Engineering Papers⌕ Search

Engineering topics

Fensin, S. J.

Publications and source records attributed to Fensin, S. J..

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗

Spall and subsequent recompaction of copper under shock loading

Research was undertaken to study spall and subsequent recompaction of oxygen-free high-thermal-conductivity copper using a single-stage large-bore light gas gun capable of planar impacts. Gun experiments were conducted that produced an initial spall in the target with a subsequent recompaction of the spall damage/layer by the use of layered impactors. Symmetric spall experiments at similar conditions were also conducted as a control to the recompaction experiments. Photonic Doppler velocimetry was used to obtain the velocity history of the target’s back surface; these velocity histories were analyzed, and the results were compared to numerical simulations. After recovery of selected samples, the microstructure was analyzed using optical imaging microscopy and electron backscatter diffraction. Recompaction waves were clearly observed in the time-resolved data obtained at the back surface of the targets. Two different series of experiments were performed to understand the effect of damage morphology on the stress required for spall recompaction. In the initial series, the peak pressure of the first shock was systematically increased to alter the amount of damage in the material. While in the second series, the peak pressure of the second shock was increased, keeping the magnitude of the first shock relatively constant to understand the effect of peak stress on the recompaction process. Findings clearly show that recompaction results in a perturbed band of the microstructure at the location of the expected spall plane in all cases except where the peak stress of the second shock is lower than the critical value.

, recompaction↗

Anisotropic shock response of single-crystalline β-phase tin shock physics, molecular dynamics, plasticity

Mesoscale simulations of the dynamic response of polycrystalline metals to shockwave compression can provide unique insight in to the nature of the various physical mechanisms responsible for material failure. This approach requires a constitutive description for individual grains and boundaries, including defects such as dislocations, within an explicit representation of the microstructure geometry and evolving deformation fields. Computational models of the single-crystal constituents cannot be unambiguously constrained by traditional measurements of the shock or stress-strain response of polycrystalline metals. Instead, these models require comprehensive measurements of the anisotropic shock response of single crystals for their calibration and validation. We present a coordinated experimental and simulation campaign on the shock response of single-crystalline β-phase tin demonstrating a remarkable anisotropic elastic-plastic response of the metal. This anisotropy will be explained with the help of molecular dynamics simulations that show preferred twinning in one orientation.

36 MATERIALS SCIENCE↗

Spall response of single-crystal copper

We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 10 6 s -1 and peak shock stresses in the 5–14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.

36 MATERIALS SCIENCE↗

Structure/property (constitutive and spallation response) of additively manufactured 316L stainless steel

For additive manufacturing (AM) of metallic materials, the certification and qualification paradigm needs to evolve as there is currently no broadly accepted “ASTM- or DIN-type” additive manufacturing certification process or AM-produced material specifications. Accordingly, design, manufacture, and subsequent implementation and insertion of AM materials to meet engineering applications requires detailed quantification of the constitutive (strength and damage) properties of these evolving materials, across the spectrum of metallic AM methods, in comparison/contrast to conventionally-manufactured metals and alloys. For this paper, cylindrical samples of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1 kW Yb-fiber laser. The microstructure of the AM-316L SS was characterized in both the “as-built” AM state and following a heat-treatment designed to obtain full recrystallization to facilitate comparison with annealed wrought 316L SS. The constitutive behavior as a function of strain rate and temperature was characterized and is compared to that of annealed wrought 316L SS plate material. The dynamic shock-loading-induced damage evolution and failure response of all three 316L SS materials was quantified using flyer-plate impact driven spallation experiments at peak stresses of 4.7 and 6.5 GPa. The spall strength of AM-produced 316L SS and the recrystallized-AM-316L SS were found to decrease with increasing peak shock stress while the annealed wrought 316L SS spall strength remained essentially constant. Finally, the damage evolution, characterized using optical metallography and electron-backscatter diffraction (EBSD), was found to vary significantly across the three 316L SS microstructures while the three samples loaded to a peak shock stress of 6.5 GPa displayed only ~12% differences in spall strength.

316L SS↗

Yield strength of Cu and a CuPb alloy (1% Pb)

With PBX9501 we explosively loaded fully annealed OFHC-Cu and an OFHC-CuPb (extruded with 1% Pb that ag- gregates at the Cu grain boundaries) to study the effects of the 1% Pb on the elastic-plastic yield Y of Cu. The yield-stress Y was studied through observation of surface velocimetry and total ejected mass ρ A from periodic surface perturbations machined onto the sample surfaces. The perturbation’s wavelengths were λ $\approx$ 65 µm, and their amplitudes h were varied to determine the wavenumber (2π/λ) amplitude product kh at which ejecta production for the Cu and CuPb begins, which relates to Y. The Y of the two materials is apparently different.

36 MATERIALS SCIENCE↗

Dynamic failure in two-phase materials

Previous experimental research has shown that microstructural features such as interfaces, inclusions, vacancies, and heterogeneities can all act as voidnucleation sites. However, it is not well understood how important these interfaces are to damage evolution and failure as a function of the surrounding parentmaterials. In this work, we present results on three different polycrystallinematerials: (1) Cu, (2) Cu-24 wt. %Ag, and (3) Cu-15 wt. %Nb which were studied to probe the influence of bi-metal interfaces onvoidnucleation and growth. These materials were chosen due to the range of difference in structure and bulk properties between the two phases. The initial results suggest that when there are significant differences between the bulk properties (for example: stacking fault energy, melting temperature, etc.) the type of interface between the two parent materials does not principally control the damage nucleation and growth process. Rather, it is the “weaker” material that dictates the dynamic spall strength of the overall two-phase material.

36 MATERIALS SCIENCE↗