Engineering Papers⌕ Search

Engineering topics

Gharibyan, Narek

Publications and source records attributed to Gharibyan, Narek.

At least 19 records

Rapid Quantification of 237 U Specific Activity for Nuclear Forensics

In the event of an unattributed nuclear explosion, rapid assessment of the short-lived uranium isotope activity and mass can provide valuable information for subsequent forensic analysis. Rapid analysis in the field is enabled by using microfluidic chemistry and deployable instrumentation. Here, this work presents a flow chemistry system, controlled in LabVIEW, that integrates three functionalities: (1) selective extraction of uranium from the sample matrix via a 3D-printed supported liquid membrane module; (2) UV–visible absorbance spectrophotometry to measure the total uranium concentration in the strip flow; and (3) a portable CdTe γ-ray spectrometer coupled to a 3D-printed flow cell to measure 237 U activity concentration in the strip solution. The system was calibrated using standard solutions, and its functionality was demonstrated using a solution of depleted uranium spiked with 237 U. Uranium concentrations of 40–5000 μg/mL were directly quantified online using a 100 mm optical flow cell, while concentrations of 0.5–10 μg/mL were quantified online using a colorimetric reagent. The mass concentration measurement takes approximately 60 min while the activity concentration via γ-ray spectrometry varies depending on the activity of 237 U, with 1 kBq/mL requiring about 30 min of acquisition time to obtain <10% uncertainty at 1σ. This platform provides a fieldable approach for quantifying uranium mass and radioactivity relevant to postdetonation nuclear debris.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modular, disposable 3D printed microfluidic membrane system for separation and purification

The present disclosure relates to a membrane extraction apparatus for extracting a component from a first liquid. The apparatus may incorporate a housing comprised of first and second mating housing halves, with each housing half having an open faced channel formed therein such that the channels at least partially overlay one another when the two housing halves are secured together. A membrane filter is disposed between the two housing halves to overlay the open faced channels. The membrane filter extracts the component from the first liquid and transfers the component into the second liquid as the first and second liquids flow through the first and second housing halves.

Servis, Anna G.↗

Radiochemical capabilities for astrophysics experiments at the national ignition facility

The Nuclear and Radiochemistry Group at Lawrence Livermore National Laboratory (LLNL) has developed a suite of diagnostics and techniques that can be used for astrophysics experiments at the National Ignition Facility (NIF). Capabilities have been developed to add material to the outside of NIF hohlraum assemblies as well as to the interior of NIF target capsules or the fill gas. The ability to place very small amounts of material close to the NIF target enables activation with very large, short-pulse neutron fluxes. The Solid Radiochemistry Diagnostic can be used to collect solid debris from a NIF shot within 2 h of the execution of a shot, and this can be analyzed for radioactive signatures with or without post-shot chemical processing. The Radiochemical Analysis of Gaseous Samples diagnostic system can be used to collect gaseous products produced during a NIF shot. Capsule doping and radiochemical analysis capabilities at NIF will be discussed. The application of these techniques to astrophysical measurements will be discussed as well as some preliminary results.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Nuclear Forensics

Nuclear forensics is a key part of the nuclear security strategy for the United States and the international community. The NACS Division is central to the leadership role that LLNL has had in nuclear forensics over the past 25 years. Our current nuclear forensic program includes conducting R&D on provenance and attribution signatures, collaborating with international partners, training the next generation of nuclear forensic experts, developing test materials for verification and validation exercises, and providing expert advice to national and international policy makers. Key to our success in these areas has been the strong and continuing involvement in nuclear forensic casework obtained through law enforcement and intelligence channels as well as our outstanding analytical capabilities. NACS must continue to conduct forward-thinking R&D in nuclear forensics that supports operational programs and addresses intelligence gaps. To maintain leadership in nuclear forensics, we must attract, develop, and retain the best talent. The NNSA has a central leadership role in developing educational initiatives for nuclear forensics. In concert with the Glenn T. Seaborg Institute, the NACS Division will continue to participate in all nuclear forensic educational initiatives (undergraduate, graduate, postdoctoral) and incorporate LLNL’s D&I vision into its student and postdoc recruitment efforts. We will continue to build formal relationships with key academic partners and institutions with active and emerging nuclear forensic research interests. We will also strengthen relationships with NNSA DNN and SSAA funded university consortia (e.g. NSSC, ACE, CNEC, CVT, ETI, MTV), helping them conduct research of interest and relevance to nuclear forensics, while at the same time evaluating and recruiting promising talent from these programs.

07 ISOTOPE AND RADIATION SOURCES↗

Uranium hydride corrosion. II Modeling spatially random growth using reaction and nucleation kinetics

A uranium hydride (UH 3 ) corrosion kinetics model has been developed, based on dimensionally restricted nucleation kinetics, which combines heretofore separate reaction and nucleation kinetics models into a single predictive construct. This theoretical framework accounts for the superficial and random pitting behaviour of UH 3 corrosion. The model can be used to generate the net corrosion surface area and volume fractions for a uranium specimen, generally accounting for its geometric form factor through the surface-to-volume ratio. Furthermore, the combined corrosion kinetics model enables the generation of quantities which may be directly compared to those obtained by non-destructive, non-contact evaluation methods.

36 MATERIALS SCIENCE↗

Transport Modeling of Kinetically Limited Microscale Extraction Systems: Droplet and Supported Liquid Membrane Separations

Microfluidic droplet extraction devices can be used to efficiently measure solute phase transfer kinetics in liquid–liquid extraction systems. In this work, a droplet extraction apparatus was constructed using off-the-shelf and custom 3D printed parts for less than 110 USD. The interfacial kinetics of the transfer of Pu(IV) between an aqueous nitric acid phase and a 5 v/v% tridodecylamine (TDA) in toluene phase were characterized by determining the extent of Pu(IV) transfer between phases at different flow rates. Forward interfacial rate constants calculated from this data using an analytical model are 5.6 × 10 –3 mm s –1 under extraction (aqueous-to-organic solute transfer) conditions and 3.3 × 10 –3 mm s –1 under stripping (organic-to-aqueous solute transfer) conditions. The analytical model is valid when the rate of solute transfer across the interface between the two liquid phases has pseudo-first-order reversible reaction kinetics and is slow relative to the rate of solute transport to the interface. The change in the outlet concentration with residence time determined using the analytical model was compared with the results of a numerical model accounting for advection/diffusion to the interface in addition to kinetically limited interfacial solute transfer. These calculations revealed that for systems with forward interfacial rate constants greater than approximately 10 –2 mm s –1 , the analytical model must be supplemented with a numerical transport model accounting for an additional advection/diffusion mass transfer resistance. This threshold corresponds to a Damköhler number of one. The measured interfacial kinetic rate constants for Pu(IV)/TDA were used in a supported liquid membrane (SLM) numerical model, which showed that the Pu(IV) phase transfer kinetics are fast enough for use in a practical separation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Aqueous harvesting of 88 Zr at a radioactive-ion-beam facility for cross-section measurements

Isotope harvesting is a method of collecting the long-lived radioisotopes that build up during the operation of ion-beam facilities in a way that is useful for subsequent research. As a demonstration of this method for the collection of a group IV metal at a fragmentation facility, the high-energy Zr 88 secondary beam produced from a 140-MeV/u Mo 92 primary beam at the National Superconducting Cyclotron Laboratory (NSCL) was stopped in a water target. The setup aimed to mimic the aqueous beam dump that will be implemented at the Facility for Rare Isotope Beams (FRIB). The collected Zr 88 and accompanying Y 88 decay daughter were radiochemically extracted from the solution and made into target samples suitable for neutron-capture cross-section measurements. These samples were then irradiated at two reactor facilities, and the Zr 88 average thermal-neutron-capture cross section ( σ T ) and resonance integral ( I ) were determined to be σ T = ( 8.04 ± 0.63 ) × 10 5 b and I = ( 2.53 ± 0.28 ) × 10 6 b. The σ T value agrees well with previous results and I , determined for the first time here, was found to be the largest measured resonance integral by two orders of magnitude. The Y 88 thermal-neutron-capture cross section was determined to be less than 1.8 × 10 4 b. This work demonstrates the steps needed to make cross-section measurements with samples produced via aqueous isotope harvesting.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

3D Printed Microfluidic Supported Liquid Membrane Module for Radionuclide Separations

Microfluidic supported liquid membrane extraction is a promising technique for microliter-scale radionuclide separations because it requires very small reagent volumes and combines extraction and stripping in a single unit operation. Flat sheet supported liquid membrane (FS-SLM) modules with 100, 200, 300, and 400 μm deep channels were fabricated at a cost of less than 5 USD in material using a commercially available resin three-dimensional (3D) printer. The performance of these modules was characterized by quantifying uranium transport across a 15 v/v% tributyl phosphate (TBP) liquid membrane at flow rates between 5 and 60 μL min –1 and developing a two-dimensional (2D) numerical transport model for the system. The extent of uranium extraction was found to increase with increasing residence time and decreasing channel depth, with quantitative extraction occurring at the slowest flow rates and shallowest channel depths. The numerical model agreed well with the experimental extraction results. Time-dependent calculations showed that the modules reach steady state in fewer than 9 min and that there is a considerable buildup of uranium in the membrane during that time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Studies of the homologs and pseudo-homologs of flerovium with crown ether based extraction chromatography resins

A crown-ether based extraction chromatography resin, Eichrom Pb, has been characterized for separations of the flerovium (Fl) pseudo-homolog Hg. Previous results on the batch uptake of Pb(II) and Sn(IV) are compared with newly investigated Hg(II) in HCl matrices. It was determined that all three elements can be strongly retained by the resin at different HCl concentrations. To assess the feasibility for performing an experiment on the chemical properties of Fl using this resin the extraction kinetics were studied. In conclusion, a separation method for the isolation of the homologs Pb(II) and Sn(IV) and pseudo-homolog Hg(II) has been established using 2 mL pre-packed Pb resin columns under vacuum flow.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Development of a “fission-proxy” method for the measurement of 14-MeV neutron fission yields

Here, telative fission-yield measurements were made for 50 fission products from 25.6±0.5 MeV α -induced fission of Th-232. Quantitative comparison of these experimentally measured yields with the evaluated fission yields from 14-MeV neutrons on U-235 demonstrates the application of the Bohr-independence hypothesis for measuring fission yields. As optimum particle-target configurations may be impossible or compromised at a given facility, this new approach, fission-proxy, allows the measurement of fission yields for a given compound nucleus from an alternate reaction pathway since formation and subsequent decay are independent processes.

07 ISOTOPE AND RADIATION SOURCES↗

Methodology and Software for Gross Defect Detection of Spent Nuclear Fuel at the Atucha-I Reactor [Novel Methodology and Software for Spent Fuel Gross Defect Detection at the Atucha-I Reactor]

Here, fuel assemblies in the spent fuel pool are stored by suspending them in two vertically stacked layers at the Atucha Unit 1 nuclear power plant (Atucha-I). This introduces the unique problem of verifying the presence of fuel in either layer without physically moving the fuel assemblies. Given that the facility uses both natural uranium and slightly enriched uranium at 0.85 wt% 235 U and has been in operation since 1974, a wide range of burnups and cooling times can exist in any given pool. A gross defect detection tool, the spent fuel neutron counter (SFNC), has been used at the site to verify the presence of fuel up to burnups of 8000 MWd/t. At higher discharge burnups, the existing signal processing software of the tool was found to fail due to nonlinearity of the source term with burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a “Fission-proxy” Method for the Measurement of 14-MeV Neutron Fission Yields at CAMS

Relative fission yield measurements were made for 50 fission products from 25.6±0.5 MeV alpha-induced fission of Th-232. Quantitative comparison of these experimentally measured fission yields with the evaluated fission yields from 14-MeV neutron-induced fission of U-235 demonstrates the feasibility of the proposed fission-proxy method. This new technique, based on the Bohr-independence hypothesis, permits the measurement of fission yields from an alternate reaction pathway (Th-232 + 25.6 MeV α → U-236* vs. U-235 + 14-MeV n → U-236*) given that the fission process associated with the same compound nucleus is independent of its formation. Other suitable systems that can potentially be investigated in this manner include (but are not limited to) Pu-239 and U-237.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Characterization of the homologs of flerovium with crown ether based extraction chromatography resins: studies in nitric acid

Eichrom’s Pb resin, a crown-ether-based extraction chromatography resin, was characterized for separation of the flerovium (Fl) homologs, Pb and Sn. Batch uptake of Pb(II) and Sn(IV) radionuclides was determined from an HNO 3 matrix. Pb(II) was strongly retained on the resin at all HNO 3 concentrations, while Sn(IV) showed no uptake. Extraction kinetics for Pb(II) were examined and show suitable uptake on the second time scale. Here, separation methods for the isolation of individual homologs, Pb(II) and Sn(IV), have been established using 2 mL pre-packed vacuum flow Pb resin columns.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Non-destructive analysis of DU content in the NIF hohlraums

The advantage of using depleted uranium (DU) hohlraums in high-yield deuterium-tritium (DT) shots at the National Ignition Facility (NIF) is addressed by Döppner, et al., in great detail [1]. This DU based hohlraum incorporates a thin layer of DU, ~7 μm thick, on the inner surface along with a thin layer of a gold coating, ~0.7 μm thick, while the outer layer is ~22 μm thick gold. A thickness measurement of the DU layer can be performed using an optical microscope where the total DU weight can be computed provided a uniform DU layer. However, the uniformity of the thickness is not constant throughout the hohlraum since CAD drawing calculations of the DU weight do not agree with the computed values from optical measurements [2]. Therefore, a non-destructive method for quantifying the DU content in hohlraums has been established by utilizing gamma-ray spectroscopy. The details of this method, along with results from several hohlraums, are presented in this report.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Production and isolation of homologs of flerovium and element 115 at the Lawrence Livermore National Laboratory Center for Accelerator Mass Spectrometry

Here, new procedures have been developed to isolate no-carrier-added (NCA) radionuclides of the homologs and pseudo-homologs of flerovium (Hg, Sn) and element 115 (Sb), produced by 12–15 MeV proton irradiation of foil stacks with the tandem Van-de-Graaff accelerator at the Lawrence Livermore National Laboratory Center for Accelerator Mass Spectrometry (CAMS) facility. The separation of 113 Sn from nat In foil was performed with anion-exchange chromatography from hydrochloric and nitric acid matrices. A cation-exchange chromatography method based on hydrochloric and mixed hydrochloric/hydroiodic acids was used to separate 124 Sb from nat Sn foil. A procedure using Eichrom TEVA resin was developed to separate 197 Hg from Au foil. These results demonstrate the suitability of using the CAMS facility to produce NCA radioisotopes for studies of transactinide homologs.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗