Engineering Papers⌕ Search

Engineering topics

Fei Li

Publications and source records attributed to Fei Li.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Secondary Instability of Stationary Crossflow Vortices in Mach 6 Boundary Layer Over a Circular Cone

Hypersonic boundary layer flows over a circular cone at moderate incidence can support strong crossflow instability. Due to more efficient excitation of stationary crossflow vortices by surface roughness, such boundary layer flows may transition to turbulence via rapid amplification of the high-frequency secondary instabilities of finite amplitude stationary crossflow vortices. The amplification characteristics of these secondary instabilities are investigated for crossflow vortices generated by an azimuthally periodic array of roughness elements over a 7-degree half-angle circular cone in a Mach 6 free stream. Depending on the local amplitude of the stationary crossflow mode, the most unstable secondary disturbances either originate from the second (i.e., Mack) mode instabilities of the unperturbed boundary layer or correspond to genuine secondary instabilities that reduce to stable disturbances at sufficiently small amplitudes of the stationary crossflow vortex. The predicted frequencies of dominant secondary disturbances are similar to those measured during wind tunnel experiments at Purdue University and the Technical University of Braunschweig, Germany.

Boundary layer flow↗
NASA NTRSDate not supplied

TPSAS-NF1676L-13025-DND

SWIFT Flight Experiments: receptivity to surface roughness can have large impact on transition location.

Meelan Choudhari↗
NASA NTRSDate not supplied

TPSAS-NF1676L-13027-DND

Outline - Motivation - Transition control using discrete roughness elements (DRE) - Subsonic Aircraft Roughness Glove Experiment (SARGE) - Crossflow transition in the absence of control - Effect of control - Concluding Remarks

Mujeeb Malik↗
NASA NTRSDate not supplied

Transition Modeling Based on the Dual N-factor Method for the CRM-NLF Wind Tunnel Configuration

The dual N-factor method is used to model the boundary-layer transition over the common research model with natural laminar flow (CRM-NLF) aircraft configuration. The flow conditions match selected test conditions from a wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. The paper presents a systematic methodology for transition prediction in the presence of a dual shock system and extends the prior capability for iteratively coupled computational fluid dynamics (CFD) predictions to incorporate three-dimensional, transonic wings. The method employs stability computations based on the linear parabolized stability equations (PSE), along with a dual N-factor criterion. The iterative process begins with the fully turbulent Reynolds-averaged-Navier-Stokes (RANS) mean flow solution. For the first iteration, a mean flow solution is calculated with an imposed transition front that aligns with the shock front from the fully turbulent solution. Subsequently, stability computations are performed along a set of streamlines across the wing to calculate the amplification of planar Tollmien-Schlichting (TS) and stationary crossflow (CF) modes. The transition criterion based on the dual N-factor method is used to infer the updated transition front and the process is successively repeated until convergence of the solution. Within three iterations, the predicted fronts for angles of attack of 1.45, 1.98, 2.46 and 2.94 degrees and a mean-aerodynamic-chord Reynolds number equal to 15 million, approach visual convergence in most regions of the studied cases, and the resulting predictions are in good agreement with the transition fronts deduced from measurements of temperature-sensitive paint. Even though surface pressure measurements based on fully-turbulent flow agree well with the measured pressure coefficient distributions, strong viscous-inviscid interaction effects cause significant shifts in the shock locations based on the imposed transition front, underscoring the intrusive nature of static pressure measurements using surface mounted ports on the CRM-NLF configuration.

Boundary Layer Transition↗
NASA NTRSDate not supplied

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

The linear amplification of modal disturbances that lead to boundary-layer transition in two-dimensional/axisymmetric hypersonic configurations is strongly reduced by the presence of a blunt nosetip, and the mechanisms underlying the observed onset of transition over the cone frustum are currently unknown. Linear nonmodal analysis has shown that both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification for moderate to large nosetip bluntness. The present study extends the previous linear analysis by including the nonlinear effects. Specifically, the perturbation form of the 2D, harmonic Navier-Stokes equations (HNSE) are solved with a fully implicit formulation and the Newton-Raphson method. The increased number of degrees of freedom for the nonlinear system presents difficulties for solution strategies based on direct solution of the linearized system. Such difficulties are overcome by using the GMRES iterative method with a preconditioner corresponding to a simplified Jacobian without the cross derivative terms. The HNSE solver is verified by comparing with nonlinear parabolized stability equation (NPSE) results for the nonlinear evolution of planar waves in an incompressible Blasius boundary layer and in a Mach 6 flow over a blunt cone. Finally, nonlinear nonmodal results are presented for planar traveling disturbances over the blunt cone. The nonmodal analysis demonstrates that entropy-layer disturbances generated close to the nose tip can seed the amplification of higher frequency Mack’s second-mode instabilities further downstream.

boundary layer transition↗
NASA NTRSDate not supplied

Modeling Boundary-Layer Transition in Subsonic Flow over a Swept Wing

Predicting the onset of boundary-layer transition is often more accurate using physics-based models that directly compute disturbance growth rather than phenomenological models often implemented into industrial CFD codes. The aim of this ongoing study is to calibrate linear, physics-based computations of transition in subsonic flows over swept wings against a large set of experimental data. Advancing the calibration of linear models of transition contributes to the CFD-Vision-2030 goal of automated boundary-layer transition prediction. This progress report uses the dual N-factor method to model transition over the swept NACA 64-2-015A wing. The flow conditions match selected test conditions from an extensive experimental dataset acquired from the NASA Ames 12-ft Pressure Tunnel. The OVERFLOW 2.4b flow solver is used to obtain laminar basic states based on an infinite-span assumption. Stability analyses are performed on 365 distinct configurations with linear stability theory (LST) and parabolized stability equations (PSE) from the Langley Stability and Transition Analysis Codes (LASTRAC), modeling the growth of Tollmien-Schlichting (TS) and stationary crossflow (SCF) disturbances. From a total of 67 data points for unswept, i.e., TS-dominant configurations, the critical N-factor based on PSE is found to be N_TS = 9. The SCF critical N-factor is found to be near 8 for the highly swept, SCF-dominant configurations. Dual N-factor curves for both LST and PSE computations demonstrate a high level of interaction between TS and SCF. It may be worthwhile to investigate an alternate metric to visualize maximal SCF amplification upstream of the transition location to account for the growth of SCF modes near the leading edge, which is not considered in the conventional applications of the dual N-factor criterion.

boundary-layer transition↗
NASA NTRSDate not supplied

Separation and Transition on a CCF: Experimental Campaigns

Several experimental campaigns have been conducted across a number of Mach-6 facilities on the hypersonic flow around a CCF (CCF) geometry with a 5° half-angle cone and a 12° half-angle flare. These experiments were conducted as part of the NATO STO Research Task Group AVT-346, which is focused on predicting hypersonic boundary-layer transition on complex geometries. Two conventional wind tunnels (AFRL M6LT and ONERA R2Ch) and one quiet tunnel (Purdue BAM6QT) were used to test the same CCF geometry and to study the instabilities in both the boundary layer in the attached parts of the flow and the shear layer above the axisymmetric separation bubble near the cylinder-cone junction. Two nosetip radii (one nominally sharp and one blunt with a 5 mm radius) were tested. For the sharp nosetip case, there was a great deal of agreement between the measurements of both second-mode and shear-layer instabilities across the two conventional facilities. However, the measured spectra for the blunt nosetip case showed more significant differences between the two tunnels, potentially due to an alternate dominant instability mechanism coupled with the variations in the freestream noise spectra. The quiet facility resulted in a flow that remained laminar to much higher freestream unit Reynolds numbers, as well as in instability measurements that had more distinct spectral peaks for the sharp tip case and broadband rises for the blunt one. The instability mechanisms at play in the sharp quiet case were found to be the same as those in the conventional facilities.

Boundary Layer Transition↗
NASA NTRSDate not supplied

Ground Tests on the BOLT Geometry at Mach 7: Cross-Facility Comparison and Stability Analysis

Transition measurements have been obtained through two experimental campaigns conducted independently by the German Aerospace Center and the French Aerospace Lab with the French Alternative Energies and Atomic Energy Commission on subscale models of the BOLT-1 flight experiment geometry. This paper details a cross-facility comparison of measurements obtained at Mach 7, as well as subsequent computational analysis. Infrared (IR) thermography measurements obtained by both campaigns have facilitated a global comparison of the transition front across facilities at analagous conditions, which are found to be in good agreement. High-frequency surface pressure fluctuation data demonstrate significant amplification of instabilities with Mack-mode characteristics in the outboard regions of the acreage. These measurements are compared to stability analyses of varying fidelity. The computational methods employed to characterize the boundary-layer transition phenomena include the traditional line-marching implementation of the Parabolized Stability Equations (PSE), 2D eigenvalue analysis coupled with PSE, and Adaptive Mesh Refinement Wavepacket Tracking. While the 2D eigenvalue analysis is found to predict instabilities, which correlate in terms of frequency and acreage location to the experimental measurements, the predicted amplification for these instabilities is lower than would typically be expected for transition. Line-marching results for traveling crossflow produce the best match to the experimental transition front, with a consistent transition N factor of approximately 3-3.5.

Boundary Layer Transition↗
NASA NTRSDate not supplied

Separation and Transition on a Cone-Cylinder-Flare: Computational Investigations

Base flow computation and stability analysis were conducted for hypersonic flow over a cone-cylinder-flare (CCF) geometry for conditions that correspond to the experimental runs carried out in three wind tunnels. Owing to the presence of an attached boundary layer, a separation bubble induced by a shock-boundary layer interaction, and a reattachment region, the chosen flow configuration is physically rich. The complexity of this flowfield encompasses a combination of convective instabilities developing on the cone, global instabilities in the separation bubble, and shear-layer modes and streaks in the reattachment region. Thus, the selected CCF configuration provides the opportunity for a comprehensive comparison of the currently available methodologies for analyzing boundary layer instabilities. Various tools are used for the analysis, including global stability codes as well as convective instability analyses based on a local theory, a weakly non-parallel analysis, and tools that are applicable to strongly non-parallel flows. The paper presents a comparison of the convective instability characteristics based on different methodologies, such as linear stability theory (LST), the harmonic form of linearized Navier-Stokes equations (HLNSE), and resolvent analysis. The CCF configuration provided an effective framework for conducting a detailed cross-validation of this type, which had not yet been addressed in existing literature. This document is accompanied by a companion paper that is focused on the experimental aspects of the CCF configuration. Both papers are being presented in a dedicated session that highlights the research activities of the NATO STO Research Task Group AVT-346.

Boundary Layer Transition↗
NASA NTRSDate not supplied

Modeling Boundary-Layer Transition in Subsonic Flow over a Swept Wing

Predicting the onset of boundary-layer transition is often more accurate using physics-based models that directly compute disturbance growth rather than phenomenological models often implemented into industrial CFD codes. The aim of this ongoing study is to calibrate linear, physics-based computations of transition in subsonic flows over swept wings against a large set of experimental data. Advancing the calibration of linear models of transition contributes to the CFD-Vision-2030 goal of automated boundary-layer transition prediction. This progress report uses the dual N-factor method to model transition over the swept NACA 64-2-015A wing. The flow conditions match selected test conditions from an extensive experimental dataset acquired from the NASA Ames 12-ft Pressure Tunnel. The OVERFLOW 2.4b flow solver is used to obtain laminar basic states based on an infinite-span assumption. Stability analyses are performed on 365 distinct configurations with linear stability theory (LST) and parabolized stability equations (PSE) from the Langley Stability and Transition Analysis Codes (LASTRAC), modeling the growth of Tollmien-Schlichting (TS) and stationary crossflow (SCF) disturbances. From a total of 67 data points for unswept, i.e., TS-dominant configurations, the critical N-factor based on PSE is found to be N_TS = 9. The SCF critical N-factor is found to be near 8 for the highly swept, SCF-dominant configurations. Dual N-factor curves for both LST and PSE computations demonstrate a high level of interaction between TS and SCF. It may be worthwhile to investigate an alternate metric to visualize maximal SCF amplification upstream of the transition location to account for the growth of SCF modes near the leading edge, which is not considered in the conventional applications of the dual N-factor criterion.

computational modeling↗