Engineering topics
Publications and source records attributed to Fitzgerald, D. J..
An energy analyzer has been constructed that is appropriate for measuring the energy profile and charge state distribution of the exhaust plume of a xenon-driven Hall thruster.
Amorphous iron and titanium-based alloys containing various amounts of chromium, phosphorus, and boron exhibit high corrosion resistance. Some physical properties of Fe and Ti-based metallic alloy films deposited on a glass substrate by a dc-magnetron sputtering technique are reported. The films were characterized using differential scanning calorimetry, stress analysis, SEM, XRD, SIMS, electron microprobe, and potentiodynamic polarization techniques.
Lower temperatures result in higher purity and fewer equipment problems. In cluster-beam deposition, clusters of atoms formed by adiabatic expansion nozzle and with proper nozzle design, expanding vapor cools sufficiently to become supersaturated and form clusters of material deposited. Clusters are ionized and accelerated in electric field and then impacted on substrate where films form. Improved cluster-beam technique useful for deposition of refractory metals.
Experiments point way toward more relaxed controls over ion-implanation dosage and uniformity in solar-cell fabrication. Data indicate cell performance, measured by output current density at fixed voltage, virtually same whether implant is particular ion species or broad-beam mixture of several species.
New cathode has form of hollow tube through which gas enters region of high electron density, produced by electric discharge with auxiliary electrode referred to as "keeper." Ion-gun cathode emits electrons that bombard gas in chamber. Ions accelerated out of source are used to dope semiconductor material.
Biasing techniques and their application to the control of spacecraft potential is discussed. Normally when a spacecraft is operated with ion thrusters, the spacecraft will be 10-20 volts negative of the surrounding plasma. This will affect scientific measurements and will allow ions from the charge-exchange plasma to bombard the spacecraft surfaces with a few tens of volts of energy. This condition may not be tolerable. A proper bias system is described that can bring the spacecraft to or near the potential of the surrounding plasma.
An igniter for the air/fuel mixture used in the cylinders of an internal combustion engine is described. A conventional spark is used to initiate the discharge of a large amount of energy stored in a capacitor. A high current discharge of the energy in the capacitor switched on by a spark discharge produces a plasma and a magnetic field. The resultant combined electromagnetic current and magnetic field force accelerates the plasma deep into the combustion chamber thereby providing an improved ignition of the air/fuel mixture in the chamber.
Hot ionized gas (plasma) ignites air/fuel mixture in internal combustion engines more effectively than spark. Electromagnetic forces propel plasma into combustion zone. Combustion rate is not limited by flame-front speed.
Interactive effects between ion engine thrust beams and an SEP spacecraft and its science payload have been examined. AC electric contamination from thrust beam potential fluctuations of both 'common mode' and 'point-to-point' forms has been evaluated. Quenching of point-to-point E-fields by both thrust ion and charge exchange ion plasmas is expected. Reduction methods for AC electric contamination from common mode thrust beam potential fluctuations have been developed. Charged particle contamination of ambient space and plasma wave contamination may result from density magnitude and spatial extent of charge exchange plasma plumes. Reduction methods for cone of directions of high angle charge exchange ions have been examined.
Charge build-up on spacecraft surfaces and resulting zones of electrostatic contamination have been examined for electrically active and electrically passive spacecraft with both conducting and dielectric surface materials, illuminated and nonilluminated surface conditions, and for both inclusion and neglect of free charge effects from photocurrents and ambient space plasma particles. Techniques for measurement and reduction of electrostatic contamination zone extent have been developed for spacecraft with charge release capability. Indicated limitations for contamination cleanup are about 1 volt potential variation from spacecraft to ambient plasma. Bandwidths of electrostatic monitoring and clamping devices extend to several hundred kilohertz for both DC and 'broadband' AC electrostatic cleanliness.
An analysis has been performed which describes the electrical interactions between simultaneously operating ion thrusters and between the ion thrusters and a spacecraft bus. The problem is reduced to a relatively simple equivalent circuit including all leakage paths. The influence of the various circuits elements on a spacecraft potential is studied. A thruster grounding scheme is introduced which is designed to minimize the electrical interactions and includes protection for both thrusters and spacecraft from possible damage due to neutralizer failure. The paper includes the results of various experiments which have been conducted to quantitatively define the elements of the equivalent circuit.
An ion thruster is described in which the cathode front end, surrounded by our insulator, is mounted flush with the front end of the flanged portion of the cathode pole piece. The thruster's baffle positioned in front of the cathode's front end supports the thruster's keeper electrode which is space apart and directed to the cathode's open end. The baffle is at the keeper's electrode potential.
The calibration of a typical 20-cm diameter ion thrustor was examined to determine performance penalties that must be assessed in projecting measured performance into a space environment. Four specific areas were investigated. These include (1) double ion content of the beam, (2) back ingestion from the vacuum facility, (3) beam spreading, and (4) propellant flow rate measurements. The double ion content was measured and found to be as high as 5.5% at an arc voltage of 35 volts. Back ingestion was observed to become significant above tank pressures of 6 microtorr. Beam spreading reduced effective thrust on the order of 2.5%.
A parametric investigation of mercury hollow cathode neutralizers was carried out in a bell jar over a range in bias currents up to 2 A. The parameters of particular interest were the mercury flowrate, the bias voltage, and the neutralizer cathode temperature. Three cathode orifices and several keeper geometries were tested. The bell jar tests compared well with neutralizer run with active thrusters. The effects of these parameters on the neutralizer stability and lifetime capability as well as the effects on the total thrust subsystem efficiency are discussed.
Electron bombardment ion thrustor using hollow cathode and two-grid ion accelerating geometry, discussing performance tests
Mercury electron bombardment thrustor, measuring effect of geometry and magnetic field inside pole piece region on discharge losses and propulsion efficiency