA NTRS1983

Input generator for Denton 3-dimensional turbomachine-blade-row analysis code

A users manual is presented for a computer program that prepares the bulk of the input data set required for the Denton three dimensional turbomachine blade row analysis code. The Denton input is generated from a minimum of geometry and flow variable information by using cubic spline curve fitting procedures. The features of the program are discussed. The input is described and special instructions are included to assist in its preparation. Sample input and output are included.

Glassman, A. J.↗
NASA NTRS1980

Off-design performance loss model for radial turbines with pivoting, variable-area stators

An off-design performance loss model was developed for variable stator (pivoted vane), radial turbines through analytical modeling and experimental data analysis. Stator loss is determined by a viscous loss model; stator vane end-clearance leakage effects are determined by a clearance flow model. Rotor loss coefficient were obtained by analyzing the experimental data from a turbine rotor previously tested with six stators having throat areas from 20 to 144 percent of design area and were correlated with stator-to-rotor throat area ratio. An incidence loss model was selected to obtain best agreement with experimental results. Predicted turbine performance is compared with experimental results for the design rotor as well as with results for extended and cutback versions of the rotor. Sample calculations were made to show the effects of stator vane end-clearance leakage.

Meitner, P. L.↗
NASA NTRS1980

Loss model for off-design performance analysis of radial turbines with pivoting-vane, variable-area stators

An off-design performance loss model for a radial turbine with pivoting, variable-area stators is developed through a combination of analytical modeling and experimental data analysis. A viscous loss model is used for the variation in stator loss with setting angle, and stator vane end-clearance leakage effects are predicted by a clearance flow model. The variation of rotor loss coefficient with stator setting angle is obtained by means of an analytical matching of experimental data for a rotor that was tested with six stators, having throat areas from 20 to 144% of the design area. An incidence loss model is selected to obtain best agreement with experimental data. The stator vane end-clearance leakage model predicts increasing mass flow and decreasing efficiency as a result of end-clearances, with changes becoming significantly larger with decreasing stator area.

Meitner, P. L.↗
NASA NTRS1980

Some advantages of methane in an aircraft gas turbine

Because liquid methane may be obtained from existing natural gas sources or produced synthetically from a range of other hydrocarbon sources (coal, biomass, shale, organic waste), it is considered as an aviation fuel in a simplified cycle analysis of the performance of a turboprop engine intended for operation at Mach 0.8 and 10,688 m altitude. Performance comparisons are given for four cases in which the turbine cooling air is either not cooled or cooled to -111, -222, and -333 K, and the advantages and problems that may be expected from direct use of the cryogenic fuel in turbine cooling are discussed. It is shown that while (1) methane combustion characteristics are appreciably different from those of Jet A fuel and will require the development of different combustor designs, and (2) the safe integration of methane cryotanks into transport aircraft structures poses a major design problem, a highly fuel-efficient turboprop engine fueled by methane appears to be feasible.

Graham, R. W.↗
NASA NTRS1980

Loss model for off-design performance analysis of radial turbines with pivoting-vane, variable-area stators

An off-design performance loss model is developed for variable-area (pivoted vane) radial turbines. The variation in stator loss with stator area is determined by a viscous loss model while the variation in rotor loss due to stator area variation (for no stator end-clearance gap) is determined through analytical matching of experimental data. An incidence loss model is also based on matching of the experimental data. A stator vane end-clearance leakage model is developed and sample calculations are made to show the predicted effects of stator vane end-clearance leakage on performance.

Meitner, P. L.↗
NASA NTRS1980

Some advantages of methane in an aircraft gas turbine

Liquid methane, which can be manufactured from any of the hydrocarbon sources such as coal, shale biomass, and organic waste considered as a petroleum replacement for aircraft fuels. A simple cycle analysis is carried out for a turboprop engine flying a Mach 0.8 and 10, 688 meters (35,000 ft.) altitude. Cycle performance comparisions are rendered for four cases in which the turbine cooling air is cooled or not cooled by the methane fuel. The advantages and disadvantages of involving the fuel in the turbine cooling system are discussed. Methane combustion characteristics are appreciably different from Jet A and will require different combustor designs. Although a number of similar difficult technical problems exist, a highly fuel efficient turboprop engine burning methane appear to be feasible.

Graham, R. W.↗
NASA NTRS1980

NASA contributions to radial turbine aerodynamic analyses

A brief description of the radial turbine and its analysis needs is followed by discussions of five analytical areas; design geometry and performance, off design performance, blade row flow, scroll flow, and duct flow. The functions of the programs, areas of applicability, and limitations and uncertainties are emphasized. Both past contributions and current activities are discussed.

Glassman, A. J.↗
NASA NTRS1976

Computer program for design analysis of radial-inflow turbines

A computer program written in FORTRAN that may be used for the design analysis of radial-inflow turbines was documented. The following information is included: loss model (estimation of losses), the analysis equations, a description of the input and output data, the FORTRAN program listing and list of variables, and sample cases. The input design requirements include the power, mass flow rate, inlet temperature and pressure, and rotational speed. The program output data includes various diameters, efficiencies, temperatures, pressures, velocities, and flow angles for the appropriate calculation stations. The design variables include the stator-exit angle, rotor radius ratios, and rotor-exit tangential velocity distribution. The losses are determined by an internal loss model.

Glassman, A. J.↗
NASA NTRS1975

FORTRAN program for predicting off-design performance of radial-inflow turbines

The FORTRAN IV program uses a one-dimensional solution of flow conditions through the turbine along the mean streamline. The program inputs needed are the design-point requirements and turbine geometry. The output includes performance and velocity-diagram parameters over a range of speed and pressure ratio. Computed performance is compared with the experimental data from two radial-inflow turbines and with the performance calculated by a previous computer program. The flow equations, program listing, and input and output for a sample problem are given.

Wasserbauer, C. A.↗
NASA NTRS1975

Turbine Design and Application, Volume 3

Turbine technology concepts for thermodynamic and fluid dynamics are presented along with velocity diagrams, losses, mechanical design, operation and performance. Designs discussed include: supersonic turbines, radial-inflow turbines, and turbine cooling.

Glassman, A. J.↗