Engineering topics

Garner, Charles E.

Publications and source records attributed to Garner, Charles E..

41 records · Page 3

NASA NTRS1989

Patterning of dispenser cathode surfaces to a controlled porosity

A process to pattern slots approximately 1.25 microns in width into 25-micron-thick W films that have been deposited onto flat or concave surfaces is discussed. A 25-micron-thick W film with a high degree of (100) orientation is chemically vapor deposited (CVD) onto a flat or concave Mo mandrel. A 5-micron-thick Al film is deposited onto the CVD W, followed by 2 microns of photoresist. On concave cathodes, XeCl2 laser ablation or X-ray lithography is used to pattern the photoresist, whereas on flat cathodes deep UV lithography can be used. The patterned photoresist serves as the mask in a Cl ion-beam-assisted etching (IBAE) process to pattern the Al. An alternative process is to deposit Al2O3 films onto the W and pattern the Al2O3 using laser ablation. The W film is then patterned to 3-6-micron slot widths using IBAE + ClF3 with the patterned Al or Al2O3 as the mask. Finally, a sputter deposition step is required to close up the slots to approximately 1 micron. The process described is capable of patterning concave dispenser cathodes to a controlled and precise porosity.

Garner, Charles E.↗

NASA NTRS1988

Ion propulsion system design and throttling strategies for planetary missions

This paper describes recent advances in ion propulsion system design which promise to increase the propulsion system reliability by reducing the overall system complexity. The greatest simplification in the overall propulsion system operation is accomplished through a change in the ion engine throttling strategy. By using three grid optics it is possible to effect engine throttling at a constant beam curent over at least a 3.8 to 1 variation in input power. Throttling at a constant beam current results in a single discharge chamber operating point and eliminates the need for active propellant flow controllers and complex engine throttling software. Detailed mission analysis calculations for a CNSR mission performed using this constant beam current throttling strategy indicate only a small reduction in delivered payload and increase in required propellant relative to a conventional throttling profile based on varying the beam curent.

Garner, Charles E.↗

NASA NTRS1988

Tests of high current hollow cathodes for ion engines

The development of high power, high thrust ion engines requires the development of long life hollow cathodes capable of producing emission currents of hundreds of amperes. This paper describes results obtained through the extended testing of two 12.7 mm diameter hollow cathodes at high emission currents. The first cathode, operated on xenon for a total of 170 hours at an emission current of 100 A, sustained very little damage except for an increase in the cathode orifice diameter, from 0.953 to 1.71 mm. The second cathode was operated on xenon at 150 A emission current continuously for 24 hours, and for over 1000 hours at 100 A on argon with essentially no change in the cathode operating characteristics. Operation of this cathode was terminated due to severe erosion of several discharge chamber components located downstream of the cathode. The erosion of these components occurred despite operation at discharge voltages less than 24 volts, and poses a serious challenge to the sucessful implementation of multi-hundred ampere cathodes and high thrust ion engines.

Brophy, John R.↗

NASA NTRS1987

Operating characteristics of a 10 kW xenon ion propulsion module

Performance testing of a two-engine functional model xenon ion propulsion module is described. Use of highly modified J-series 30 cm ion engines reconfigured for xenon propellant, a computer controlled operating system, and precise flow control system are shown to result in very reliable ion module operation at high input power levels. Ion engine operation at a nominal 4.0 ampere beam current and 30.0 volt discharge gives a specific impulse of 3310 sec, a total engine efficiency of 64.3 percent, and a thrust-to-power ratio of 39.5 mN/kW at an input power level of 5.10 kW. These modified J series ion engines are shown to be capable of throttling over an 8:1 range from a power level of 5.48 kW at 3285 sec to a power level of 0.70 kW at 1856 sec. In addition, complete ion engine performance mapping of important system level parameters such as thrust, specific impulse, efficiency and thrust-to-power ratio are presented.

Aston, Graeme↗

NASA NTRS1987

The effects of gas mixtures on ion engine erosion and performance

Erosion measurements were performed on a modified J-series 30 cm ion engine operating on xenon propellant. Erosion data was obtained by measuring the trench depth etched into masked polished metal samples for test durations of up to 24 hours. The data indicates that erosion is greatest at the cathode side of the baffle, with tantalum being the material with the least erosion of all materials tested. There is a clear indication of a significant reduction in erosion of all materials tested when nitrogen is added to the propellant. The technique used in these experiments requires test samples which are extremely smooth and flat.

Garner, Charles E.↗