Engineering Papers⌕ Search

Engineering topics

Friese, Judah I

Publications and source records attributed to Friese, Judah I.

At least 19 records

Identifying and quantifying short-lived fission products from thermal fission of HEU using portable HPGe detectors

Due to the emerging potential for trafficking of special nuclear material, research programs are investigating current capabilities of commercially available portable gamma ray detection systems. Presented in this paper are the results of three different portable high-purity germanium (HPGe) detectors used to identify short-lived fission products generated from thermal neutron interrogation of small samples of highly enriched uranium. Samples were irradiated at the Washington State University (WSU) Nuclear Radiation Center’s 1MW TRIGA reactor. The three portable, HPGe detectors used were the ORTEC MicroDetective, the ORTEC Detective, and the Canberra Falcon. Canberra’s GENIE-2000 software was used to analyze the spectral data collected from each detector. Ultimately, these three portable detectors were able to identify a large range of fission products showing potential for material discrimination.

detectors↗

Design and Testing of a Boron Carbide Capsule for Spectral Tailoring in Mixed-Spectrum Reactors

A boron carbide capsule has been designed and used for spectral-tailoring experiments at the TRIGA reactor at Washington State University. Irradiations were conducted in pulsed mode and in continuous operation for up to 4 hours. A cadmium cover was used to reduce thermal heating. The neutron spectrum calculated with MCNP was found to be in good agreement with reactor dosimetry measurements using the STAY'SL computer code. The neutron spectrum resembles that of a fast reactor. Design of a capsule using boron carbide enriched in {sup 10}B shows that it is possible to produce a neutron spectrum similar to {sup 235}U fission.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Short-lived fission product measurements from >0.1 MeV neutron-induced fission using boron carbide.

A boron carbide shield was designed, custom fabricated, and used to create a fast fission energy neutron spectrum. The fissionable isotopes 233, 235, 238U, 237Np, and 239Pu were separately placed inside of this shield and irradiated under pulsed conditions at the Washington State University 1 MW TRIGA reactor. A unique set of fission product gamma spectra were collected at short times (4 minutes to 1 week) post-fission. Gamma spectra were collected on single-crystal high purity germanium detectors and on Pacific Northwest National Laboratory's (PNNL's) Direct Simultaneous Measurement (DSM) system composed of HPGe detectors connected in coincidence. This work defines the experimental methods used to produce and collect the gamma data, and demonstrates the validity of the measurements. It is important to fully document this information so the data can be used with high confidence for the advancement of nuclear science and non-proliferation applications. The gamma spectra collected in these and other experiments will be made publicly available at https://spcollab.pnl.gov/sites/gammadata or via the link at http://rdnsgroup.pnl.gov. A revised version of this publication will be posted with the data to make the experimental details available to those using the data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Investigation of Gravity Lanthanide Separation Chemistry

Lanthanides are common fission products and the ability to separate and quantify these elements is critical to rapid radiochemistry applications. Published lanthanide separations using Eichrom Ln Spec resin utilize an HCl gradient. Here it is shown that the efficacy and resolution of the separation is improved when a nitric acid gradient is used instead. The described method allows parallel processing of many samples in 1.5 hours followed by 60 minute counting for quantification of 9 isotopes of 7 lanthanide elements.

99 GENERAL AND MISCELLANEOUS↗

A Discussion of Procedures and Equipment for the Comprehensive Test Ban Treaty On-Site Inspection Environmental Sampling and Analysis

This paper is intended to serve as a scientific basis to start discussions of the available environmental sampling techniques and equipment that have been used in the past that could be considered for use within the context of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) on-site inspections (OSI). This work contains information on the techniques, equipment, costs, and some operational procedures associated with environmental sampling that have actually been used in the past by the United States for the detection of nuclear explosions. This paper also includes a discussion of issues, recommendations, and questions needing further study within the context of the sampling and analysis of aquatic materials, atmospheric gases, atmospheric particulates, vegetation, sediments and soils, fauna, and drill-back materials.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Isotopic Measurements: Interpretation and Implications of Plutonium Data

One of the fundamental activities within the field of nuclear forensics is the laboratory analysis of nuclear material; one aspect is providing the isotopic composition of the material under investigation. For both plutonium and uranium, this includes a unique suite of isotopes that, individually and collectively (i.e. an isotopic vector), will help characterize these materials, and potentially provide insight into their mode of production, intended utilization, and processing history. A full understanding of how this information is used provides the basis for defining the need for these measurements and helps determine the precision and accuracy requirements for those measurements. This paper provides an overview of this process as it applies to plutonium, discussing how reactor design and operating parameters can impact the resultant plutonium vector, thereby giving us the ability to infer those reactor traits based on isotopic measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nuclear Forensics: A Holistic Overview

Discussions of nuclear forensics are often restricted to work performed by radio-chemists measuring nuclear material attributes in the laboratory. However, this represents only one portion of the work required to answer critical questions. Laboratory analysis results in measurements that need to be evaluated. The results of those evaluations must be put into their proper context in order for them to be useful to others and often require merging those results with additional information. This may contribute to attribution, by virtue of inclusion or exclusion. Finally, the end product must be presented such that appropriate actions can be taken. This could include prosecution by law enforcement, policy initiatives on the part of legislative bodies, or military action in the case of nuclear attack (whether that attack is preempted or not). Using the discovery of a sample of plutonium during cleanup activities at Hanford in 2004, we will step through the process of discovery (representing an interdiction), initial field analysis, laboratory analysis, data evaluation and merging with additional data (similar to law enforcement and/or all source), thereby providing an example of an integrated approach.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complexation of Plutonium (IV) with Fluoride at Variable Temperatures

The complexation of Pu(IV) with fluoride at elevated temperatures was studied by solvent extraction technique. A solution of NaBrO3 was used as holding oxidant to maintain the oxidation state of plutonium throughout the experiments. The distribution ratio of Pu(IV) between the organic and aqueous phases was found to decrease as the concentrations of fluoride were increased. Stability constants of the 1:1 and 1:2 Pu(IV)-F- complexes, dominant in the aqueous phase under the experimental conditions, were calculated from the effect of fluoride ions on the distribution ratio. The thermodynamic parameters, including enthalpy and entropy of complexation between Pu(IV) and fluoride at 25 degrees C - 55 degrees C were calculated from the stability constants at different temperatures by using the Van’t Hoff equation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Bridging the Gap in the Chemical Thermodynamic Database for Nuclear Waste Repository: Studies of the Effect of Temperature on Actinide Complexation

Recent results of thermodynamic studies on the complexation of actinides (UO{sub 2}{sup 2+}, NpO{sub 2}{sup +} and Pu{sup 4+}) with F{sup -}, SO{sub 4}{sup 2-} and H{sub 2}PO{sub 4}{sup -}/HPO{sub 4}{sup 2-} at elevated temperatures are reviewed. The data indicate that, for all systems except the 1:1 complexation of Np(V) with HPO{sub 4}{sup 2-}, the complexation of actinides is enhanced by the increase in temperature. The enhancement is primarily due to the increase in the entropy term (T{Delta}S) that exceeds the increase in the enthalpy ({Delta}H) as the temperature is increased. These data bridge the gaps in the chemical thermodynamic database for nuclear waste repository where the temperature could remain significantly higher than 25 C for a long time after the closure of the repository.

54 ENVIRONMENTAL SCIENCES↗

Half-life and gamma abundance ratio measurements of Sm-153

The measurement of the decay of 153Sm was observed by gamma spectrometry, liquid scintillation counting and gas proportional counting in an attempt to confirm the half life and gamma abundance ratios for this isotope. Recent changes in the published nuclear decay data indicate that historical literature values may be biased. The 153Sm was made by the neutron activation of ultrapure isotopically enriched 152Sm to create 153Sm. The decay measurements were made over a three week period and no other isotopes were detected during this time. The gamma abundance ratio for the 103 keV gamma was measured to be (27.9%) which is 4% lower than the published data. In addition, the half life was 1.9308 days, which is 0.34% lower than the published data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Experimental Measurements of Short-Lived Fission Products from Uranium, Neptunium, Plutonium and Americium

Fission yields are especially well characterized for long-lived fission products. Modeling techniques incorporate numerous assumptions and can be used to deduce information about the distribution of short-lived fission products. This work is an attempt to gather experimental (model-independent) data on the short-lived fission products. Fissile isotopes of uranium, neptunium, plutonium and americium were irradiated under pulse conditions at the Washington State University 1 MW TRIGA reactor to achieve ~108 fissions. The samples were placed on a HPGe (high purity germanium) detector to begin counting in less than 3 minutes post irradiation. The samples were counted for various time intervals ranging from 5 minutes to 1 hour. The data was then analyzed to determine which radionuclides could be quantified and compared to the published fission yield data.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Separation and Quantification of Chemically Diverse Analytes in Neutron Irradiated Fissile Materials

Quantitative measurement of fission and activation products resulting from neutron irradiation of fissile materials is of interest for applications in environmental monitoring, nuclear waste management, and national security. To overcome mass and spectral interferences, and the relative small quantities of some target analytes, an extensive series of chemical separations is necessary. Based on established separations processes involving co-precipitation, solvent extraction, and ion-exchange and extraction chromatography, we have been evaluating and optimizing a proposed sequence of separation steps to allow for the timely quantification of analytes of interest. For simplicity, much of the chemical separation development work has been performed using stable elements as surrogates for the radioactive material. We have recently evaluated the optimized procedures using an irradiated sample to examine the adequacy of separations for measurement of desired analytes by gamma spectrometry. Here we present the results of this evaluation and describe the radiochemical separations utilized.

fission products↗

Neutron fluence and energy reproducibility of a 2-dollar TRIGA reactor Pulse

Washington State University’s 1 MW TRIGA reactor has a long history of utilization for neutron activation analysis (NAA). TRIGA reactors have the ability to pulse, reach supercritical (k>1) for short bursts of time. At this high power and fast time the energy spectrum and neutron fluence are largely uncharacterized. The pulse neutron energy spectrum and fluence were determined by the activation of Cu, Au, Co, Fe, and Ti. These analyses were completed with and without Cd shielding to determine reproducibility between pulses. The applications and implications of the neutron energy and fluence reproducibility to the use of pulsed NAA will be discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Complexation of Plutonium (IV) with Fluoride at Variable Tempeartures

Complexation of Pu(IV) with fluoride was studied by solvent extraction at 25, 40 and 55 C in 2.2 mol {center_dot} kg{sup -1} HClO{sub 4}. The distribution ratio of Pu(IV) between the organic and aqueous phases decreased as the concentration of fluoride was increased due to the formation of Pu(IV)-F complexes in the aqueous phase. Two complexes, PuF{sup 3+} and PuF{sub 2}{sup 2+}, were identified under the conditions in this work and their stability constants at 25, 40 and 55 C and I = 2.2 mol {center_dot} kg{sup -1} HClO{sub 4} were determined from the distribution data. The Specific Ion Interaction approach (SIT) was used to extrapolate the constants to the state of infinite dilution. Data from this work indicate that the complexation of Pu(IV) with fluoride is endothermic and entropy-driven. The complexation becomes stronger at higher temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermodynamics of Neptunium (V) Complexes with Phosphate at Elevated Temperatures

Abstract – The complexation of Np(V) with phosphate at elevated temperatures was studied by a synergistic extraction method. A mixed buffer solution of TRIS and MES was used to maintain an appropriate pH value during the distribution experiments. The distribution ratio of Np(V) between the organic and aqueous phases was found to decrease as the concentrations of phosphate were increased. Stability constants of the 1:1 and 1:2 Np(V)-HPO42- complexes, dominant in the aqueous phase under the experimental conditions, were calculated from the effect of [HPO42-] on the distribution ratio. The thermodynamic parameters including enthalpy and entropy of complexation between Np(V) and HPO42- at 25o C – 55o C were calculated by the temperature coefficient method.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Spectrophotometric and calorimetric studies of Np(V)complexation with sulfate at 10-70A degrees c

One of the approaches to safe management of highlevel nuclear wastes (HLW)calls for the disposal of HLW in geological repositories. Though the engineered barrier systems are expected to last a very long time after the repository is closed, they may gradually deteriorate and eventually lose integrity. consequently, water could contact the waste, dissolve it, and carry radionuclides out of the repository. Under the chemical environment in the vicinity of the waste form, 237Np(V) is one of the most soluble radionuclides and is most likely to be carried away from the repository. Because of its long half-life and high mobility, it is projected that, in the proposed Yucca Mountain Repository, the fractional dose attributed to 237Np will increase to 67% of the total dose in 75000 years [1]. As a result, the migration of Np in the postclosure chemical environment of the repository is a great concern to long-term repository performance. Because the temperature of the HLW repository could remain significantly higher than the ambient even thousands of years after the closure of the repository, predictions of the chemical behavior of Np in the repository can not be made without reliable thermodynamic data concerning the interactions of Np with the ligands that exist in the groundwater of the repository (e.g., OH–, F–, SO42– , PO43– and CO32) at elevated temperatures. Unfortunately, thermodynamic data on actinide complexation at elevated temperatures are scarce and highly scattered [2]. Lack of reliable geochemical thermodynamic data could lead to conservative decisions that have too big safety margins and raise the cost of the project. To help with the performance assessment of the HLW repository and fill the gap in thermodynamic data on actinide complexation at elevated temperatures, we have studied the complexation of actinides (Th, U, Np and Pu) with selected organic and inorganic ligands at elevated temperatures. This paper summarizes the results of the complexation of Np(V) with sulfate at 10–70°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complexation of neptunium(V) with fluoride in aqueous solutions at elevated temperatures

Over the past several decades, the production and testing of nuclear weapons in the U.S. have created significant amounts of high-level nuclear wastes (HLW) that are currently stored in underground tanks across the U.S. DOE (Department of Energy) sites. Eventually, the HLW will be made into the waste form and disposed of in geological repositories for HLW. Among the radioactive materials, neptunium is of great concern in the post-closure chemical environment in the repository because of the long half-life of 237Np (2.14•106 years) and the high mobility of Np(V), the most stable oxidation state of neptunium. It is estimated that 237Np, together with 129I and 99Tc, will be the major contributors to the potential total annual dose from the repository beyond 10000 years [1]. Due to the high radiation energy released from the HLW, the postclosure repository is expected to remain at elevated temperatures for thousands of years [1]. If the waste package is breached and becomes in contact with groundwater, neptunium, as well as other radioactive materials will be in aqueous solutions at elevated temperatures. Interactions of radioactive materials with the chemical components in groundwater play an important role in determining their migration in the repository. To predict the migration behavior of neptunium, it is necessary to have sufficient and reliable thermodynamic data on its complexation with the ligands that are present in the groundwater of the repository (e.g., OH–, F–, SO42– ,PO43– and CO32) at elevated temperatures. However, such data are scarce and scattered for 25°C, and nearly nonexistent for elevated temperatures [2]. To provide reliable thermodynamic data, we have conducted investigations of the complexation of actinides, including thorium, uranium, neptunium and plutonium, at elevated temperatures. Thermodynamic parameters, including formation constants, enthalpy and heat capacity of complexation are experimentally determined. This paper summarizes the results of the complexation of Np(V) with fluoride in aqueous solutions at 10–70°C studied by spectrophotometry and microcalorimetry.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Spectrophotometric and Calorimetric Studies of Np(V) Complexation with Sulfate at 10-70oC

Sulfate, one of the inorganic constituents in the groundwater of nuclear waste repository, could affect the migration of radioactive materials by forming complexes. Spectrophotometric and microcalorimetric titrations were performed to identify the Np(V)/sulfate complex and determine the equilibrium constants and enthalpy of complexation at 10-70 C. Results show that the complexation of Np(V) with sulfate is weak but slightly enhanced by the increase in temperature. The complexation is endothermic and becomes more endothermic with the increase in temperature. The enhanced complexation at elevated temperatures is due to the increasingly larger entropy of complexation that exceeds the increase in enthalpy, suggesting that the complexation of Np(V) with sulfate is entropy-driven.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗