Engineering topics
Publications and source records attributed to Foughner, J. T., Jr..
Vortex modeling techniques and experimental studies of research configurations utilizing vortex flows are discussed. Also discussed are vortex flap investigations using generic and airplane research models and vortex flap theoretical analysis and design studies.
A series of pivotable strakes have been tested in combination with a 44-deg swept wing to determine their ability to provide pitch control at high angles of attack. The tests were carried out in the Langley 7 X 10-Foot High-Speed tunnel at nominal Mach numbers of 0.3 to 0.4. A total of five strakes with various aspects ratios and shapes were tested at negative deflection angles of 5, 10, 15, and 20 deg through an angle of attack range up to approximately 50 deg. In addition, a cranked delta wing with 70-deg sweep was tested with two different pivotable apex flaps. This paper shows lift, drag and moment data for the complete configurations as well as for the separate contributions of the strakes and fuselage nose which are mounted on a second balance. Generally, strake deflection was found to have a significant effect on moment while lift/drag changed very little.
The need for flow visualization and laser velocimetry were discussed. The purpose was threefold: (1) provide a state-of-the-art overview; (2) provide a forum for industry, universities, and government agencies to address problems in developing useful and productive flow visualization and laser velocimetry measurement techniques; and (3) provide discussion of recent developments and applications of flow visualization and laser velocimetry measurement techniques and instrumentation systems for wind tunnels including the 0.3-Meter Transonic Cryogenic Tunnel.
Results are presented for a passive flutter suppression approach known as the decoupler pylon. The decoupler pylon dynamically isolates the wing from store pitch inertia effects by means of soft spring/damper elements assisted by a low frequency feedback control system which minimizes static pitch deflections of the store because of maneuvers and changing flight conditions. Wind tunnel tests and analyses show that this relatively simple pylon suspension system provides substantial increases in flutter speed and reduces the sensitivity of flutter to changes in store inertia and center of gravity. Flutter characteristics of F-16 and YF-17 flutter models equipped with decoupler pylon mounted stores are presented and compared with results obtained on the same model configuration with active flutter suppression systems. These studies show both passive and active concepts to be effective in suppressing wing/store flutter. Also presented are data showing the influence of pylon stiffness nonlinearities on wing/store flutter.
Passive flutter-suppression system has been developed to increase flutter speed of aircraft wings that are adversely affected by addition of large masses (stores) to the wings, such as external fuel tanks. Important features of system are its effectiveness for large variations in mass of store as well as unsensitivity of system to large change in location of store center-of-gravity.
This paper presents results for a passive flutter suppression approach known as the decoupler pylon. The decoupler pylon dynamically isolates the wing from store pitch inertia effects by means of soft-spring/damper elements assisted by a low-frequency feedback-control system which minimizes static pitch deflections of the store due to maneuvers and changing flight conditions. Wind-tunnel tests and analyses show that this relatively simple pylon suspension system provides substantial increases in flutter speed and reduces the sensitivity of flutter to changes in store inertia and center-of-gravity location. Flutter characteristics of F-16 and YF-17 flutter models equipped with decoupler pylon-mount stores are presented and compared with results obtained on the same model configurations using active flutter suppression systems. These studies show both passive and active concepts to be effective in suppressing wing/store flutter. Also presented are data showing the influence of pylon stiffness nonlinearities on wing/store flutter.
Six experimental investigations conducted in the transonic dynamics tunnel, which supported elements of the entry and the landed phases of the Viking mission, are described. The objective of each investigation and selected experimental results are presented. How these particular wind tunnel results contributed to spacecraft development and ultimately to the success of the Viking mission is indicated. Experimental studies applicable to the entry phase of the mission included parachute environment and performance definition, aerodynamic characteristics exhibited by two separating bodies, and pressure measurements in the transonic range to optimize the location and orientation of a stagnation-pressure sensor on the Lander. The experimental investigations which supported the landed phase of the mission included a convective heat transfer test to establish the requirements for wind covers for the radioisotope thermoelectric generators and two tests which supported the development and calibration of the meteorological science experiment.
As an alternative to alleviating wing/store flutter by conventional passive methods or by more advanced active control methods, a quasi-passive concept, referred to as the decoupler pylon, is investigated which combines desirable features of both methods. Passive soft-spring/damper elements are used to decouple wing modes from store pitch modes, and a low-power control system maintains store alignment under changing mean loads. It is shown by analysis and wind tunnel tests that the decoupler pylon provides substantial increase in flutter speed and makes flutter virtually insensitive to inertia and center-of-gravity location of the store.
Results from transonic flutter model studies are presented. The flutter model was constructed to support the flutter prevention and clearance program from preliminary design through flight flutter tests. The model tests were conducted in the Langley transonic dynamics tunnel. The large full span free-flying model was shown to be an effective tool in defining airplane flutter characteristics by demonstrating freedom from flutter for most configurations and by defining optimum solutions for a few troublesome configurations.
The flutter prevention and clearance task for the F-16 airplane is being accomplished in a combined analysis, wind-tunnel dynamic model test, and flight flutter test program. This paper presents highlight results from transonic flutter model studies. The flutter model was constructed to support the flutter prevention and clearance program from preliminary design through flight flutter tests. The model tests were conducted in NASA's Langley Transonic Dynamics Tunnel. The large full-span free-flying model is shown to be an effective tool in defining airplane flutter characteristics by demonstrating freedom from flutter for most configurations and by defining optimum solutions for a few troublesome configurations.
Wind-tunnel tests have been made in the Langley transonic dynamics tunnel on a 0.25-scale model of Sandia Laboratories' 3.96-meter (13-foot), slanted ribbon design, lifting parachute. The lifting parachute is the first stage of a proposed two-stage payload delivery system. The lifting parachute model was attached to a forebody representing the payload. The forebody was designed and installed in the test section in a manner which allowed rotational freedom about the pitch and yaw axes. Values of parachute axial force coefficient, rolling moment coefficient, and payload trim angles in pitch and yaw are presented through the transonic speed range. Data are presented for the parachute in both the reefed and full open conditions. Time history records of lifting parachute deployment and disreefing tests are included.
Experiences obtained with four methods of predicting flutter of wind-tunnel models from subcritical response data are described. The four methods are: co/quad, randomdec, power spectra density, and the peak-hold spectrum. Model excitation techniques included both forced (sinusoidal sweep) and random (tunnel turbulence). These methods were successfully used to measure the frequency and damping (or an inverse response amplitude proportional to the damping) in the predominant flutter modes. Implementation and application of each method are discussed. Some results and comparisons between methods are presented.
A wind tunnel test has been conducted on one-eighth scale models of the Space Shuttle Solid Rocket Booster drogue parachute system. The test included an investigation of four candidate drogue deployment concepts and a parametric steady state drag study of 20-degree conical ribbon parachutes. The results show that at least two of the four deployment concepts tested are viable candidates for the full scale deployment system. The interference free steady state drag results obtained show excellent agreement with available drop test results on large 20-degree conical ribbon parachutes.
Transonic wind-tunnel studies were conducted with modified cross, hemisflo, and disk-gap-band parachute models in the wake of a cone-cylinder shape forebody. The basic cross design was modified with the addition of a circumferential constraining band at the lower edge of the canopy panels. The tests covered a Mach number range of 0.3 to 1.2 and a dynamic pressure range from 479 Newtons per square meter to 5746 Newtons per square meter. The parachute models were flexible textile-type structures and were tethered to a rigid forebody with a single flexible riser. Different size models of the modified cross and disk-gap-band canopies were tested to evaluate scale effects. Model reference diameters were 0.30, 0.61, and 1.07 meters (1.0, 2.0, and 3.5 ft) for the modified cross; and nominal diameters of 0.25 and 0.52 meter (0.83 and 1.7 ft) for the disk-gap-band; and 0.55 meter (1.8 ft) for the hemisflo. Reefing information is presented for the 0.61-meter-diameter cross and the 0.52-meter-diameter disk-gap-band. Results are presented in the form of the variation of steady-state average drag coefficient with Mach number. General stability characteristics of each parachute are discussed. Included are comments on canopy coning, spinning, and fluttering motions.
The results of wind tunnel tests of three parachute configurations in the wake of a cone-cylinder are presented. The tests were conducted to extend the drag and stability characteristics of selected parachutes through the transonic speed range. The configurations studied were the hemisflo ribbon, the cross, and the disk-gap-band types. The results are presented as the variation of the parachute drag coefficient with Mach number. General stability characteristics of the parachutes are discussed. The results are then correlated with some published subsonic and supersonic data.
Results are presented from a wind-tunnel investigation of the flow field around a 0.45-scale model of a Mars lander. The tests were conducted in air at values of Reynolds number equivalent to those anticipated on Mars. The effects of Reynolds number equivalent to those anticipated on Mars. The effects of Reynolds number, model orientation with respect to the airstream, and the position of a dish-type antenna on the flow field were determined. An appendix is included which describes the calibration and operational characteristics of hot-film anemometers under simulated Mars surface conditions.
Studying ground-wind loads with models of space shuttle configurations to assess aerodynamic instabilities on erected space shuttle vehicles
Drag sphere anemometers for ground wind velocity measurements and spacial correlation of gusts