Engineering Papers⌕ Search

Engineering topics

Gates, Bruce C.

Publications and source records attributed to Gates, Bruce C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Remotely Bonded Bridging Dioxygen Ligands Enhance Hydrogen Transfer in a Silica-Supported Tetrairidium Cluster Catalyst

A longstanding challenge in catalysis by noble metals has been to understand the origin of enhancements of rates of hydrogen transfer that result from bonding of oxygen near metal sites. We investigated structurally well-defined catalysts consisting of supported tetrairidium carbonyl clusters with single-atom (apical iridium) catalytic sites for ethylene hydrogenation. Reaction of the clusters with ethylene and H 2 followed by O 2 led to the onset of catalytic activity as a terminal CO ligand at each apical Ir atom was removed and bridging dioxygen ligands replaced CO ligands at neighboring (basal-plane) sites. The presence of the dioxygen ligands caused a 6-fold increase in the catalytic reaction rate, which is explained by the electron-withdrawing capability induced by the bridging dioxygen ligands, consistent with the inference that reductive elimination is rate determining. Electronic structure calculations demonstrate an additional role of the dioxygen ligands, changing the mechanism of hydrogen transfer from that involving equatorial hydride ligands to that involving bridging hydride ligands. This mechanism is made evident by an inverse kinetic isotope effect observed in ethylene hydrogenation reactions with H 2 and, alternatively, with D 2 on the cluster incorporating the dioxygen ligands, and is a consequence of quasi-equilibrated hydrogen transfer in this catalyst. The same mechanism accounts for rate enhancements induced by the bridging dioxygen ligands for the catalytic reaction of H 2 with D 2 to give HD. Here, we posit that the mechanism involving bridging hydride ligands facilitated by oxygen ligands remote from the catalytic site may have some generality in catalysis by oxide-supported noble metals.

02 PETROLEUM↗
DOE OSTI2023

Catalysts Prepared from Atomically Dispersed Ce(III) on MgO Rival Bulk Ceria for CO Oxidation

Atomically dispersed cerium catalysts on an inert, crystalline MgO powder support were prepared by using both Ce(III) and Ce(IV) precursors. The materials were used as catalysts for CO oxidation in a once-through flow reactor and characterized by atomic-resolution scanning transmission electron microscopy, X-ray absorption near edge structure spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed reduction, among other techniques, before and after catalysis. The most active catalysts, formed from the precursor incorporating Ce(III), displayed a performance similar to that reported for bulk ceria under comparable conditions. The catalyst provided stable time-on-stream performance for as long as it was kept on stream, two days, increasing slightly in activity as the atomically dispersed cerium ions were transformed into ceria nanodomains represented as CeO x and having increased reducibility on the MgO support. Furthermore, the results suggest how highly dispersed supported ceria catalysts with low cerium loadings can be prepared and may pave the way to improved efficiencies of cerium utilization in oxidation catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomically dispersed zeolite-supported rhodium complex: Selective and stable catalyst for acetylene semi-hydrogenation

In this study, supported rhodium catalysts are known to be unselective for semi-hydrogenation reactions. Here, by tuning the electronic structure of supported mononuclear rhodium sites determined by the metal nuclearity and the electron-donor properties of the support, we report that atomically dispersed HY zeolite-supported rhodium with reactive acetylene ligands affords a stable ethylene selectivity > 90 % for acetylene semi-hydrogenation at 373 K and atmospheric pressure, even when ethylene is present in a large excess over acetylene. Infrared and X-ray absorption spectra and measurements of rates of the catalytic reaction complemented with calculations at the level of density functional theory show how the catalyst performance depends on the electronic structure of the rhodium, influenced by the support as a ligand that is a weak electron donor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Characterization, Structure, and Reactivity of Hydroxyl Groups on Metal‐Oxide Cluster Nodes of Metal–Organic Frameworks: Structural Diversity and Keys to Reactivity and Catalysis

Among the most stable metal–organic frameworks (MOFs) are those incorporating nodes that are metal oxide clusters with frames such as Zr 6 O 8 . This review is a summary of the structure, bonding, and reactivity of MOF node hydroxyl groups, emphasizing those bonded to nodes containing aluminum and zirconium ions. Hydroxyl groups are often present on these nodes, sometimes balancing the charges of the metal ions. They arise during MOF syntheses in aqueous media or in post-synthesis treatments. They are identified with infrared and 1 H nuclear magnetic resonance spectroscopies and characterized by their reactivities with polar compounds such as alcohols. Terminal OH, paired µ 2 -OH, and aqua groups on nodes are catalytic sites in numerous reactions. Relatively unreactive hydroxyl groups (such as isolated µ 2 -OH groups) may replace reactive groups and inhibit catalysis; some node hydroxyl groups (e.g., µ 3 -OH) are mere spectators in catalysis. There are similarities between MOF node hydroxyl groups and those on the surfaces of bulk metal oxides, zeolites, and enzymes, but the comparisons are mostly inexact, and much remains to be understood about MOF node hydroxyl group chemistry. It is posited that understanding and controlling this chemistry will lead to tailored MOFs and improved adsorbents and catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Observations of Ethylene-for-CO Ligand Exchanges on a Zeolite-Supported Single-Site Rh Catalyst by X-ray Absorption Spectroscopy

Quick-scanning X-ray absorption fine structure (QXAFS) measurements were used to characterize the exchanges of ethylene and CO ligands in a zeolite HY-supported single-site Rh complex at a sampling rate of 1.0 Hz. The two ligands were reversibly exchanged on the rhodium, with quantitative results determined for the C 2 H 4 -for-CO exchange that are consistent with a first-order process. The apparent rate constant for the exchange decreased with increasing temperature. Fourier-transform infrared spectra characterizing the C 2 H 4 sorbed in the zeolite showed that the amount decreased with increasing temperature, consistent with the decrease in the exchange rate with increasing temperature. Here the results, illustrating the dynamics of ligand exchanges on a single-site supported metal catalyst, demonstrate the broad emerging applicability of the QXAFS technique for characterizing the dynamics of reactive intermediates on catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Genesis of Active Pt/CeO 2 Catalyst for Dry Reforming of Methane by Reduction and Aggregation of Isolated Platinum Atoms into Clusters

Atomically dispersed metal catalysts offer the advantages of efficient metal utilization and high selectivities for reactions of technological importance. Such catalysts have been suggested to be strong candidates for dry reforming of methane (DRM), offering prospects of high selectivity for synthesis gas without coke formation, which requires ensembles of metal sites and is a challenge to overcome in DRM catalysis. However, investigations of the structures of isolated metal sites on metal oxide supports under DRM conditions are lacking, and the catalytically active sites remain undetermined. Data characterizing the DRM reaction-driven structural evolution of a cerium oxide- supported catalyst, initially incorporating atomically dispersed platinum, and the corresponding changes in catalyst performance are reported. X-ray absorption and infrared spectra show that the reduction and agglomeration of isolated cationic platinum atoms to form small platinum clusters/nanoparticles are necessary for DRM activity. Density functional theory calculations of the energy barriers for methane dissociation on atomically dispersed platinum and on platinum clusters support these observations. Here the results emphasize the need for in-operando experiments to assess the active sites in such catalysts. The inferences about the catalytically active species are suggested to pertain to a broad class of catalytic conversions involving the rate-limiting dissociation of light alkanes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Elucidating correlated defects in metal organic frameworks using theory-guided inelastic neutron scattering spectroscopy

Metal organic frameworks (MOFs) that incorporate metal oxide cluster nodes, exemplified by UiO-66, have been widely studied, especially in terms of their deviations from the ideal, defect-free crystalline structures. Although defects such as missing linkers, missing nodes, and the presence of adventitious synthesis-derived node ligands (such as acetates and formates) have been proposed, their exact structures remain unknown. Previously, it was demonstrated that defects are correlated and span multiple unit cells. The highly specialized techniques used in these studies are not easily applicable to other MOFs. Thus, there is a need to develop new experimental and computational approaches to understand the structure and properties of defects in a wider variety of MOFs. Here, we show how low-frequency phonon modes measured by inelastic neutron scattering (INS) spectroscopy can be combined with density functional theory (DFT) simulations to provide unprecedented insights into the defect structure of UiO-66. We are able to identify and assign peaks in the fingerprint region (<100 cm –1 ) which correspond to phonon modes only present in certain defective topologies. Specifically, this analysis suggests that our sample of UiO-66 consists of predominantly defect-free fcu regions with smaller domains corresponding to a defective bcu topology with 4 and 2 acetate ligands bound to the Zr 6 O 8 nodes. Importantly, the INS/DFT approach provides detailed structural insights (e.g., relative positions and numbers of acetate ligands) that are not accessible with microscopy-based techniques. Furthermore, the quantitative agreement between DFT simulations and the experimental INS spectrum combined with the relative simplicity of sample preparation, suggests that this methodology may become part of the standard and preferred protocol for the characterization of MOFs, and, in particular, for elucidating the structure defects in these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Functional CeO x nanoglues for robust atomically dispersed catalysts

Single-atom catalysts make exceptionally efficient use of expensive noble metals and can bring out unique properties. However, applications are usually compromised by limited catalyst stability, which is due to sintering. Although sintering can be suppressed by anchoring the metal atoms to oxide supports, strong metal–oxygen interactions often leave too few metal sites available for reactant binding and catalysis, and when exposed to reducing conditions at sufficiently high temperatures, even oxide-anchored single-atom catalysts eventually sinter. Here we show that the beneficial effects of anchoring can be enhanced by confining the atomically dispersed metal atoms on oxide nanoclusters or ‘nanoglues’, which themselves are dispersed and immobilized on a robust, high-surface-area support. We demonstrate the strategy by grafting isolated and defective CeO x nanoglue islands onto high-surface-area SiO 2 ; the nanoglue islands then each host on average one Pt atom. Further, we find that the Pt atoms remain dispersed under both oxidizing and reducing environments at high temperatures, and that the activated catalyst exhibits markedly increased activity for CO oxidation. We attribute the improved stability under reducing conditions to the support structure and the much stronger affinity of Pt atoms for CeO x than for SiO 2 , which ensures the Pt atoms can move but remain confined to their respective nanoglue islands. The strategy of using functional nanoglues to confine atomically dispersed metals and simultaneously enhance their reactivity is general, and we anticipate that it will take single-atom catalysts a step closer to practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Dehydrogenation of Propane and n -Butane Catalyzed by Isolated PtZn 4 Sites Supported on Self-Pillared Zeolite Pentasil Nanosheets

Propene and 1,3-butadiene are important building-block chemicals that can be produced by dehydrogenation of propane and butane over Pt catalysts. The challenge is to develop highly active and selective catalysts that are resistant to deactivation by Pt sintering and coke formation. We have recently shown that these objectives can be met for propane dehydrogenation using atomically dispersed Pt atoms anchored to neighboring ≡SiOZn-OH groups bonded to the framework dealuminated zeolite BEA. In the present study, we demonstrate that significantly superior performance can be achieved by using self-pillared pentasil (SPP) zeolite nanosheets. Following catalyst reduction in H 2 , atomic-resolution, scanning transmission electron microscopy (STEM) and X-ray absorption spectroscopy (XAS) indicate that Pt is stabilized in structures well approximated as (≡Si-O-Zn) 4-5 Pt. These species are highly active, selective, and stable for propane dehydrogenation (PDH) to give propene and for n-butane dehydrogenation (BDH) to give 1,3-butadiene. No catalyst deactivation was observed after 12 days of time on stream, and the selectivity remained at nearly 100% for PDH conducted at 823 K and a weight hourly space velocity (WHSV) of 1,350 h -1 . The apparent rate coefficient for PDH over this catalyst is significantly higher than that reported previously for Pt-containing catalysts. For BDH at 823 K and a WHSV of 3560 h -1 , the selectivity to butene isomers and 1,3-butadiene is 98.9%, and the selectivity to 1,3-butadiene is 45%. Here, we propose that the high catalyst stability observed during PDH and BDH is a consequence of a large fraction of the Pt-containing centers being located on the external surface of the zeolite nanosheets, where nascent coke precursors can desorb before condensing to form coke.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Ionic Liquid Sheath Stabilizes Atomically Dispersed Reduced Graphene Aerogel‐Supported Iridium Complexes during Ethylene Hydrogenation Catalysis

Abstract An atomically dispersed reduced graphene aerogel (rGA)‐supported iridium catalyst having reactive ethylene ligands was synthesized at an iridium loading of 9.9 wt % and coated with an ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([EMIM][OAc]). Continuous‐scan X‐ray absorption spectra demonstrated that the iridium remained site‐isolated in flowing equimolar C 2 H 4 and H 2 during a temperature ramp to 100 °C. The data further showed the lack of detectable iridium aggregation when the feed was H 2 ‐rich or even pure H 2 at 100 °C. An Arrhenius plot determined for ethylene hydrogenation catalysis with the sample in flowing equimolar ethylene and hydrogen showed no variation in the apparent activation energy at temperatures up to 100 °C, confirming that the active sites remained intact at the higher temperatures. The results point to opportunities for overcoming the stability limitations of atomically dispersed supported noble metal catalysts by choice of electron‐donor supports and ionic liquid sheaths.

Kurtoğlu‐Öztulum, Samira F.↗
DOE OSTI2022

Atomically Dispersed Platinum in Surface and Subsurface Sites on MgO Have Contrasting Catalytic Properties for CO Oxidation

Atomically dispersed metals on metal oxide supports are a rapidly growing class of catalysts. Developing an understanding of where and how the metals are bonded to the supports is challenging because support surfaces are heterogeneous, and most reports lack a detailed consideration of these points. In this work, we report two atomically dispersed CO oxidation catalysts having markedly different metal–support interactions: platinum in the first layer of crystalline MgO powder and platinum in the second layer of this support. Structural models have been determined on the basis of data and computations, including those determined by extended X-ray absorption fine structure and X-ray absorption near edge structure spectroscopies, infrared spectroscopy of adsorbed CO, and scanning transmission electron microscopy. The data demonstrate the transformation of surface to subsurface platinum as the temperature of sample calcination increased. Catalyst performance data demonstrate the lower activity but greater stability of the subsurface platinum than of the surface platinum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Iridium pair sites anchored to Zr 6 O 8 nodes of the metal–organic framework UiO-66 catalyze ethylene hydrogenation

Isolated metal pair sites on metal oxide and zeolite supports are drawing attention as catalysts, because—in contrast to single atomically dispersed metals—they provide neighboring metal centers that can act cooperatively. We now report pairs of iridium atoms anchored to the Zr 6 O 8 nodes of the metal–organic framework (MOF) UiO-66, synthesized by chemisorption of Ir 2 (μ-OCH 3 ) 2 (COD) 2 (COD is cyclooctadienyl) followed by removal of the COD ligands. The supported species were characterized with infrared spectra of adsorbed CO combined with iridium LIII-edge extended X-ray absorption fine structure and high-energy-resolution fluorescence detection X-ray absorption near edge (HERFD XANES) spectra. The HERFD XANES spectra were recorded with the sample in a variety of atmospheres in which the iridium pair sites were stable, including CO, H 2 , and C 2 H 4 + H 2 at temperatures in the range of 35–80 °C. The data provide sensitive measures of the electronic structure of the iridium in the pair sites. The samples were evaluated as catalysts for ethylene hydrogenation, with the pair-sites being more selective for hydrogenation than analogous isolated atomically dispersed iridium, which catalyzes both hydrogenation and isomerization. Metal pair sites on MOFs offer uncharted opportunities for catalysts having reactivities associated with neighboring metal centers.

36 MATERIALS SCIENCE↗