Engineering topics
Publications and source records attributed to Galloway, T. L..
The service characteristics and changes affecting commuter airline operations are summarized. Community and passenger considerations are addressed and the benefits identified in NASA-sponsored aircraft studies are discussed.
An experimental investigation was conducted in the Ames 12-Foot Pressure Wind Tunnel to determine the unpowered aerodynamic characteristics of a 15-percent-scale model of a twin-engine commuter aircraft. Model longitudinal aerodynamic characteristics were examined at discrete flap deflections for various angle-of-attack and wind-tunnel-velocity ranges with the empennage on and off. Data are presented for the basic model configuration consisting of the fuselage, wing, basic wing leading edge, double slotted flaps, midengine nacelles, and empennage. Other configurations tested include a particle-span drooped leading edge (dropped outboard of the engine nacelles), a full-span drooped leading edge, low- and high-mounted engine nacelles, and a single-slotted flap. An evaluation was made of the model mounting system by comparing data obtained with the model mounted conventionally on the wind-tunnel model-support struts and the model inverted.
The results of contracted studies identifying the potential benefits of advanced technology are presented. Current in house studies and research efforts are discussed. An overview of the proposed technology elements in STAT research is presented.
Action to be taken to prepare to implement efficient, modern commuter aircraft for the 1990s is outlined. The increase in the contribution of jet fuel costs to aircraft direct operating costs (DOC) is noted as the motivation for the introduction of turboprop-powered commuter aircraft, which use 15-20% less fuel per seat mile at short stage lengths, to replace larger jet transports. Designs proposed by various manufacturers which will make use of existing technology for 19-, 30- and 50-seat aircraft capable of carrying a full payload of passengers and baggage for 600 n mi and optimized for minimum DOC over a 100-n mi stage length are presented, and the improvements in fuel usage, DOC and passenger comfort to be obtained with the use of advanced technology are pointed out. The goals and considered technologies of the dedicated small-transport aircraft technology program recommended by a commuter air transport subcommittee of the NASA Advisory Council Aeronautics Advisory Committee to speed the development of commuter technology are then presented, with attention given to efforts of analysis, design and testing of propulsion systems, structures, aerodynamics and systems intended to result in 16-24% savings in DOC and up to 40% savings in fuel. The commuter development plans of various manufacturers are also indicated.
The article surveys the results of the NASA-instituted Small Transport Aircraft Technology (STAT) research effort aimed at generating advanced technologies for application to new small, short haul transports having significantly better performance, efficiency, and environmental compatibility. Discussion covers fuselage designs and bonded aluminum-honeycomb wing construction which reduces the number of parts and fasteners, and gives a smoother outer contour. Topics discussed include: advanced aluminum alloys, composite primary structures, propellers, engine components, icing protection, avionics, flight controls, aerodynamics, and gust load alleviation.
This paper investigates the impact of configuration considerations, mission requirements, and performance constraints on conceptual commuter aircraft designs. Emphasis is placed on direct comparisons between turbofan and turboprop powered aircraft in the 10-30 passenger class. The analysis is accomplished using a computerized aircraft synthesis model that simulates the aircraft design and mission. The resulting conceptual aircraft are similar in size and performance regardless of engine type but the turboprop offers more mission flexibility
The short haul (less than 500 miles) passenger enplanements represent about 50% of the total domestic enplanements. These can be distinguished by the annual passenger flow for a given city pair and classified into low, medium and high densiy markets. NASA studies have investigated various advanced short haul aircraft concepts that have potential application in these three market areas. Although advanced operational techniques impact all market densities, advanced vehicle design concepts such as RTOL, STOL and VTOL have the largest impact in the high density markets. This paper summarizes the results of NASA sponsored high density short haul air transportation systems studies and briefly reviews NASA sponsored advanced VTOL conceptual aircraft design studies. Trends in vehicle characteristics and operational requirements will be indicated in addition to economic suitability and impact on the community.
Small communities are served by trunk, local-service, and commuter carriers having a wide variety in route structure, type of service, and economic character, operating over stage lengths less than 400 statute miles. NASA studies have investigated various aircraft concepts for short-haul that have potential in this market area. Aircraft concepts for this market require a careful balancing of performance, technology, and design-to-cost considerations. This paper summarizes some results of recent NASA sponsored air transportation system studies applicable to small community arenas.
Interactive computer graphics is a fast growing area of computer application, due to such factors as substantial cost reductions in hardware, general availability of software, and expanded data communication networks. In addition to allowing faster and more meaningful input/output, computer graphics permits the use of data in graphic form to carry out parametric studies for configuration selection and for assessing the impact of advanced technologies on general aviation designs. The incorporation of interactive computer graphics into a NASA developed general aviation synthesis program is described, and the potential uses of the synthesis program in preliminary design are demonstrated.
The potential of applying advanced technology to a single engine trainer configuration is investigated. The analysis is performed in a parametric manner to evaluate the individual and combined effects of various aerodynamic and propulsion technology considerations. The analysis is accomplished using a computerized aircraft synthesis model that simulates the aircraft design and mission. The resulting performance characteristics are compared with a current trainer design to identify the performance improvements or penalties.
Propulsion system and wing loading requirements are determined for a mechanical flap and an externally blown flap aircraft for various engine noise levels and two engine cycles. Both aircraft are sized to operate from a 914m (3000 ft) runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles - one having a fan pressure ratio of 1.5 and a bypass ratio of 9, and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust-to-weight ratio, wing loading, resulting gross weight, and direct operating costs, as functions of the engine noise level, for each combination of engine cycle and aircraft concept.
Short-haul transportation systems are characterized by low average utilization, high peak but low average passenger demand, severe competition from other transportation modes, high fixed costs and high operating costs. Studies were conducted to analyze the operational requirements and market size for medium-density air transportation. The determination of the aircraft that will most efficiently meet the requirements of this market requires the careful evaluation of variable parameters such as engine cycles, payload, field length range and type of high-lift system. Low noise, low cost and thrust reversing capability are the basic criteria for the propulsion system. It is concluded that aircraft of less than 50-seat capacity cannot generate satisfactory profits operating in the medium-density market.
The results of recent NASA-sponsored high-density and medium-density short-haul (less than 500 miles) air transportation systems studies are summarized. Trends in vehicle characteristics, in particular of RTOL and STOL concepts, are noted, and their economic suitability and impact on the community are examined.
The design requirements, performance, economics, and noise aspects of STOL and VTOL conceptual aircraft developed for short haul air transportation are reviewed, along with the characteristics of areas of high-density annual passenger flow in which the aircraft are intended to operate. It is shown that aircraft of 100 to 200 passenger capacity provide the best return on investment in high density markets. The various STOL propulsive lift concepts have the same general trends with field length; their wing loadings are 20 to 30 pounds per square foot higher than the nonpropulsive lift concepts. A comparison of the aircraft under consideration shows that no one aircraft concept will be optimum for all future operational environments.
The results of several NASA sponsored high density short haul air transportation systems studies are reported as well as analyzed. Included are the total STOL systems analysis approach, a companion STOL composites study conducted in conjunction with STOL systems studies, a STOL economic assessment study, an evaluation of STOL aircraft with and without externally blown flaps, an alternative STOL systems for the San Francisco Bay Area, and the quiet, clean experimental engine studies. Assumptions and results of these studies are summarized, their differences, analyzed, and the results compared with those in-house analyses performed by the Systems Studies Division of the NASA-Ames Research Center. Pertinent conclusions are developed and the more significant technology needs for the evaluation of a viable short haul transportation system are identified.
A method of propulsion system sizing for mechanical flap and externally blown flap aircraft is demonstrated. Included in this study is the effect of various levels of noise suppression on the aircraft final design characteristics. Both aircraft are sized to operate from a 3000-ft runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles - one having a fan pressure ratio of 1.5 and a bypass ratio of 9 and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust to weight ratio and wing loading and the resulting gross weight and direct operating costs as functions of the engine noise level for each of the four combinations of engine cycles and aircraft concepts.
A set of computer programs has been developed to estimate the takeoff and landing maneuver of a given aircraft. The program is applicable to conventional, vectored lift and powered-lift concept aircraft. Portions of the program may also be used to evaluate the static performance of these types of aircraft. The aircraft is treated as a point mass confined to motion in a vertical plane, and rotational dynamics have been neglected. The required input is described and a sample case is presented.
Continued growth of general-aviation over the next 10-15 years is dependent upon continuing improvement in aircraft safety, utility, performance, and cost. An attractive, compact, low-noise propulsor concept, the Q-FAN, when matched to reciprocating or rotary combustion engines, opens up the exciting prospect of new, cleaner airframe designs for the next generation of general-aviation aircraft, which will provide these improvements and meet the expected noise and pollution restrictions of the 1980 time period. In this paper, Q-FAN propulsion system performance, weight, noise, and cost trends are discussed. The impact of this propulsion system on the complete aircraft is investigated for two representative aircraft size categories. Examples of conceptual designs for Q-FAN/engine integration and aircraft installations are presented.