Engineering Papers⌕ Search

Engineering topics

Geisz, John F

Publications and source records attributed to Geisz, John F.

Development of Solar Cells with Trapezoidal Grid Fingers

In concentrator solar cells, traditional metallic contacts cover a substantial portion of the device area, resulting in reflected light that diminishes the amount of current collected. In this paper, we developed trapezoidal front grid fingers to decrease the optical shadowing and the resulting loss of the device short-circuit current. By using a negative photoresist, a thick metal layer can be deposited by metal evaporation. The formation of an organic and metallic reflective deposit under the negative sloped photoresist is observed, though. By removing this deposit, a similar short-circuit current to typical Ni/Au contacts deposited by electrodeposition is obtained. Even though the Ti/Al grid fingers have larger width, they have the same effective shadowing due to the trapezoidal shape. At high concentration, a higher efficiency is obtained as well due to a high fill factor and improved open circuit voltage.

14 SOLAR ENERGY↗

Enabling Ultrathin III-V Solar Cells Using Dual Photonic Crystals

III-V materials provide the highest efficiencies, but the higher cost of these materials compared to other alternatives such as silicon has limited their applications. One way of reducing the costs is by minimizing the amount of material needed. In this work, using optical simulations we test light trapping layers in the front and in the back of a GaAs single junction solar cell. By using these layers, we predict that we can obtain near optically thick GaAs single junctions with only 300 nm active material, with maximum calculated J sc of 28.7 mA/cm 2 under the radiative limit.

14 SOLAR ENERGY↗

Fabrication of Thin III-V Solar Cells on Ni Films using Electroless Ni Deposition

Thin solar cells are inherently fragile, and must be properly supported during fabrication, handling and use. Metal films can provide this support, but accomplishing this can be challenging. Here we describe a method for fabricating thin III-V solar cells on Ni films, using electroless deposition to deposit a thick (10-50 um) Ni film onto the bottom of an inverted III-V solar cell prior to substrate removal. Cells have been fabricated on both rigid and flexible supports with no loss of performance when compared to cells processed using standard inverted-cell processing.

14 SOLAR ENERGY↗

Luminescent Solar Concentrator Tandem-on-Silicon with above 700mV Passivated Contact Silicon Bottom Cell

Luminescent solar concentrator (LSC) tandem-on-silicon (Si) provides a route towards achieving higher than 30% overall efficiency which can overcome the theoretical efficiency limit of a single junction Si cell. Here, we present optical coupling and performance of high Voc passivated contact Si bottom cell for LSC tandem-on-Si where the top module consists of highly efficient luminophores and an array of micro InGaP cells embedded in a poly (lauryl methacrylate) waveguide. In this device configuration, InGaP cell area coverage is only ~0.5% of the total LSC area which significantly reduces the high cost III-V material usage. The performance of Si sub-cell is investigated under LSC spectrum and is compared against the measurement done under 1 um thick InGaP filter which mimics the spectrum seen by Si bottom cell in a conventional III-V/Si tandem. V oc of greater than 700 mV has been observed for the passivated contact Si bottom cell in these tandem applications.

14 SOLAR ENERGY↗

Impact of Compositional Fluctuation on Dislocations in Metamorphic III-V Solar Cells Revealed by Cathodoluminescense Spectrum Imaging

Compositionally graded buffers (CGBs) are essential components of high-efficiency III-V inverted metamorphic solar cells. High-quality CGBs with low defect densities are a requirement for high device efficiencies. In this work we use cathodoluminescence spectrum imaging to investigate the effect of growth conditions on the material properties of AlyGa1-x-yInxAs CGBs with xIn = > 0.30. We find that significant compositional fluctuation exists in these materials, and that it correlates with the distribution of threading dislocations in the CGBs. Threading dislocations collect in regions with large compositional fluctuation, implying that concurrent strain fluctuations in these regions restrict dislocation motion. Thus, the compositional fluctuation leads to elevated threading dislocation densities that degrade CGB quality. We investigate the effectiveness of specific growth conditions at suppressing compositional fluctuation and limiting threading dislocation density, and find that CGBs grown at high temperatures with high Al-content exhibit the lowest defect densities. We also demonstrate that use of a high V/III ratio also suppresses compositional fluctuation and defect density. These materials insights lead directly to the development of metamorphic Ga1-xInxAs solar cells grown on AlyGa1-x-yInxAs CGBs with improved device efficiency.

14 SOLAR ENERGY↗

Printed assemblies of microscale triple–junction inverted metamorphic GaInP/GaAs/InGaAs solar cells

Inverted metamorphic (IMM) multijunction solar cells represent a promising material platform for ultrahigh efficiency photovoltaic systems (UHPVs) with a clear pathway to beyond 50% efficiency. The conventional device processing of IMM solar cells, however, typically involves wafer bonding of a centimeter-scale die and destructive substrate removal, thereby imposing severe restrictions in achievable cell size, type of module substrate, spatial layout, as well as cost effectiveness. Here, we report material design and fabrication strategies for microscale triple-junction IMM (3J IMM) Ga 0.51 In 0.49 P/GaAs/In 0.26 Ga 0.74 As solar cells that can overcome these difficulties. Specialized schemes of delineation and undercut etching enable the defect-free release of microscale IMM solar cells and printed assemblies on a glass substrate in a manner that preserves the growth substrate, where efficiencies of 27.3% and 33.9% are demonstrated at simulated AM1.5D one- and 351 sun illumination, respectively. A composite carrier substrate where released IMM microcells are formed in fully functional, print-ready configurations allows high-throughput transfer printing of individual IMM microcells in a programmable spatial layout on versatile choices of module substrate, all desired for CPV applications.

14 SOLAR ENERGY↗

HVPE-Grown GaAs//Si Tandem Device Performance

The performance of III-V//Si tandem devices has successfully exceeded the theoretical efficiency limit of single junction Si devices (29.4%) yet the costs associated with these high-efficiency tandem devices are still too high to compete with today's conventional Si solar cells. Recent cost modeling efforts suggest that hydride vapor phase epitaxy (HVPE) could be adopted as an alternative growth technique to metal-organic chemical vapor deposition (MOCVD) because the costs of HVPE are substantially lower and the performance of devices fabricated from HVPE materials are continuously improving. This study reports on our first results of a HVPE-grown GaAs top cell mechanically stacked on a Si bottom cell.

14 SOLAR ENERGY↗

Effect of Atmospheric Absorption Bands on the Optimal Design of Multijunction Solar Cells

The optimization of subcell bandgaps for seriesconnected multijunction solar cells is complicated by atmospheric absorption bands in terrestrial spectra, and this complexity increases with the number of subcells. We systematically characterize the resulting design space, and introduce a taxonomy for MJ cells based upon the position of subcell bandgaps with respect to atmospheric absorption bands. Once this is done, the full set of local efficiency optima can be quickly identified and described for arbitrarily large numbers of junctions, and deviations from current-matched designs can be more easily characterized and understood.

14 SOLAR ENERGY↗

Mechanically Stacked 4-Terminal III-V/Si Tandem Solar Cells

We developed 4-terminal III-V/Si dual-junction solar cells that reach certified record 1-sun efficiencies over 32%. These efficiency values exceed the theoretical efficiency limit of single-junction solar cells and prove the high potential of Si-based multi-junction devices for next-generation solar panels.

14 SOLAR ENERGY↗

Printed Assemblies of Microscale Triple-Junction (3J) Inverted Metamorphic (IMM) GaInP/GaAs/InGaAs Solar Cells

Transfer printing of microscale devices has been shown to be a manufacturable pathway to low-profile, low cost, high concentration photovoltaic modules, where extremely high efficiency solar cells are desirable to achieve competitive costs. Inverted metamorphic multijunction (IMM) solar cells represent a promising platform for ultrahigh efficiency concentrator photovoltaic systems with a clear pathway to 50% efficiency. While transfer printing of microscale solar cell devices has been demonstrated with traditional upright solar cell structures, IMM structures present additional processing challenges. We demonstrate, for the first time, the transfer printing of fully-functional microscale triple-junction (3J) IMM solar cells.

14 SOLAR ENERGY↗

Absorption Enhancement in InGaAsP/InGaP Quantum Well Solar Cells

InGaAsP/InGaP quantum well (QW) structure is a potential candidate for subcells in next-generation multijunction solar cells because of its tunable bandgap (1.5-1.8 eV). However, the insufficient light absorption in the QWs has previously limited the sub-bandgap quantum efficiency (QE) to less than 25%. We report on the development of InGaAsP/InGaP superlattice solar cell with improved sub-bandgap QE exceeding 75% and bandgap-voltage offset of 0.40 V. The enhancements were accomplished by reducing the background doping in the QW region, monitoring the stress evolution during growth, modifying the QW design to grow thicker wells and processing the devices with optical reflector to enhance light absorption.

14 SOLAR ENERGY↗

Six-Junction Concentrator Solar Cells

We report on six-junction inverted metamorphic (6J IMM) solar cells developed for concentrator applications. Monolithic III-V structures are grown by metal organic vapor phase epitaxy with junction bandgaps of 2.06, 1.70, 1.40, 1.16, 0.94, and 0.70 eV. The top three junctions are lattice-matched to the GaAs substrate, but the bottom three junctions use three consecutive metamorphic compositionally graded buffers to transition the lattice constant to GaxIn1-xAs compositions with the previously listed bandgaps. Performance of 6J IMM devices at one-sun AM1.5 Direct conditions gives VOC = 5.301 V, JSC = 8.05 mA/cm2, fill factor=83.9%, and efficiency=35.8%. Promising operation at high concentration is achieved but the spectrum was not controlled to AM1.5D. Tunnel junctions do not limit until at least several hundred suns. High concentration performance appears to be limited by internal heterojunction barriers created by zinc diffusion that decreases the fill factor. The properties of each junction within the 6J IMM have been separately characterized through electroluminescence and luminescent coupling measurements.

14 SOLAR ENERGY↗

Mechanically Stacked Dual-Junction and Triple-Junction III-V/Si-IBC Cells with Efficiencies Exceeding 31.5% and 35.4%: Preprint

Despite steady advancements in the efficiency of crystalline Silicon (c-Si) photovoltaics (PV) within the last decades, the theoretical efficiency limit of 29.4 percent depicts an insurmountable barrier for silicon-based single-junction solar cells. Combining the Si cell with a second absorber material on top in a dual junction tandem or triple junction solar cell is an attractive option to surpass this limit significantly. We demonstrate a mechanically stacked GaInP/Si dual-junction cell with an in-house measured efficiency of 31.5 percent and a GaInP/GaAs/Si triple-junction cell with a certified efficiency of 35.4 percent.

14 SOLAR ENERGY↗

Pathway to 50% Efficient Inverted Metamorphic Concentrator Solar Cells

Series-connected five (5J) and six junction (6J) concentrator solar cell strategies have the realistic potential to exceed 50% efficiency to enable low-cost CPV systems. We propose three strategies for developing a practical 6J device. We have overcome many of the challenges required to build such concentrator solar cell devices: We have developed 2.1 eV AlGaInP, 1.7 eV AlGaAs, and 1.7 eV GaInAsP junctions with external radiative efficiency greater than 0.1%. We have developed a transparent tunnel junction that absorbs minimal light intended for the second junction yet resists degradation under thermal load. We have developed metamorphic grades from the GaAs to the InP lattice constant that are transparent to sub-GaAs bandgap light. We have grown and compared low bandgap junctions (0.7eV - 1.2 eV) using metamorphic GaInAs, metamorphic GaInAsP, and GaInAsP lattice-matched to InP. And finally, we have demonstrated excellent performance in a high voltage, low current 4 junction inverted metamorphic device using 2.1, 1.7, 1.4, and 1.1 eV junctions with over 8.7 mA/cm2 one-sun current density that operates up to 1000 suns without tunnel junction failure.

14 SOLAR ENERGY↗

Multi-junction solar cell device

A multi-junction solar cell device (10) is provided. The multi-junction solar cell device (10) comprises either two or three active solar cells connected in series in a monolithic structure. The multi-junction device (10) comprises a bottom active cell (20) having a single-crystal silicon substrate base and an emitter layer (23). The multi-junction device (10) further comprises one or two subsequent active cells each having a base layer (32) and an emitter layer (23) with interconnecting tunnel junctions between each active cell. At least one layer that forms each of the top and middle active cells is composed of a single-crystal III-V semiconductor alloy that is substantially lattice-matched to the silicon substrate (22). The polarity of the active p-n junction cells is either p-on-n or n-on-p. The present invention further includes a method for substantially lattice matching single-crystal III-V semiconductor layers with the silicon substrate (22) by including boron and/or nitrogen in the chemical structure of these layers.

Friedman, Daniel J↗