Engineering Papers⌕ Search

Engineering topics

Fuentes-Hernandez, Canek

Publications and source records attributed to Fuentes-Hernandez, Canek.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Inverted organic tandem solar cells with a charge recombination stack employing spatially confined p-type electrical doping

We report on the application of solution-based p-type electrical doping using 12-molybdophosphoric acid hydrate (PMA) to the fabrication of organic tandem solar cells. Such a doping approach leads to a spatially confined vertical doping profile down to a limited depth from the surface of polymer films, thus allowing the hole-collecting component of the charge recombination stack to be embedded in the photoactive layer of the bottom sub-cell. This simplifies the device architecture by removing the need for an extra dedicated hole-collecting layer. It is shown that this novel charge recombination stack comprising a PMA-doped bottom photoactive layer and a trilayer of Ag/AZO/PEIE is compatible with a solution-processed top photoactive layer. Here, the fabricated inverted organic tandem solar cells exhibit an open-circuit voltage that is close to the sum of the open-circuit voltages of the individual sub-cells, and a fill factor that is close to the better fill factor of the two sub-cells.

14 SOLAR ENERGY↗
DOE OSTI2022

An approach towards plastic scintillators from thermally activated delayed fluorescent dyes and cross-linkable bismuth compounds

Cross-linked polyvinyltoluene (PVT) based plastic scintillators loaded with dyes exhibiting thermally activated delayed fluorescence (TADF) and various amounts of (caproate)di-(methacrylate) bismuth (CMB) were developed. The co-polymerization of vinyl toluene monomer loaded with different weight ratios of CMB and 1 wt% of TADF dye yielded highly transparent cross-linked plastic scintillators with intense green photoluminescence. The thermal and mechanical properties of the scintillators were investigated using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and micro indentation techniques. Here, their performance for radiation detection was assessed by performing gamma spectroscopy using a Cs-137 source and benchmarked to commercial plastic scintillators. The loading of CMB was guided by Monte Carlo N-Particle (MCNP) simulations. The results of this study show that the cross-linking approach and the use of TADF dyes yield scintillators with good mechanical properties with a uniaxial yield strength up to ~66 MPa for compositions loaded with 40 wt% of CMB and high optical quality. However, the light yield in gamma spectroscopy experiments is found to be reduced with the addition of CMB, suggesting a trade-off between mechanical yield strength and light yield in gamma spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Extraction of intrinsic contact resistance in organic thin-film transistors with single channel length and high capacitance density

Accurate characterization of the intrinsic contact resistance is important for the optimization of organic thin-film transistors (OTFTs), especially in devices with high gate capacitance density. This study reports on a method for the extraction of the intrinsic, or gate-voltage independent, contact resistance from OTFTs. In contrast to the transfer length method (TLM), this method can be applied to devices with a single geometry. The method is an extension of the previously reported Y-function method and combines the model proposed by S. Luan et al. to analyze the effect of the gate voltage on the contact resistance. Here, this method is first applied to OTFTs with a bottom-gate top-contact geometry having varying gate capacitance density values. The intrinsic contact resistance is found to decrease with increased gate capacitance density with values ranging between 4 kΩcm and under 1 kΩcm when the gate capacitance is changed from 36.6 nF/cm 2 to 231.7 nF/cm 2 , respectively. These values are in good agreement with those obtained using TLM experiments. The new method is also shown to be applicable to OTFTs with top-gate bottom contact geometry.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Skin-like low-noise elastomeric organic photodiodes

Stretchable optoelectronics made of elastomeric semiconductors could enable the integration of intelligent systems with soft materials, such as those of the biological world. Organic semiconductors and photodiodes have been engineered to be elastomeric; however, for photodetector applications, it remains a challenge to identify an elastomeric bulk heterojunction (e-BHJ) photoactive layer that combines a low Young’s modulus and a high strain at break that yields organic photodiodes with low electronic noise values and high photodetector performance. Here, a blend of an elastomer, a donor-like polymer, and an acceptor-like molecule yields a skin-like e-BHJ with a Young’s modulus of a few megapascals, comparable to values of human tissues, and a high strain at break of 189%. Elastomeric organic photodiodes based on e-BHJ photoactive layers maintain low electronic noise current values in the tens of femtoamperes range and noise equivalent power values in the tens of picowatts range under at least 60% strain.

42 ENGINEERING↗
DOE OSTI2021

Increasing Volume in Conjugated Polymers to Facilitate Electrical Doping with Phosphomolybdic Acid

Molecular p-type electrical dopants have been proven useful to fine-tune the optoelectronic properties of bulk organic semiconductors and their interfaces. In this work, the volume in polymer films and its role in solution-based electrical p-type doping using phosphomolybdic acid (PMA) are studied. The polymer film volume was controlled using two approaches. One is based on heating both the PMA solution and the film prior to immersion. The second is based on coating the polymer film with a liquid blend that contains the PMA solution and a swelling solvent. 31 P NMR and FTIR experiments indicate that the Keggin structure appears to be preserved throughout the doping process. Results show that increasing the polymer volume facilitates the infiltration of the PMA Keggin structure, which results in an increased electrical p-type doping level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Benzocyclobutene polymer as an additive for a benzocyclobutene-fullerene: application in stable p–i–n perovskite solar cells

A poly(methacrylate) with benzocyclobutene side chains, CL, has been synthesized by radical polymerization for use as a crosslinking additive for a previously reported benzocyclobutene-functionalized fullerene, PCBCB, which can be thermally insolubilized following solution processing. Films of PCBCB incorporating CL and n-doped with (IrCp*Cp) 2 exhibit in-plane electrical conductivities around ten times higher than those of n-doped films without CL, while the use of CL also reduces leaching of dopant ions from the film upon washing. The performance and stability of perovskite solar cells using insolubilized PCBCB:CL, insolubilized PCBCB, or PCBM as top electron-extraction layers are compared; cells with undoped PCBCB:CL extraction layers exhibit higher average and maximum power conversion efficiencies (16 and 18.5%, respectively) than their PCBM and PCBCB counterparts. Devices with undoped PCBCB:CL extraction layers also showed excellent thermal stability, retaining 92% of their stabilized power output after aging for 3000 h at 85 °C in the dark in a nitrogen atmosphere.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Organic photodetector with built-in amplification for the detection of visible light with low optical power

We report on an organic-based photodetector that integrates a dual-gate organic thin-film transistor (DG-OTFT) with an organic photodiode (OPD) to produce a device with a high effective responsivity at low optical power and video-rate compatible response. In this device, the OPD operates in photovoltaic mode, instead of the commonly used photoconductive mode, to modulate one of the gate voltages of the DG-OTFT. Effective responsivity values of 10 A W –1 are measured at optical power values lower than 10 nW at 635 nm. Here, modeling of the operation of this new photodetector suggests that effective responsivity values up to 10 5 A W –1 can be achieved at optical powers of 1 nW using current printing technology and state-of-the-art organic semiconductors.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Large-area low-noise flexible organic photodiodes for detecting faint visible light

Silicon photodiodes are the foundation of light-detection technology; yet their rigid structure and limited area scaling at low cost hamper their use in several emerging applications. A detailed methodology for the characterization of organic photodiodes based on polymeric bulk heterojunctions reveals the influence that charge-collecting electrodes have on the electronic noise at low frequency. The performance of optimized organic photodiodes is found to rival that of low-noise silicon photodiodes in all metrics within the visible spectral range, except response time, which is still video-rate compatible. Solution-processed organic photodiodes offer several design opportunities exemplified in a biometric monitoring application that uses ring-shaped, large-area, flexible, organic photodiodes with silicon-level performance.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Effects of particle inclusions on cracking in ultrathin barrier films

Here, the effects of particle inclusions with different mechanical properties on the development of cracks in ultra-thin barrier films have been studied. Two types of particles, alumina and poly(styrene-b-methyl methacrylate) with large differences in their elastic modulus were used, representing both hard and soft inclusions. Particles were seeded onto polyethylene naphthalate substrates and subsequently coated with atomic layer deposited Al 2 O 3 as a barrier film. Ca corrosion tests used to determine the performance of the barrier films revealed that soft polymer particle inclusions severely affect the development of cracking in barrier films as compared to stiff ceramic particles. Tensile tests also confirmed that the barrier films with polymer particle inclusions have the lowest value of critical onset strain. Parametric simulations, conducted by varying the elastic modulus of the particle inclusions over a wide range, resulted in a larger strain energy release rate near particle inclusions which promotes crack formation and negatively impacts the performance of barrier films with softer particle inclusions. Thus, the combination of high residual stresses in the barrier films with the presence of soft particle inclusions is found the most detrimental for the development of high-performance ultrathin barrier films.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Organic thin-film transistors with a bottom bilayer gate dielectric having a low operating voltage and high operational stability

This study reports on p-channel bottom-gate organic thin-film transistors (OTFT) that achieve low-voltage operation with a thin bilayer gate dielectric of CYTOP/HfO 2 that also leads to high operational stability. A bottom-gate geometry allows the thickness of the gate dielectric to be reduced to 17 nm, thereby increasing the gate dielectric capacitance density to a value of up to 258 nF/cm 2 . All OTFTs yielded threshold voltages (V TH ) lower than -1 V, thereby providing minimum operating voltage (gate to source voltage ~ V TH ) of -1 V with field-effect mobility values in the range from 0.3 to 0.8 cm 2 /Vs and subthreshold swing values below 100 mV/dec. Operational stability during DC bias stress was found similar to that measured in devices with a top-gate geometry, with about 1% of drain current change after 6 h. Here, using a double-stretched exponential function, the operational stability characteristics were modeled. It was found that by increasing the metal oxide layer thickness, the threshold voltage can shift toward positive values under DC stress tests. For CYTOP layer thicknesses above 15 nm, a thicker CYTOP layer was found to shift the threshold voltage in the opposite direction toward negative values. Furthermore, these p-channel bottom-gate organic transistor with a bilayer gate dielectric of CYTOP/HfO 2 combine high mobility, high operational stability, and lower voltage operation of -1 V compared to top-gate OTFTs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impact of interface materials on side permeation in indirect encapsulation of organic electronics

This work demonstrates the impact of the contact interface between barrier films and adhesives on the side permeation of moisture into packaged devices. When barrier films are brought into contact with the adhesive layer during indirect encapsulation, permeation along defects at this interface can occur due to the imperfect nature of contact, resulting in the formation of pores. The connected network of pores can act as capillaries and be an alternative pathway for water permeation as opposed to the bulk of the adhesive or edge seal materials used for barrier attachment to the package. The rate of water permeation through the capillaries is governed by surface energies of the materials at the interfaces. Experimental results demonstrate that the rate of water permeation is significantly lowered by using materials with higher contact angles at the interface.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Host-Free Yellow-Green Organic Light-Emitting Diodes with External Quantum Efficiency over 20% Based on a Compound Exhibiting Thermally Activated Delayed Fluorescence

Thermally activated delayed fluorescent (TADF) materials are advantageous as emitters in organic light-emitting diodes (OLEDs) due to their ability to utilize all excited states formed by charge recombination for light emission, potentially leading to 100% internal quantum efficiency. As in conventional fluorescent or phosphorescent OLEDs, TADF emitters are commonly doped at a relatively low concentration in a host matrix. However, increasing evidence suggest that balanced ambipolar transport properties and small aggregation-induced fluorescence quenching allows TADF emitters to be used alone in so-called host-free OLEDs. Here, we report on host-free OLEDs in which the EMLs consist solely of a yellow-green-emitting TADF compound, 5,5'-(2,3,5,6-tetra(carbazol-9-yl)-1,4-phenylene)bis(2-(4-(tert-butyl)phenyl)-1,3,4-oxadiazole), TCZPBOX. Devices with this host-free EML yield a maximum external quantum efficiency (EQE) of 21%, current efficacy (CE) of 73 cd/A, and power efficacy (PE) of 79 lm/W at a luminance of 10 cd/m 2 . At a high luminance of 10,000 cd/m 2 , a high EQE of 13% is maintained. A maximum luminance of 120,000 cd/m2 is reached at an applied voltage of 9.8 V. When TCZPBOX was doped in the host of 2,6-di(carbazol-9-yl)-pyridine (PYD2) at 40 wt. %, the device yielded a maximum EQE of 28%, CE of 94 cd/A, and PE of 100 lm/W at 10 cd/m 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of the Number and Substitution Pattern of Carbazole Donors on the Singlet and Triplet State Energies in a Series of Carbazole-Oxadiazole Derivatives Exhibiting Thermally Activated Delayed Fluorescence

Substitution of a varying number of 9H-carbazole donors onto 2-(pentafluorophenyl)-5-phenyl-1,3,4-oxadiazole yields a series of donor–acceptor compounds with similar electrochemical band gaps, but dissimilar optical properties. Each substitution of a carbazole onto the 2- and 4-positions results in a 150–200 meV stabilization of the first singlet excited state, evident in the fluorescent emission. Here, the first triplet excited state is less sensitive to these substitutions, leading to a reduced energy separation between the singlet and triplet states, ΔE ST , with increasing carbazole content. OLED devices made using the donor–acceptor compounds exhibiting the lowest ΔE ST were fabricated and exhibit sky blue emission with an external quantum efficiency of up to 24.4% at a luminance of 10 cd m –2 , and 9.2% at 1000 cd m –2 .

36 MATERIALS SCIENCE↗
DOE OSTI2018

High performance blue-emitting organic light-emitting diodes from thermally activated delayed fluorescence: A guest/host ratio study

Emitters displaying thermally activated delayed fluorescence (TADF) can drive highly efficient organic light-emitting diodes (OLEDs). Such emitters are usually incorporated into the emissive layer (EML) at a relatively low concentration (<20 wt. %) with respect to a host material, a guest-host method inherited from conventional fluorescent or phosphorescent OLEDs. In this work, detailed studies on OLEDs, in which the concentration of oBFCzTrz (a blue-emitter displaying TADF) in a DPEPO host was varied from 8 to 100 wt. %, reveals that oBFCzTrz displays ambipolar transport and limited fluorescence-quenching due to aggregation. For instance, a neat film of oBFCzTrz maintains a photoluminescence quantum yield of 82%. We determine that OLEDs with an EML having an oBFCzTrz concentration of 50 wt. % in DPEPO yield a maximum external quantum efficiency (EQE) of 25.5% with an EQE roll-off of 10% in the range from 10 to 1000 cd/m 2 and Commission Internationale de l'Eclairage color coordinates of (0.20, 0.44). OLEDs with smaller or larger oBFCzTrz concentrations display smaller maximum EQE values. OLEDs with a neat oBFCzTrz EML display a maximum EQE of 14.0%. Finally, time-resolved electroluminescent decay studies, and analysis using a simple model, reveal significant differences in transport, trapping, and recombination in these devices.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Langmuir–Blodgett Thin Films of Diketopyrrolopyrrole-Based Amphiphiles

Here, we report on two π-conjugated donor–acceptor–donor (D–A–D) molecules of amphiphilic nature, aiming to promote intermolecular ordering and carrier mobility in organic electronic devices. Diketopyrrolopyrrole was selected as the acceptor moiety that was disubstituted with nonpolar and polar functional groups, thereby providing the amphiphilic structures. This structural design resulted in materials with a strong intermolecular order in the solid state, which was confirmed by differential scanning calorimetry and polarized optical microscopy. Langmuir–Blodgett (LB) films of ordered mono- and multilayers were transferred onto glass and silicon substrates, with layer quality, coverage, and intermolecular order controlled by layer compression pressure on the LB trough. Organic field-effect transistors and organic photovoltaics devices with active layers consisting of the amphiphilic conjugated D–A–D-type molecules were constructed to demonstrate that the LB technique is an effective layer-by-layer deposition approach to fabricate self-assembled, ordered thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Stable organic thin-film transistors

Organic thin-film transistors (OTFTs) can be fabricated at moderate temperatures and through cost-effective solution-based processes on a wide range of low-cost flexible and deformable substrates. Although the charge mobility of state-of-the-art OTFTs is superior to that of amorphous silicon and approaches that of amorphous oxide thin-film transistors (TFTs), their operational stability generally remains inferior and a point of concern for their commercial deployment. We report on an exhaustive characterization of OTFTs with an ultrathin bilayer gate dielectric comprising the amorphous fluoropolymer CYTOP and an Al2O3:HfO2 nanolaminate. Threshold voltage shifts measured at room temperatureovertimeperiods upto5.9×105 s do not vary monotonically and remain below 0.2 V in microcrystalline OTFTs (mc-OTFTs) with field-effect carrier mobility values up to 1.6 cm2 V-1 s-1. Modeling of these shifts as a function of time with a double stretched-exponential (DSE) function suggests that two compensating aging mechanisms are at play and responsible for this high stability. The measured threshold voltage shifts at temperatures up to 75°C represent at least a one-order-of-magnitude improvement in the operational stability over previous reports, bringing OTFT technologies to a performance level comparable to that reported in the scientific literature for other commercial TFTs technologies.

42 ENGINEERING↗