Engineering Papers⌕ Search

Engineering topics

Gelbard, Fred

Publications and source records attributed to Gelbard, Fred.

At least 19 records

SFM - Sandia Fireball Model

SAND2022-13231 O Sandia Fireball Model is used in the assessment of liquid propellant fireballs in the source term analysis for space nuclear systems launch safety. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Powers, Dana↗

MELCOR Accident Progression and Source Term Demonstration Calculations for a FHR

MELCOR is an integrated thermal hydraulics, accident progression, and source term code for reactor safety analysis that has been developed at Sandia National Laboratories for the United States Nuclear Regulatory Commission (NRC) since the early 1980s. Though MELCOR originated as a light water reactor (LWR) code, development and modernization efforts have expanded its application scope to include non-LWR reactor concepts. Current MELCOR development efforts include providing the NRC with the analytical capabilities to support regulatory readiness for licensing non-LWR technologies under Strategy 2 of the NRC's near- term Implementation Action Plans. Beginning with the Next Generation Nuclear Project (NGNP), MELCOR has undergone a range of enhancements to provide analytical capabilities for modeling the spectrum of advanced non-LWR concepts. This report describes the generic plant model developed to demonstrate MELCOR capabilities to perform fluoride-salt-cooled high-temperature reactor (FHR) safety evaluations. The generic plant model is based on publicly-available FHR design information. For plant aspects (e.g., reactor building leak rate and details of the cover-gas system) that are not described in the FHR references, the analysts made assumptions needed to construct a MELCOR full-plant model. The FHR model uses a TRi-structural ISOtropic (TRISO)-particle fuel pebble-bed reactor with a primary system rejecting heat to two coiled tube air heat ex changers. Three passive direct reactor auxiliary cooling systems provide heat removal to supplement or replace the emergency secondary system heat removal during accident conditions. Surrounding the reactor vessel is a low volume reactor cavity that insulates the reactor with fire bricks and thick concrete walls. A refractory reactor liner system provides water cooling to reduce the concrete wall temperatures. Example calculations are performed to show the plant response and MELCOR capabilities to characterize a range of accident conditions. The accidents selected for evaluation consider a range of degraded and failed modes of operation for key safety functions providing reactivity control, the primary system decay heat removal and also a piping leak of the line to the coolant drain tank.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Identification and Resolution of Gaps in Mechanistic Source Term and Consequence Analysis Modeling for Molten Salt Reactors Salt Spill Scenarios

This report represents an assessment of the gaps in Mechanistic Source Term (MST) and consequence assessment modeling for Molten Salt Reactors (MSRs). The current capabilities for MELCOR and the MELCOR Accident Code System (MACCS) are discussed, along with updates needed in order to address specific needs for MSRs. A test plan developed by Argonne National Laboratories is discussed as addressing some of these gaps, while some will require additional attention. Further recommendations are made on addressing these gaps. This report satisfies the DOE NE Milestone M2RD-21SN0601061 to leverage MELCOR and MACCS to identify parameters of importance for source term assessments for salt spill experiments.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

MELCOR Code Change History: Revision 18019 to 21402

This document summarily provides brief descriptions of the MELCOR code enhancement made between code revision number 18019and 21440. Revision 18019 represents the previous official code release; therefore, the modeling features described within this document are provided to assist users that update to the newest official MELCOR code release, 21440. Along with the newly updated MELCOR Users’ Guide [2] and Reference Manual [3], users are aware and able to assess the new capabilities for their modeling and analysis applications.

97 MATHEMATICS AND COMPUTING↗

Effective Permeability of a Nuclear Fuel Assembly

This report aids in the development of models to perform characterization studies of aerosol dispersal and deposition within a spent fuel cask system. Due to the complex geometry in a spent-fuel canister, direct simulation of buoyancy-driven flow through the fuel assemblies to model aerosol deposition within the fuel canister is computationally expensive. Identification of an effective permeability as given in this work for a nuclear fuel assembly greatly simplifies the requirements for thermal hydraulic computations. The results of computations performed using OpenFOAM® to solve the Navier-Stokes Equations for laminar flow are used to determine an effective permeability by applying Darcy's Law. The computations are validated against an analytical solution for the special case of an infinite array of pins for which the numerical and analytical solutions have excellent agreement. The effective permeability of a 1717 PWR nuclear fuel assembly in a basket without spacer grids is numerically determined to be 1.85010 -6 m 2 for the range of fluid viscosities and pressure drops expected in a spent fuel storage canister. However, the flow is not uniform on the scale of multiple pins. Instead, significantly higher velocities are attained in the space between the assembly and the basket walls compared to the flow between the fuel pins within the assembly. Comparison with an analytical solution for fully developed flow through an infinite array of pins shows that the larger spacing near the basket walls results in about a 20% larger permeability compared to the analytical solution which does not include the enhanced flow in the space between the assembly and basket wall, or entrance and exit effects. A preliminary assessment of turbulence effects shows that with a k-epsilon model, significantly higher flow velocities are attained between the fuel pins within the assembly compared to the flow velocity in the space between the assembly and the basket walls. This is the opposite of what is determined for laminar flow.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Aerosol Deposition Inside a Spent Fuel Transportation and Storage Canister (Interim Report)

This report documents the progress in preparing the ANSYS/Fluent ® and MELCOR models to perform characterization studies of aerosols dispersal and deposition within a select spent fuel cask system. Steady state thermal-hydraulic cask response is modeled with both codes, at present, while the MELCOR source code is being modified to allow imposed thermal-hydraulic conditions with aerosol physics calculations. This will allow the MELCOR model to assume the thermal-hydraulic calculation from the ANSYS/Fluent ® , while only computing the aerosol physics. Detailed results are presented on the thermal-hydraulic analysis of the MAGNASTOR ® cask for the current ANSYS/Fluent ® model, with convergent conditions observed over two fidelities. While the MELCOR computation computes the steady state conditions, they differ sufficiently from that computed with ANSYS/Fluent ® . The MELCOR analysis include a set of UO 2 sources to investigate system response for interim reporting. The airborne concentrations and evolving distributions are presented. Model development is anticipated to continue as additional components impacting flow conditions or aerosol deposition within the MAGNASTOR ® cask and Westinghouse fuel assemblies are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

OWL and Waste Form Characteristics (Annual Status Update)

This report represents completion of milestone deliverable M2SF-21SN010309012 “Annual Status Update for OWL and Waste Form Characteristics” that provides an annual update on status of fiscal year (FY 2020) activities for the work package SF-20SN01030901 and is due on January 29, 2021. The Online Waste Library (OWL) has been designed to contain information regarding United States (U.S.) Department of Energy (DOE)-managed (as) high-level waste (DHLW), spent nuclear fuel (SNF), and other wastes that are likely candidates for deep geologic disposal, with links to the current supporting documents for the data (when possible; note that no classified or official-use-only (OUO) data are planned to be included in OWL). There may be up to several hundred different DOE-managed wastes that are likely to require deep geologic disposal. This draft report contains versions of the OWL model architecture for vessel information (Appendix A) and an excerpt from the OWL User’s Guide (Appendix B and SNL 2020), which are for the current OWL Version 2.0 on the Sandia External Collaboration Network (ECN).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗