Engineering Papers⌕ Search

Engineering topics

Giles, G. L.

Publications and source records attributed to Giles, G. L..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Computer-aided methods for analysis and synthesis of supersonic cruise aircraft structures

Computer-aided methods are reviewed which are being developed by Langley Research Center in-house work and by related grants and contracts. Synthesis methods to size structural members to meet strength and stiffness (flutter) requirements are emphasized and described. Because of the strong interaction among the aerodynamic loads, structural stiffness, and member sizes of supersonic cruise aircraft structures, these methods are combined into systems of computer programs to perform design studies. The approaches used in organizing these systems to provide efficiency, flexibility of use in an iterative process, and ease of system modification are discussed.

Giles, G. L.↗
NASA NTRS1975

Simultaneous calculation of aircraft design loads and structural member sizes

A design process which accounts for the interaction between aerodynamic loads and changes in member sizes during sizing of aircraft structures is described. A simultaneous iteration procedure is used wherein both design loads and member sizes are updated during each cycle yielding converged, compatible loads and member sizes. A description is also given of a system of programs which incorporates this process using lifting surface theory to calculate aerodynamic pressure distributions, using a finite-element method for structural analysis, and using a fully stressed design technique to size structural members. This system is tailored to perform the entire process with computational efficiency in a single computer run so that it can be used effectively during preliminary design. Selected results, considering maneuver, taxi, and fatigue design conditions, are presented to illustrate convergence characteristics of this iterative procedure.

Giles, G. L.↗
NASA NTRS1975

Digital computer programs for generating oblique orthographic projections and contour plots

User and programer documentation is presented for two programs for automatic plotting of digital data. One of the programs generates oblique orthographic projections of three-dimensional numerical models and the other program generates contour plots of data distributed in an arbitrary planar region. A general description of the computational algorithms, user instructions, and complete listings of the programs is given. Several plots are included to illustrate various program options, and a single example is described to facilitate learning the use of the programs.

Giles, G. L.↗
NASA NTRS1972

Effects of eccentricities and lateral pressure on the design of stiffened compression panels

An analysis for determining the effects of eccentricities and lateral pressure on the design of stiffened compression panels is presented. The four types of panel stiffeners considered are integral, zee, integral zee, and integral tee. Mass-strength curves, which give the mass of the panel necessary to carry a specified load, are given along with related design equations needed to calculate the cross-sectional dimensions of the minimum-mass-stiffened panel. The results of the study indicate that the proportions of the panels are geometrically similar to the proportions of panels designed for no eccentricity or lateral pressure, but no cross-sectional dimensions are greater, resulting in significantly increased mass. The analytical minimum-mass designs of zee-stiffened panels are compared with designs from experimentally derived charts. An assumed eccentricity of 0.001 times the length of the panel is used to correlate the analytical and experimental data. Good correlation between the experimentally derived and the analytical curves is obtained for the range of loading where materials yield governs the design. At lower loads the mass given by the analytical curve using this assumed eccentricity is greater than that given by the experimental results.

Giles, G. L.↗
NASA NTRS1972

Automated procedures for sizing aerospace vehicle structures /SAVES/

Results from a continuing effort to develop automated methods for structural design are described. A system of computer programs presently under development called SAVES is intended to automate the preliminary structural design of a complete aerospace vehicle. Each step in the automated design process of the SAVES system of programs is discussed, with emphasis placed on use of automated routines for generation of finite-element models. The versatility of these routines is demonstrated by structural models generated for a space shuttle orbiter, an advanced technology transport,n hydrogen fueled Mach 3 transport. Illustrative numerical results are presented for the Mach 3 transport wing.

Giles, G. L.↗
NASA NTRS1971

Structural efficiencies of five compression panels with curved elements

Structural-efficiency analyses are used to determine the minimum-mass proportions of some panel configurations loaded in uniaxial compression. Five panel constructions, four of which incorporate circular-arc elements and the other a beaded-web corrugation, are shown to have improved structural efficiencies over conventional configurations. In addition to the structural-efficiency equations, which give the mass equivalent flat-plate thickness of the panel necessary to carry a given load, related design equations for calculating the cross-sectional dimensions of these minimum-mass panels are presented. The upper and lower limits of loading, where the design constraints of minimum gage or material yield strength become the dominant design conditions, are established and the corresponding design equations which are applicable outside these limits are also presented.

Giles, G. L.↗