Engineering topics

Frankel Lyons

Publications and source records attributed to Frankel Lyons.

5 records

NASA NTRSDate not supplied

Alternative MMOD Shielding Concepts

The main types of meteoroid and orbital debris (MMOD) shields are single-layer “monolithic” shields, dual-wall “Whipple” shields, and multi-wall shields (“Stuffed Whipple” and “multi-shock” are common types). Aluminum alloys are typically used for the outer bumper layer and for the rear wall of the dual- and multi-wall shields, although carbon-composites are increasingly employed in MMOD shields given their low-mass and high-strength. Ceramic (NextelTM) and KevlarTM fabrics are commonly used for the intermediate layers of Stuffed Whipple shields. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) group is continuously working to improve NASA spacecraft MMOD shielding by evaluating new materials and shielding concepts by test and analysis. HVIT has performed many hypervelocity impact tests over several years to evaluate alternative MMOD shield materials and concepts. This paper will provide results of this work in the following areas: (1) Material substitutions to improve radiation and MMOD protection within Stuffed Whipple shields, (2) Metallic and ceramic foam bumper and intermediate layer materials, (3) Self-sealing materials. In the first two areas listed above, the candidate shield materials were tested under similar test conditions and with fixed shield standoff and mass. Damage to the rear wall was quantified and compared to determine the best performing shield materials. In the self-sealing material evaluations, the test objective was to gauge the ability of different materials and techniques to stop leaks in a rear wall with a 1-atmosphere (air) delta-pressure across the wall. This paper provides results of the investigations and describes forward work to continue the development of the most promising MMOD shield alternatives. KevlarTM is a trademark of DuPont de Nemours, Inc. NextelTM is a trademark of 3M Corporation Note, Trade names and trademarks are used in this report for identification only. Their usage does not constitute an official endorsement, either expressed or implied, by the National Aeronautics and Space Administration.

Hypervelocity↗

NASA NTRSDate not supplied

The NASA JSC Hypervelocity Impact Technology (HVIT) Office

The Hypervelocity Impact Technology (HVIT) office at the National Aeronautical and Space Administration (NASA) Johnson Space Center (JSC) is dedicated to support NASA flight programs in meeting their meteoroid and orbital debris (MMOD) protection requirements both efficiently and effectively, with a minimum of shielding mass, volume, and cost. This paper provides an overview of HVIT capabilities in providing hypervelocity tests, analyses, MMOD risk assessments and shielding expertise. HVIT personnel work closely with NASA program and safety/mission assurance personnel to develop program-specific MMOD protection requirements which are both achievable based on initial risk assessments and will meet overall safety and mission success requirements. HVIT then proceeds with hypervelocity impact testing and hydrocode assessments to update and verify ballistic limit equations used in the MMOD risk assessment. Hypervelocity impact tests are primarily performed at the NASA WSTF Remote Hypervelocity Test Laboratory (RHTL). Other hypervelocity facilities that provide complementary test capabilities are called on when necessary to fill data gaps. The goal of the final pre-flight MMOD risk assessment is to show compliance with MMOD requirements prior to flight. This final assessment will also incorporate changes in the MMOD environment from meteoroid showers and orbital debris breakups. After the mission is flown, post-flight inspections are performed by HVIT to document and trend MMOD damage to returned spacecraft surfaces and hardware. HVIT accomplishments in NASA mission support are described. In addition, current HVIT activities to aid on-going NASA crewed missions and science missions are presented.

Meteoroid↗

NASA NTRSDate not supplied

The NASA JSC Hypervelocity Impact Technology (HVIT) Office

- HVIT’s operational objectives for NASA, commercial, and international partners are to 1) help to define MMOD risk requirements 2) provide assessments that identify risk drivers for a specific spacecraft design, and 3) work to design and optimize shielding technologies based on increasing performance and reducing mass. - The use of Bumper-code underpins all risk assessments provided by HVIT – by using a complete FEM model, Bumper can provide a wholistic view of risk for a given design and mission profile. - A full risk assessment, however, requires an iterative approach, where Bumper is first used to identify potential risk drivers. Subsequent analysis can focus on iterating the shield design in highest risk areas. And may include the refinement of BLEs through testing, design modification, or reexamination of the failure criteria. - HVIT utilizes a wide-range of expertise to provide the most accurate risk assessments possible – areas of active research are highlighted below.

hypervelocity impact↗

NASA NTRSDate not supplied

Alternative MMOD Shielding Concepts

A core objective of the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) group is to improve spacecraft meteoroid and orbital debris (MMOD) shielding by evaluating new materials and shielding concepts by test and analysis. This paper describes hypervelocity impact tests that were performed over several years to evaluate alternative MMOD shielding concepts. Specific objectives of the work were to incorporate improved MMOD and radiation protection within Stuffed Whipple shields, and to evaluate various self-sealing MMOD shielding concepts. The tests were performed under similar impact conditions and with fixed shield standoff and comparable overall shield mass. Damage to the rear wall was quantified and compared to determine the best performing shield concepts. Generally, the best shielding for both MMOD and radiation protection included polymer materials rich in hydrogen introduced into the intermediate and final layers of the shielding. In the self-sealing material evaluations, the test objective was to gauge the ability of different materials and techniques to stop leaks in a rear wall with a delta-pressure across the wall typical of spacecraft crew cabins (i.e., up to 1 atmosphere pressure). Shielding containing ionomer films and elastomer materials satisfied this objective for pressure shell holes up to 6mm diameter. This paper provides results of the investigations.

Orbital Debris↗

NASA NTRSDate not supplied

Risks from Small Orbital Debris

This talk provides evidence that the threat to mission success from millimeter sized debris is a legitimate concern by considering (1) on-orbit impact data, (2) hypervelocity tests on spacecraft systems, (3) risk assessments for ISS and satellites.

Orbital Debris↗